《HarmanKardon-AVR55-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR55-avr-sm维修电路图 手册.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。
1、harman/kardon AVR55 AUDIO/VIDEO AC-3 PRO-LOGIC RECEIVER SERVICE MANUAL harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 RadioFans.CN CONTENTS SPECIFICATIONS.2 FRONT/REAR PANEL CONTROLS & CONNECTIONS .3 SET-UP/OPERATION GUIDE.12 TROUBLESHOOTING .26 BLOCK DIAGRAM (UNTILED & TILED)27
2、 EXPLODED VIEW .32 MECHANICAL PARTS LIST .34 ELECTRICAL PARTS LIST.35 SCHEMATICS AMPLIFIER (UNTILED & TILED).44 SCHEMATICS FRONT PCB (UNTILED & TILED).49 SCHEMATICS INPUT PCB (UNTILED & TILED).54 SCHEMATICS MAIN PCB (UNTILED & TILED).59 SCHEMATICS PRE-IN PCB (UNTILED & TILED).64 SCHEMATICS AC-3 PCB
3、(UNTILED & TILED).69 SCHEMATICS TUNER PCB (UNTILED & TILED).74 WIRING DIAGRAM (UNTILED & TILED).79 RadioFans.CN Technical Specifications AVR55 120 volt Audio Section Stereo Mode Continuous Average Power (FTC) 65 Watts per channel 20Hz20kHz: 0.07% THD, both channels driven into 8 Ohms Five-Channel Su
4、rround Mode Power Per Individual Channel Front L&R channels: 55 Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohms Center channel: 55 Watts, 20Hz20kHz into 8 ohms Surround channels: 55 Watts per channel, 40Hz20kHz into 8 ohms Input Sensitivity/Impedance Linear (High Level)200mV/32 Kohms Phono3mV/47
5、Kohms Signal-to-Noise Ratio (IHF-A) Linear (CD)95dB Phono73dB Surround System Adjacent Channel Separation Analog Decoding (Pro Logic, etc.)40dB Dolby Digital (AC-3)55dB Frequency Response 1W (+0, 3dB)8Hz100kHz High Instantaneous Current Capability (HCC)35 Amps Transient Intermodulation Distortion (T
6、IM)Unmeasurable Rise Time16sec Slew Rate40 V/sec FM Tuner Section Frequency Range87.5108 MHz Usable SensitivityIHF 1.3 V/14.2dBf Signal-to-Noise RatioMono/Stereo 70/68dB DistortionMono/Stereo 0.3/0.5% Stereo Separation1kHz, 40dB Selectivity400kHz 65dB Image Rejection98MHz 65dB Tuner Output Level1kHz
7、, 75kHz Dev 500mV AM Tuner Section Frequency Range5201710kHz Signal-to-Noise Ratio45dB Usable SensitivityLoop 500V Distortion1kHz, 50% Mod 0.8% Selectivity9kHz, 25dB General Power RequirementAC 120V 60Hz Power Consumption60W idle, 325W maximum (2 channels driven) Dimension (Max) Width17.4 inches (44
8、0 mm) Height6.3 inches (160 mm) Depth16.0 inches (406 mm) Weight32.6 lbs. (14.8 kg) Depth measurement includes knobs, buttons and terminal connections. All features and specifications are subject to change without notice. *Trademarks of Dolby Laboratories. DTS is a trademark of Digital Theater Syste
9、ms. UltraStereo is a trademark of UltraStereo Corp. RadioFans.CN 2 Front Panel Controls AVR55 120 volt 1 Main Power Switch 2 System Power Control 3 Power Indicator 4 Memo Button 5 Headphone Jack 6 FM Mode 7 Speaker Switch 8 AM/FM 9 Tuning Button ) CD ! Tape 1/Monitor Tape 2 # Phono $ TV % DVD Input
10、Vid 1 & Vid 1 Rec * Vid 2 ( Vid 2 Front/Rear Speaker Mode Selector Surround Off Bass Control Surround Mode Treble Control Digital Mode Selector Balance Control Digital Input Selector Night Mode Video 2 Inputs Contour Volume Control Subwoofer Level Adjust 3 3Center Level Adjust 3 4Surround Level Adju
11、st 3 5Information Display 3 6Remote Sensor Window 3 7Numeric Keys 67890 AVR 55 SpeakerHeadphones TUNEVID 1 REC. 12345 SPK. MODESURR.OFFFRT/REARVID 2SURR. MODENIGHT Volume Contour BassTrebleBalance MEMODVDVID 1DIGITAL INPUTDIGITAL Subwoofer Level Surround Level Center Level FM MODEAM/FMCDT MONPHONOTV
12、 VIDEO 2 RVideoLMaxMinMaxMinL Audio R Power RFCOAX OPT T 2 DIGITAL HALLTHEATERSTADIUMCHURCHSLEEP SOURCE VID 2 DVD TV PRO LOGIC VID 1 RECCONTOURSTEREOTUNEDAUTOMEMORYPRESETT MON 3 STEREO- 4)$*6 82 5 79#%&(!13 RadioFans.CN 3 Front Panel Controls AVR55 120 volt 1 Main Power Switch: Press this button to
13、apply power to the AVR55. When the switch is pressed the unit is placed in a Standby mode, as indicated by the amber LED 3 sur- rounding the System Power control 2. This button MUST be pressed in to operate the unit regardless of the status of the Power Switch at the bottom of the front panel. To tu
14、rn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out to extend from the front panel so that the word “OFF” may be read at the top of the switch. NOTE: In normal operation this switch may be left in the “on” position. 2 System Power Control: When
15、the Main Power Switch 1 is pressed in, press this button to turn on the AVR55, press it again to turn the unit off. Note that the Power Indicator surrounding the switch 3 will turn green when the unit is on. 3 Power Indicator: This LED will illuminate in amber when the unit is in the Standby mode, t
16、o signal that the unit is ready to be turned on. When the unit is in operation the indicator will turn green. 4 Memo Button: This button is used to enter settings for speaker modes, tuner presets and delay time after making the appropriate selection. 5 Headphone Jack: This jack may be used to listen
