HarmanKardon-AVR70.230-avr-sm维修电路图 手册.pdf

《HarmanKardon-AVR70.230-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR70.230-avr-sm维修电路图 手册.pdf（89页珍藏版）》请在收音机爱好者资料库上搜索。

1、Harman Kardon Service Manual AVR 70/230 5x75W 5.1 CHANNEL A/V RECEIVER Released EU2012 Harman Consumer Group, Inc. Rev 0, 06/2012 8500 Balboa Boulevard Northridge, California 91329 CONTENTS SEMICONDUCTOR PINOUTS 46 PCB DRAWINGS 63 BLOCK DIAGRAMS 74 WIRING DIAGRAM 78 SCHEMATIC DIAGRAMS 79 ESD WARNING

2、 2 OWNERS MANUAL 3 EXPLODED VIEW AND PARTS 29 TROUBLESHOOTING 30 PARTS LIST 33 RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only

3、the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before re

4、tuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semicon

5、ductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a

6、known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a c

7、onductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can g

8、enerate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

9、replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit

10、 assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fab

11、ric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : harman/kardonService manual AVR745EU Page 2 of 118 RadioFans.CN Audio/video receiver AVR 700/AVR 70/AVR 70C Owners Manual FPO RadioFans.CN AVR 700/AVR 70/AVR 70C 2 Intr

12、oductIon 3 SupplIed AcceSSorIeS 3 ImportAnt SAfety InformAtIon 3 plAce the AVr 3 front-pAnel controlS 4 reAr-pAnel connectorS 5 SyStem remote control functIonS 6 IntroductIon to home theAter 8 typIcAl home theAter SyStem 8 multIchAnnel AudIo 8 Surround modeS 8 plAce your SpeAkerS 8 plAcIng the left,

13、 center And rIght SpeAkerS 8 plAcIng the Surround SpeAkerS 8 plAcIng the Subwoofer 8 typeS of home theAter SyStem connectIonS 9 SpeAker connectIonS 9 Subwoofer connectIonS 9 Source deVIce connectIonS 9 VIdeo connectIonS 10 rAdIo connectIonS 10 uSb port 10 mAkIng connectIonS 11 connect your SpeAkerS

14、11 connect your Subwoofer 11 connect your tV or VIdeo dISplAy 11 connect your Source deVIceS 11 connect the rAdIo AntennAS 13 connect to Ac power 13 InStAll bAtterIeS In the remote control 13 Set up the AVr 14 turn on the AVr 14 uSIng the on-Screen menu SyStem 14 confIgure the AVr for your SpeAkerS

15、15 AddItIonAl Setup menu ItemS 15 operAtIng your AVr 16 controllIng the Volume 16 mutIng the Sound 16 lIStenIng through heAdphoneS 16 SelectIng A Source 16 VIdeo troubleShootIng tIpS 16 lIStenIng to fm And Am rAdIo 16 lIStenIng to medIA on A uSb deVIce 16 SelectIng A Surround mode 17 AdVAnced functI

16、onS 17 AudIo proceSSIng And Surround Sound 17 AdjuStIng the chAnnel VolumeS 17 recordIng 17 Sleep tImer 18 proceSSor reSet 18 memory 18 troubleShootIng 19 SpecIfIcAtIonS 20 AppendIx 21 Table of Contents RadioFans.CN AVR 700/AVR 70/AVR 70C 3 Introduction, Supplied Accessories, Important Safety Inform

17、ation and Place the AVR Introduction Thank you for choosing this Harman Kardon product! for more than fifty years, the harman kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Sidney harman and bernard kardon invente

18、d the receiver, a single component designed to simplify home entertainment without compromising performance. over the years, harman kardon products have become easier to use while offering more features and sounding better than ever. the AVr 70, AVr 700 and AVr 70c 5.1-channel digital audio/video re

19、ceivers (AVrs) continue this tradition with some of the most advanced audio and video processing capabilities yet and a wealth of listening and viewing options. to obtain the maximum enjoyment from your new AVr, please read this manual and refer back to it as you become more familiar with its featur

20、es and their operation. If you have any questions about this product, its installation or its operation, please contact your harman kardon retailer or custom installer, or visit our web site at www. . Supplied Accessories the following accessory items are supplied with your AVr. If any of these item

21、s are missing, please contact your harman kardon dealer, or harman kardon customer service at . IR remote control AM loop antenna FM wire antenna Three AAA batteries AC power cord IMPORTANT SAFETY INFORMATION Verify Line Voltage Before Use the AVr 700 has been designed for use with 120-volt alternat

22、ing current (Ac). the AVr 70 and AVr 70c have been designed for use with 220 240-volt Ac. connection to a line voltage other than that for which your AVr is intended can create a safety and fire hazard, and may damage the unit. If you have any questions about the voltage requirements for your specif

23、ic model or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet. Do Not Use Extension Cords to avoid safety hazards, use only the power cord supplied with your unit. we do not recommend that extension cords be used with this product. As with a

24、ll electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications. Handle the AC Power Cord Gently when disconnecting the power cord from a

25、n Ac outlet, always pull the plug; never pull the cord. If you do not intend to use your AVr for any considerable length of time, disconnect the plug from the Ac outlet. Do Not Open the Cabinet there are no user-serviceable components inside this product. opening the cabinet may present a shock haza

26、rd, and any modification to the product will void your warranty. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the Ac power source immediately, and consult an authorized service center. CATV or Antenna Grounding (AVR 700) If

