HarmanKardon-AVR130-avr-sm维修电路图 手册.pdf

《HarmanKardon-AVR130-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR130-avr-sm维修电路图 手册.pdf（119页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR130 AVR130 5 X 45W 5.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.7 REMOTE CONTROL FUNCTIONS.9 TROUBLESHOOTING GUIDE.13 PROCESSOR RESET.13 DISASSEMBLY.14 BULLETIN HK2003-10.15 TEC

2、H TIP HK2004-03.17 TECH TIP HK2003-01.21 UNIT EXPLODED VIEW.22 BLOCK DIAGRAM.23 AMP BIAS ADJUSTMENT.24 PCB DRAWINGS.25 ELECTRICAL PARTS LIST.31 SEMICONDUCTOR PINOUTS60 SCHEMATICS102 WIRING DIAGRAM.118 PACKAGING.119 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 7/2005 www.f

3、reeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement part

4、s designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product t

5、o the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip componen

6、ts. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground.

7、Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface su

8、ch as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical c

9、harges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devic

10、es are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which

11、 the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting o

12、f your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : AVR130 AVR130 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN 2 SAFETY PRECAUTIONS The following check should be performed for the continued prot

13、ection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal ove

14、rlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed o.5mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED

15、BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) AC Leakage Test Leakage current tester Reading should not be above 0.5mA Earth ground AVR130 AVR130 harman/kardon www.freeservicemanuals.

16、infoIts Free www.freeservicemanuals.info RadioFans.CN 4 TECHNICAL SPECIFICATIONS AVR 130 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average Power (FTC) 55 Watts per channel, 0.07% THD, 20Hz 20kHz, both channels driven into 8 ohms Five Channel Surround Modes Power Per Individual Ch

17、annel Front L press it again to turn the unit off.The Power Indicator 3 turns blue when the unit is on. 4 Headphone Jack: This jack may be used to listen to the AVR 130s output through a pair of headphones. The speakers will automatically be turned off when the headphone jack is in use. 5 Tone Mode

18、Selector Buttons: Pressing this but- ton enables or disables the Bass and Treble tone con- trols.When the button is pressed so that TONE IN appears in the Lower Display Line , the Bass and Treble controls may be used to adjust the output signals.When the button is pressed once or twice so that the w

19、ords TONE OUT appear in the Lower Display Line , the output signal will be “flat, ” no matter how the actual Bass and Treble Controls are adjusted. 6 Speaker Selector: Press this button to begin the process of configuring the unit to match the type of speakers used in your listening room. (See pages

20、 1619 for more information on speaker setup and configuration.) 7 Surround Mode Group Selector: Press this button to select the top-level group of surround modes. Each press of the button will select the current mode in each of the major groupings (e.g., Dolby, DTS, Logic 7, DSP, Stereo). When the b

21、utton is pressed so that the name of a mode in the desired surround-mode group appears in the on- screen display and in the Lower Display Line , press the Surround Mode Selector 8 to cycle through the individual modes available. For example, press this button to select Dolby modes,and then press the

22、 Surround Mode Selector 8 to choose from the various mode options. FRONT-PANEL CONTROLS 1 Main Power Switch 2 Power Indicator 3 Standby/On Switch 4 Headphone Jack 5 Tone Mode Selector Buttons 6 Speaker Selector 7 Surround Mode Group Selector 8 Surround Mode Selector 9 Tuning Selector )/Buttons ! Tun

23、er Band Selector Set Button # Digital Input Selector $ Preset Stations Selector % Delay Adjust Selector Input Source Selector keep them apart from other screw sets. 1) Remove the top cover, (13) Phillips screws. 2) Remove the volume, bass, treble and balance knobs by pulling them straight out and of

24、f. If a tool is necessary for removal of the smaller knobs, make sure the jaws are insulated to avoid knob damage. 3) Remove the (10) Phillips screws holding the front panel assy to the chassis: (6) at the bottom and (4) at the sides. 4) Cut all plastic cable ties that would prevent you detaching th

25、e front panel assy from the chassis. Draw a diagram if necessary, for a location reminder, to aid reassembly. 5) Unplug connector CN15 (6 cond) or CN89 (7 cond) at the left side of the unit. See below. 6) Remove single ground screw at the left side of the unit, near CN15 or CN89. (Black wire) 7) Unp