17、 to the AVR55s out- put through a pair of headphones. Be certain that the headphones have a standard 14 stereo phone plug. 6 FM Mode: Press this button to select the stereo or mono mode for FM tuning. In the STEREO mode a STEREOindicator will illuminate in the information display, and stereo recepti
18、on will be provided when sta- tions are transmitting stereo signals. In the MONO mode the left and right signals from stereo broadcasts will be mixed together and reproduced through all channels. Select MONO for better reception of weak signals. 7 Speaker Switch: This switch controls the front left/
19、right speakers. For normal operation it is pressed in and sound is heard through the front speakers. To silence the front left/right speakers, push the button once until it is in the “out” position. When the front speakers are turned off sound will continue to be heard through the center and rear sp
20、eakers and the headphone jack. 8 AM/FM: Press this button to select the tuner as the AVR55s input source. When it is first pressed the last station tuned will appear. Press it again to change between AM and FM bands. 9 Tuning Button: Press the left side of the button to tune lower frequency stations
21、 and the right side of the button to tune higher frequency stations. When a station with a strong frequency is tuned, the TUNED indicator will illuminate in the Information Display 3 5. A brief (1/2 second) press of the button will manually tune to the next frequency increment, while pressing and ho
22、ld- ing the button for a longer period will automatically tune to the next station with a signal strong enough for acceptable reception. ) CD: Press this button to select the device connected to the CD Input jacks d as the listening source. ! Tape1/Monitor: Press this button to select the device con
23、nected to the Tape 1 Play jacks as the lis- tening source. The T-Mon indicator K will illuminate to indicate that the Tape Monitor has been selected, while the input being monitored will remain in the Main Information Display F. Tape2: Press this button to select the device connected to the Tape 2 P
24、lay jacks as the listening source. # Phono: Press this button to select the Phono Input e as the listening source. $ TV: Press this button to select the device connected to the TV/Aux jacks as the listening and viewing source. % DVD Input: Press this button to select the device connected to the DVD
25、Play jacks as the listening and viewing source. Vid 1: Press this button to select the device connected to the Video 1 In jacks as the listening and viewing source. & Vid 1 Rec: Press this button to select the device that will be recorded by the device connected to the Video 1 Out jacks . The select
26、ed source is shown in the Vid 1 Source indicators A in the Information Display3 5. Note that this recording will take place even if another source is being listened to. * Vid 2: Press this button to select the device connected to the Video 2 Play jacks as the listening and viewing source. RadioFans.
27、CN 4 Front Panel Controls ( Vid 2 Front/Rear: Press this button to choose either the rear panel Video 2 Play jacks or the front panel Video 2 Inputs as the input source. When the green light above the button is illuminated, the front panel jacks are selected. Speaker Mode Selector: Press this button
28、 to configure the AVR55 for the type of speakers used in your system. See page 18 for details on using this button. Surround Off: Press this button to turn the surround modes off to listen to a source in traditional two- channel stereo from the front left/right speakers only. Bass Control: Turn this
29、 control to modify the low frequency output of the left/right channels by as much as 10dB. Set this control to a suitable position for your taste and room acoustics. Surround Mode: Press this button to select one of the analog surround processing modes (Dolby Pro Logic, Dolby 3 Stereo, Theater, Hall
30、, Stadium and Church) for a listening session. Treble Control: Turn this control to modify the high frequency output of the left/right channels by as much as 10dB. Set this control to a suitable position for your taste and room acoustics. Digital Mode Selector: Press this button to listen to a sourc
31、e when a PCM or Dolby Digital (AC-3*) signal is present. NOTE: Dolby Digital may only be used with the CD, TV, DVD, Vid 1 and Vid 2 inputs. Balance Control: Turn this control to change the relative volume for the front left/right channels. NOTE: For proper operation of the surround modes this contro
32、l should be at the midpoint, or “12 Oclock” position. Digital Input Selector: When the Digital Mode Selector has been pressed, this button is used to select the type of digital input to be used. NOTE: The coax or optical inputs may be selected with the CD, TV, DVD, Vid 1 and Vid 2 inputs. The RF inp
33、ut may be used with the Vid 1 input only. Night Mode: Press this button to activate the “Night” mode, pre- venting a loud playback when the digital modes are in use. Video 2 Inputs: These jack may be used to temporarily connect an audio/video source such as a video game or camcorder to the AVR55. To