27、an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the united States national electrical code, AnSI/nfpA no. 70-1984, provides information with respect to proper gr

28、ounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode. NOTE TO CATV SYSTEM INSTALLER: this reminder is

29、provided to call the cAtV (cable tV) system installers attention to article 820-40 of the nec, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possib

30、le. Place the AVR Place the AVR on a firm and level surface. Be certain that the surface and any mounting hardware can support the AVrs weight. Provide proper space above and below the AVR for ventilation. Recommended clearance distances are 30cm above the unit, 10cm behind the unit and 20cm on each

31、 side of the unit. If you install the AVR in a cabinet or other enclosed area, provide cooling air within the cabinet. under some circumstances, a fan may be required. Do not obstruct the ventilation slots on the top of the AVR or place objects directly over them. Do not place the AVR directly on a

32、carpeted surface. Do not place the AVR in moist or humid locations, in extremely hot or cold locations, in areas near heaters or heat registers, or in direct sunlight. RadioFans.CN AVR 700/AVR 70/AVR 70C 4 Front-Panel Controls Front-Panel Controls Main Power switch: this mechanical switch turns the

33、AVrs power supply on or off. It is usually left on and cannot be turned on or off using the remote control. Standby indicator: this led glows amber to indicate that the AVr is in the Standby mode. Power On/Standby button: press this button to turn the AVr on and put it into the Standby mode. when th

34、e AVr is on the power on indicator glows blue and the Standby indicator turns off. Stereo Mode button: places the AVr in the stereo listening mode. IR Sensor: this sensor receives infrared (Ir) commands from the remote control. It is important to ensure that the sensor is not blocked. Surround Mode

35、Select buttons: press these buttons to select a surround listening mode. Surround-mode availability depends on the nature of the source input signal, i.e., digital versus analog, and the number of channels encoded within the signal. Tuning Up/Down buttons: use these buttons to tune radio stations ac

36、cording to the setting of the Am/fm button (see below). AM/FM button: press this button to listen to the radio. pressing this button when the radio is in use will select among the fm Stereo, fm mono and Am bands. See Listening to FM and AM Radio, on page 16, for more information. Message display: Va

37、rious messages appear in this display in response to commands and changes in the incoming signal. In normal operation, the current source device name, surround mode and active input appear. when the on-screen display menu system (oSd) is in use, the current menu settings appear. IMPORTANT NOTE: If t

38、he protect message ever appears on the message display, turn off the AVr and unplug it from the Ac outlet. check all speaker wires for a possible short circuit (the “+” and “” conductors touching each other or both touching the same piece of metal). If a short circuit is not found, bring the unit to

39、 an authorized harman kardon service center for inspection and repair before using it again. Preset Selector buttons: when the radio is in use, press these buttons to cycle through your preset radio stations.(See Listening to FM and AM Radio, on page 16, for more information.) note: when youre liste

40、ning to files on a uSb device, the tuning up/down buttons and the preset Selector buttons serve as the uSb devices transport control buttons.(See Playing Files on a USB Device, on page 16, for more information.) Source Select buttons: press these buttons to select the active source device. Memory/Fo

41、lder button: when the radio is in use, press this button to set the current station as a preset. See Listening to FM and AM Radio, on page 16, for more information. when a uSb device is the active source deivce, press this button to display the contents of the current folder or to display all of the

42、 folders in the current directory level. See Playing files on a USB Device, on page 16, for more information. Headphone connector: connect a 1/4 stereo headphone plug to this jack for private listening USB Port: Insert a flash drive or hdd disk drive with a uSb Standard-A cable to this port. Volume

43、control: turn this knob to raise or lower the volume. Video 3 Audio and Video Input connectors: connect an auxiliary audio/video source component that will be used only temporarily, such as a camcorder, portable music player or game console, here. Standby Indicator message display Volume control pow

44、er on Indicator (inside Volume control ring) memory/folder button Surround mode Select buttons Ir Sensor main power Switch on/Standby Switch headphone connector Source Select buttons tuning up/down button Stereo mode button preset Selector buttons Am/fm button uSb port Video 3 Audio and Video Input

45、connectors RadioFans.CN AVR 700/AVR 70/AVR 70C 5 Rear-Panel Connectors Rear-Panel Connectors hdmI connectors digital Audio connectors Subwoofer connector Analog Audio connectors Speaker connectors radio Antenna connectors Ac Input connector composite Video connectors Radio Antenna connectors: connec

46、t the included Am and fm antennas to their respective terminals for radio reception. See Connect the Radio Antennas, on page 13, for more information. Digital Audio connectors: If your non-hdmI source devices have digital outputs, connect them to the AVrs digital audio connectors. See Connect Your S

47、ource Devices, on page 11, for more information. Analog Audio connectors: use the AVrs Analog Audio connectors for source devices that dont have hdmI or digital audio connectors. use the Video 1 out, Video 2 out and tape out connectors to connect to the audio inputs of Vcrs, tape decks or other anal

48、og recorders. See Connect Your Source Devices, on page 11, for more information. HDMI connectors: the hdmI (high-definition multimedia Interface) feature is a connection for transmitting digital audio and video signals between devices. If your source devices and tV have hdmI connectors, using them w

49、ill provide the best possible video and audio performance quality. Since the hdmI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via hdmI connections. See Connect Your Source Devices, on page 11, for more information. Notes on using the HDMI Out connector: When connecting a DVI-equipped display to the HDMI Monitor Out connector, use an hdmI-to-dVI