《HarmanKardon-AVR35-avr-sm2维修电路图 手册.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR35-avr-sm2维修电路图 手册.pdf(80页珍藏版)》请在收音机爱好者资料库上搜索。
1、RadioFans.CN Continuous Power Output Tuning Cover Range 100kHz Step for AVR-35 (STEREO MODE), Input : CD THD : 0.08%, 8 ohms Both Channel Driven(20Hz-20kHz) (SURROUND MODE) THD : 0.5%, 8 ohms, 1kHz THD : at 60W, 8 ohms, Input : CD 20Hz 1kHz 20kHz IM Distortion at 45W, 8 ohms, Vol : Max. Input Sensit
2、ivity for Rated Power Output(35W) CD/DVD/TAPE MONITOR VID1/VID2/VID3 S/N Ratio Input Shorted at 1 kHz 1W Output(WTD IHF-A) CD Tone Control Bass : 100Hz Treble : 10kHz 100Hz 1kHz 10kHz Frequency Response at-3dB Channel Crosstalk Input Shorted by 1 K Ohms Mode : Stereo(1Watt) NominalLimit 50W 40W 45W
3、RMS Output Power THD(0.5%, 8 ohms, 1kHz) All Channel Driven S/N Ratio(Input Level : 200mV) Input Shorted, IHF-A WTD Frequency Respones at-3dB 8 ohms, Dolby Pro Logic 40W 65dB 100Hz-20kHz 150Hz-20kHz 35W 60dB RMS Output Power THD(0.5%, 8 ohms, 1kHz) All Channel Driven S/N Ratio(Input Shorted, IHF-A W
4、TD) Delay : 20ms, Input Level : 200mV Frequency Response at-3dB 8 ohms, Dolby Pro Logic 40W 65dB 100Hz-7kHz150Hz-7kHz 35W 60dB ohm/1dB DC-6 MHz VID1/VID2/VID3 Output Level / Impedance VID1/VID2/VID3 Frequency Response at-3dB 1Vp-p/75 DC-8 MHz 1Vp-p/75ohm/1dB Low pass crossover frequency Slope (Low P
5、ass Filter) Surround mode : BYPASS(STEREO) Input Signal : L ch (only) 200mV Master Volume :5dB 70Hz cut off 24dB/octave 35W 0.08% 0.08% 0.08% 0.03% 0.03% 0.03% 0.08% 170230mV 170230mV 0.03% 200mV 200mV 10dB3dB 10dB3dB 10dB3dB 10dB3dB 10Hz-80kHz 82dB 10dB 10dB 10dB 10dB 63dB 63dB 62dB 10Hz-70kHz 55dB
6、 55dB 45dB NominalLimit NominalLimit Line Level at Pre Out Input Sensitivity / impedance 87.50 - 108.00 MHz - 2 - RadioFans.CN 17.2dbf 70dB 80dB 43.3dbf 0.5% 60dB 1.0dB 4.0dB 450B 39.2dbf 65dbf 2.5dB 35dB 350-650mV Tuning Cover Range(MW) AVR-35 : 10kHz/Step AVR-35RDS/SG : 9kHz Step Usable Sensitivit
7、y(MW, at 999 / 1000kHz) NominalLimit 520-1710kHz 522-1611kHz 500uV/m00uV/m Tuning Cover Range 50 kHz Step for AVR-35RDS/SGImage Rejection(at 999kHz) IF Rejection(at 999/1000kHz) AGC Figure of Merit(From 100mV/m at 999/1000kHz) Distortion(999/1000kHz, 30% MOD, 50mV/m Input) Frequency Response(999/100
8、0Hz) At-3dB Selectivity(999/1000Hz) 9kHz/10kHz S/N Ratio(999/1000kHz, With Antenna Input 5mV/m) Overload Break-up at 999/1000kHz(THD 10%) Tape Output Level at 999/1000kHz(5mV/m Input) Mono Usable Sensitivity(75 ohms Input, 98MHz) Image Rejection(at 98MHz) IF Rejection(at 90MHz) 46dB Queting Sensitiv
9、ity(at 98MHz, 100% MOD.) Stereo Distortion(1kHz, 75kHz dev. At 98MHz, 71dbf Input) Mono S/N Ratio(500uV Input, 100% MOD. At 98MHz) Stereo Frequency Response(30Hz-15kHz) AVR-35 De-Emphasis : 75 AVR-35RDS/SG De-Emphasis : 50 AM Suppression at 98MHz Muting Threshold(at 98MHz) Overload Break-up at 98 MH
10、z Capture Ratio at 65dbf Stereo Separation(at 98MHz, 100% MOD, 500Input) IHF Band Pass Filter 1kHz Tape out Level(at 98MHz) 14.2dbf 80dB 90dB 39.2dbf 0.3% 65dB 0.5dB 2.0dB 50dB 31.2dbf 71dbf 2dB 40dB 500mV 40dB 50dB 50dB 1.0% 100Hz-2.2kHz 30dB 45dB 1000mV/m 200mV 0dB 5dB 5dB .0% 150Hz-1.8kHz dB 40dB
11、 00mV/m 160-240mV Power Consumption At Rated Power All Channel Driven Idling at Minimum Volume Control Power Supplies : USA/Canada(AVR-35) Europe(AVR-35RDS/SG) Dimension(W x H x D) Inches MM Weight(Ibs/kgs) These specifications are service target specs. specifications and components are subject to c
12、hange without notice. Overall performance will be maintained or improved. AC120V, 60Hz AC230V, 50Hz 17.36.517.1 440165435 29/13.2 332W 72W - 3 - 87.50 108.00MHz RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are spec
13、ial significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to deter
14、mine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typica
15、l ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor
16、-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After r
17、emoving an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static sold
18、er removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from i
19、ts protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads o
20、f a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES dev