26、lug connector CN72 (32 cond) or CN81 (20 cond) on the DSP PCB, coming from the top of the front panel assy. See below. 8) There should now be enough slack in the connecting cables to lift and detach the front panel assy from the chassis. Pull the front panel as far away as the remaining connecting w

27、ires will allow, enough to tilt and gain access to the rear of the Tone/Volume PCB. See illustration Page 2. 9) Remove the (10) screws or (9) screws holding the Tone/Volume PCB to the front panel. 10) Detach and pull back the PCB; unplug top connector CN84 (7 cond) or CN83 (4 cond) if necessary. 11)

28、 Remove and replace VR74 or VR81 (5 soldered pads) with hk part# HSR2A029Z. 12) Reassemble in reverse order, taking care to replace all connectors, cable ties, and ground screw. 13) Power up receiver, and test volume control to assure setting no longer changes settings by itself, or when the volume

29、knob is tapped. AVR130 AVR130 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Model Serial Number 120V STATUS ACTION AVR130 AN0006-01000 to AN0006-13800 Volume control may not track accurately when turned; erratic operation Change VR74 Rotary encoder AVR130

30、 AN0006-13801 and above Modified By Factory NONE REQUIRED AVR230 AN0007-01000 to AN0007-11400 Volume control may not track accurately when turned; erratic operation Change VR74 Rotary encoder AVR230 AN0007-11401 and above Modified By Factory NONE REQUIRED AVR330 AN0008-01000 to AN0008-08524 Volume c

31、ontrol may not track accurately when turned; erratic operation Change VR74 Rotary encoder AVR330 AN0008-08525 and above Modified By Factory NONE REQUIRED HK3380 AN0015-01000 to AN0015-02728 Volume control may not track accurately when turned; erratic operation Change VR81 Rotary encoder HK3380 AN001

32、5-02729 and above Modified By Factory NONE REQUIRED HK3480 AN0016-01000 to AN0016-01864 Volume control may not track accurately when turned; erratic operation Change VR81 Rotary encoder HK3480 AN0016-01865 and above Modified By Factory NONE REQUIRED AVR130 AVR130 harman/kardon www.freeservicemanuals

33、.infoIts Free www.freeservicemanuals.info RadioFans.CN harman/kardon TECH TIPSTECH TIPS Troubleshooting tips and solutions to common service problems TIP# HKTT2004-03 Isolating audio problems in an AVR receiver Using 6/8 Direct In The following charts are used to help the tech quickly isolate audio

34、problems in an AVR receiver. Use the following procedures to help find what is working, then to quickly locate the problem area. Equipment needed: ? 1 set of (RCA) Y adaptors. ? Function/signal generator. ? Oscilloscope. Models covered: AVR210 AVR310 AVR220 AVR320 AVR520 AVR225 AVR125 AVR525 AVR130

35、AVR230 AVR330 AVR430 AVR630 Procedure: 1) Do a factory reset of the receiver. (This will eliminate any common micro processor problems.) Reset List can be found in this service manual. 2) Print the block diagram from the service manual. 3) With no inputs or speakers attached to the AVR turn on the r

36、eceiver and turn the volume all the way down. 4) Turn unit off. 5) Hook up an oscillator to the 6/8 Direct in jacks using the Y adaptors. Adjust the oscillator to about 0db (.775Volts RMS). 6) Hook up an oscilloscope to monitor the line out jacks. Or, if there are no line out (preamp out) jacks moni

37、tor the input to the power amps or the speaker outs. (AVR125, 225, 130 do not have preamp out jacks) 7) Turn the AVR on. Select 6 or 8 direct in, depending on the receiver. 8) Slowly turn the volume control up until you can easily measure the voltage at the line out jacks. ( -40 to -25db ) Harman Co

38、nsumer Group 250 Crossways Park Dr. Woodbury, New York 11797 Email T AVR130 AVR130 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Isolating audio problems in an AVR receiver Using 6/8 Direct In 9) At this point you will be able to check and assure all outp

39、ut levels are the same. 10) IF THE OUTPUT LEVELS ARE NOT THE SAME STOP! Go no further. At this point you will need to use the charts to see where you are losing your signal. The chart shows the analog signal flow from the input jacks to the output jacks. 11) If the output levels are the same check t