34、 select these jacks as the input, press the Vid 2 Front/Rear button ( until the green LED above that button is illuminated. Contour: Press this button when listening at low levels to activate special circuits that compensate for the response of the human ear at lower volumes. In the off position the
35、 unit will provide flat frequency response. Volume Control: Turn the knob clockwise to increase volume, counterclockwise to decrease the volume. Note that approximately two revolutions of the knob are required to go from no output to maximum volume. Subwoofer Level Adjust: Press these buttons to rai
36、se or lower the output to the subwoofer channel. These buttons should be used dur- ing normal listening sessions for touch-up adjustments, not when the test signal is being used for major system alignment. 3 3Center Level Adjust: Press these buttons to raise or lower the output to the center channel
37、. These buttons should be using during normal listening sessions for touch- up adjustments, not when the test signal is being used for major system alignment. 3 4Surround Level Adjust: Press these buttons to raise or lower the output to the surround channels. These buttons should be used dur- ing no
38、rmal listening sessions for touch-up adjustments, not when the test signal is being used for major system alignment. 3 5Information Display: This display delivers messages and status indications to help you operate the receiver. Refer to the separate diagram for complete explanation of the FL displa
39、y. 3 6Remote Sensor Window: The sensor behind this window receives infrared signals from the remote con- trol. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed. 3 7Numeric Keys: Press these buttons to enter or recall stations entered to the tuner
40、s preset memory. See page 25 for complete information on using the tuner and the preset memories. AVR55 120 volt RadioFans.CN 5 Front Panel Information Display AVR55 120 volt DIGITAL HALLTHEATERSTADIUMCHURCHSLEEP SOURCE VID 2 DVD TV PRO LOGIC VID 1 RECCONTOURSTEREOTUNEDAUTOMEMORYPRESETT MON 3 STEREO
41、 - F MLKJIGH BA ? DEC A Vid 1 Record Indicators B Dolby Digital Indicator C Analog Dolby Surround Mode Indicators D Analog Surround Mode Indicators E Sleep Indicator F Main Information Display G Preset Indicator H Memory Indicator I Auto Mode In Indicator J Tuned Indicator K T-Mon Indicator L Stereo
42、 Indicator M Contour Indicator A Vid 1 Record Indicators: A dot appears next to one of the sources shown in this indicator to tell you which input has been selected as the output to the device connected to the Video 1 Out jacks . Press the Vid 1 Rec button & to change the source. B Dolby Digital Ind
43、icator: This indicator illuminates when a Dolby Digital source is being played. C Analog Dolby Surround Mode Indicators: These indicators illumi- nate when one of the analog (matrix) dolby Surround modes is in use. D Analog Surround Mode Indicators: These indicators illumi- nate when one of the DSP
44、generated analog surround modes is in use. E Sleep Indicator: This indicator is illuminated when the Sleep function is in use. The number that appears above the indicator is the number of minutes remaining before the AVR55 will return to the Standby mode. F Main Information Display: This display sho
45、ws messages relating to the status, input source, surround mode, tuner, volume level or other aspects of units operation. G Preset Indicator: This indicator illuminates when one of the stations entered into the preset memory is tuned. The number that appears below the indicator is the preset station
46、s memory. H Memory Indicator: This flashes after the Memo button 4 u has been pressed to indicate that you should quickly select and enter a preset memory location for a specific radio station. I Auto Mode In Indicator: This indicator illuminates when the “Auto” mode is in use for FM tuning. J Tuned
47、 Indicator: This indicator illuminates when a station is being received with sufficient signal strength to allow for acceptable listening quality. K T-Mon Indicator: This indicator illuminates when the Tape Monitor function is in use to remind you that you are listening to the record output of the d
48、evice connected to the Tape 1 Record jacks , not to the actual input source shown in the Information Display. L Stereo Indicator: This indicator illuminates when an FM station is being tuned in stereo. M Contour Indicator: This indicator illuminates when the Contour circuits have been engaged by pre
49、ssing the Contour button . RadioFans.CN 6 Rear Panel Connections AVR55 120 volt CENTER PRE-OUT REAR PRE OUT FRONT ANTENNAMAIN IN PRE OUT AM LOOP FM 75 SUB WOOFER OUT AC-3 RF/PCM GND COAXIAL/PCM OPTICAL/PCM MODEL NO.: AVR55 HARMAN KARDON NORTHRIDGE CALIFORNIA, U.S.A. R REAR SPEAKER (8) FRONT SPEAKER (8) CENTER SPEAKER (8) R L L SWITCHED 120V/60Hz TOTAL 100W 1A MAX AC OUTLETS OUT VIDEO MON. REMOTE CONTROL VIDEO 2 PLAY IN DVD PLAY TV/AUX OUT VID
免费区 