21、ices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : - 4 - RadioFans.CN 1. Inspect all lead dress to make certain that leads are not pinche
22、d or that hardware is not lodged between the chassis and other metal partsintheunit. 2. Be sure that any protective devices such as nonmetallic control knobs, insulating fish- papers,cabinetbacks,adjustmentand compartment covers or shields, isolation resistor-capacitynetworks,mechanical insulators,
23、etc. Which were removed for the servicingareproperlyre-installed. Before returning the unit to the user, perform the following safety checks : 3. Be sure that no shock hazard exists ; check for leakage currentusingSimpsonModel229LeakageTester,standard equipment item No. 21641, RCA Model WT540A or us
24、e alternate method asfollows : Plug the power cord directly Into a 120 volt AC receptacle (do not use an Isolation Transformer for this test). Using two clip leads, connect a 1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,such as a wat
25、er pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltage drop across the resistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal, cabinet,screwheads,knobsandcontrolshafts
26、,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistestshouldbe performedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningthe unittotheowner. - 5 - RadioFans.CN Delay : Digital Input Selector : OpticalCoaxial Digital Set Button : C
27、hannel Selector : Speaker Selector Button : Selector Buttons : Information Display : Remote Sensor Window : Press this button to begin the sequence of steps required to enter delay time settings. When playing a source that has a digital output, press this button to select between the(17) and (16)inp
28、uts. When making choices during the setup and configuration process, press this button to enter the desired setting, as shown in the information Display, into the AVR-35s memory. Press this button to begin the process of selecting and configuring the AVR-35s output channels. Press this button to beg
29、in the process of selecting the speaker positions that are used in your listening room. When you are establishing the AVR-35s configuration settings, use these buttons to select between the choices available. as shown in the information Display. This display delivers messages and status indications
30、to help you operate the receiver. The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed. listening to a program that carries the Dolby Digital surround mode when listenin
31、g to a program that carries the Dolby Digital information. Press this button to select the Dolby Pro Logic surround mode when listening to an analog or digital(PCM) program that is encoded with surround-sound information. Press this button to select the Dolby 3 Stereo listening mode. This mode is us
32、ed primarily when a program has surround information when a center channel speaker, but no surround speakers, is installed. Press one of these buttons to select the analog surround modes. These modes may be used with any analog program source to create a pleasing surround effect. press this button t
33、o begin to sequence of steps used to set the AVR-35s output levels. When this button is pressed, a test tone will replace the currently selected listening source. Press this button to turn off all surround processing, and to listen to a program in traditional stereo from the left front and right fro
34、nt speakers only. Press this button to momentarily silence the speaker output of the AVR-35. Turn the knob clockwise to increase volume, counter clockwise to decrease the volume. Dolby Pro Logic Selector : Dolby 3 Stereo Selector : Surround Mode Selectors : Test Tone : Surround Off : Mute : Volume C
35、ontrol : Tuning button : TUNED Press the left side of the button to tune lower frequency station and the right side of the button to tune higher frequency stations. When a station with a strong signal is tuned, theindicatorwill illuminate in the Information Display. A brief(1/2 second) press of the
36、button will manually tune to the next frequency increment, while pressing and holding the button for a long period will automatically tune to the next station with a signal strong enough for acceptable reception. Press this button to automatically scan through the station that have been programmed i