40、he power out stage at the speaker out jacks. 12) If you find the levels at the speaker out jacks are OK, your problem will be in the DSP part of the receiver. Congratulations! You have now eliminated 90% of the electronics in the AVR and confirmed that the problem is in the DSP section. Harman Consu

41、mer Group 250 Crossways Park Dr. Woodbury, New York 11797 Email T AVR130 AVR130 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Isolating audio problems in an AVR receiver Using 6/8 Direct In AVR,210,310,510 6 CH IN IC 501 In IC 501 Out CN 408 IC 704 In IC7

42、04 Out IC705 In IC705 Out IC706 In IC 706 Out IC 705 In IC 705 Out IC 716 In IC716 Out IC 717 In IC 717 Out IC 718 In IC 718 Out CP 405 FR31 15248943 19 17313 FL57 13 27 25 21 20 2526 10 12571 SR115776579 SL9 24 222223317 C5 21 191920315 SW78 101095711 AVR220 6 CH IN IC 501 In IC 501 Out CN 408 IC 7

43、04 In IC704 Out IC705 In IC705 Out IC706 In IC 706 Out IC714 In IC714 Out IC 705 In IC 705 Out IC 716 In IC716 Out IC 717 In IC 717 Out IC 718 In IC 718 Out CP 405 FR57 152489435710 12571 FL31 13 27 25 21 20 25263119 17313 SR115776579 SL9 24 222223317 C5 21 191920315 SW78 101095711 AVR320/520 8 CH I

44、N IC 501 In IC 501 Out CN 408 IC 704 In IC704 Out IC705 In IC705 Out IC706 In IC 706 Out IC714 In IC714 Out IC 705 In IC 705 Out IC 716 In IC716 Out IC 717 In IC 717 Out IC 718 In IC 718 Out CP 405 FR57 152489435710 12571 FL31 13 27 25 21 20 25263119 17313 SR115776579 SL9 24 222223317 C5 21 19192031

45、5 SW78 101095711 CN418 CP102 IC101 In IC101Out IC102 In ic102 oUT ic103 iN ic103 Out SBR3334 21 2357 SBL11 25 264231 AVR225/125 6 CH IN IC 30 In IC 30 Out IC 31 In IC 31 Out IC 32 In IC 32 Out IC 33 In IC 33 Out IC 34 In IC 34 Out BN12 IC 81 In IC 81 Out IC 80 In IC 80 Out BN16 In BN16 Out L ch27 25

46、 19 205713191012 R ch24 22 22 2331357 151445 SL5476579 SR24 10931 11 C8 1843317 SW21 19 25 26575 Harman Consumer Group 250 Crossways Park Dr. Woodbury, New York 11797 Email AVR130 AVR130 harman/kardon www.freeservicemanuals.infoIts Free www.freeservicemanuals.info RadioFans.CN Isolating audio proble

47、ms in an AVR receiver Using 6/8 Direct In 4 1 4 1 AVR 525 In Jack N404 P6 IC5 In IC5 Out IC3 In IC3 Out IC19 In IC19 Out IC18 In IC20 In IC20 Out IC3 In IC3 Out IC18 Out IC23 In IC23 Out IC25 In IC25 Out IC24 In IC24 Out IC26 In IC26 Out P9 N806 FL111094231353111 FR3321 2221 2357 2866733 SL552443315

48、5 SR77 29 2725 265777 CTR9957763199 SW11 11 26 2422 23571111 SBL13 138 10109311313 SBR15 15 23 2119 20671515 AVR130 6 ch in IC 23 In IC 23 Out IC 26 In IC 26 Out IC 42 In IC42 Out IC 4 In IC 44 Out IC 43 In IC 43 Out IC40 In IC40 Out IC49 In IC49 Out BN 12 BN1 L18 1721 231 R19 124214 SL24 2221 239 SR57427 C27 2521 235 SUB24423 SBL21 1921235713 SBR8 10423111 AVR230/330 6 ch in IC 23 In IC 23 Out IC 26 In IC 26 Out IC 42 In IC42 Out IC 4 In IC 44 Out IC 43 In IC 43 Out IC40 In IC40 Out IC49 In IC49 Out BN