37、n the AVR-35s memory. The tuner will play five seconds of each station before moving to the next preset station. To stop the scan when the desired station is heard, press the button again. Press this button to select stations that have been entered into the preset memory. Press this button to select
38、 the auto or mono mode for FM tuning. In the AUTO mode,indicator will illuminate in the information display, and when stations are transmitting stereo signals, the stereo reception will be provided and indicator will also be illuminated in the information display. In the MONO mode the left and right
39、 signals from stereo broadcasts will be mixed together and reproduced through all channels. Select MONO for better reception of weak signals. Press this button to select the Dolby Digital surround mode when Preset Scan : Preset Stations Selector : TUN.MODE/RDS : AUTO Stereo Dolby Digital Selector :
40、information Display CD : DVD Input : Video Input Selectors : Audio/Video AM/FM : Sleep Button : , and the red LED above the button will illuminate to remind you that you are listening to the tape monitor. Press this button to select the device connected to the CD Input jacks (5) as the listening sou
41、rce. Press this button to select the device connected to the DVD Input jacks (6) as the listening and viewing source. Press one of these buttons to select a source connected to the rear panelinputs (3), (14), or the front panel Press this button to select the tuner as the AVR-35s input source. When
42、it is first pressed the last station tuned will be heard. Press it again to change between AM and FM bands. Audio/Video input. Press this button to place the unit in the Sleep mode. After the time shown in the dispaly, the AVR35 will automatically go into the Standby mode. Each press of the button c
43、hanges the time until turn-off in the following order : Main Power Switch : NOTE : System Power Control : Power Indicator Power Indicator : Head Phone Jack : Press this button to apply power to the AVR-35. When the switch is pressed in the unit is placed in a Standby mode, as indicated by the amber
44、LED. This button MUST be pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the panel so that the word OFF may be read at the top of the switch. In normal operation this switch is left in the ON positio
45、n. When the Main Power Switch 1 is ON, press this button to turn on the AVR-35 ; press it again to turn the unit off. Note that the surrounding the switchwill turn green when the unit is on. This LED will illuminate in amber when the unit is in the Standby mode to signal that the unit is ready to be
46、 turned on. When the unit is in operation, the indicator will turn green. This jack may be used to listen to the AVR-35s output through a pair of headphones. Be certain that the headphones have a standard 1/4 stereo phone plug. Bass Control : Treble Control : Balance Control : NOTE : Video 3 Inputs
47、: T-Mon Selector : Tape Monitor Turn this control to modify the lower frequency output of the left / right channels by as much as +/-10dB. Set this control to a suitable position for your taste and room acoustics. Turn this control to modify the high frequency output of the left / right channels by
48、as much as +/-10dB. Set this control to a suitable position for your taste and room acoustics. Turn this control to change the relative volume for the front left / right channels. For proper operation of the surround modes this control should be at the midpoint, or 12 oclock position. These audio /
49、video inputs may be used for temporary connection of video games, camcorder, digital still cameras or portable audio products. To select a source connected to these jacks, press the Video 3 Input Selector. Press this button to select the device connected to thejacks (20) as the listening source. The previously selected source will continue to show in the CONTROLS AND FUNCTIONS Front Panel 32 30201051OFF 908070605040 minminminminminmin minminmin minminmin RadioFans.CN is being used to control a TV, VCR or Cable box.,press these button to change the channel being viewed. Press this butto