HarmanKardon-AVR165.230-avr-sm维修电路图 手册.pdf

《HarmanKardon-AVR165.230-avr-sm维修电路图 手册.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR165.230-avr-sm维修电路图 手册.pdf（111页珍藏版）》请在收音机爱好者资料库上搜索。

1、Harman Kardon Service Manual AVR 165/230 5.1 CHANNEL A/V RECEIVER Released EU2011 Harman Consumer Group, Inc. Rev 0, 10/2011 8500 Balboa Boulevard Northridge, California 91329 CONTENTS EXPLODED VIEW AND PARTS 15 PARTS LIST 16 IC PINOUTS 40 PCB DRAWINGS 87 BLOCK DIAGRAMS 97 WIRING DIAGRAM 99 AMP BIAS

2、 ADJUSTMENT 100 SCHEMATIC DIAGRAMS 101-111 ESD WARNING 2 FRONT AND REAR PANELS 3 REMOTE CONTROL 7 RESET REMOTE AND PROCESSOR 9 TROUBLESHOOTING GUIDE 10 BASIC SPECIFICATIONS 11 PACKAGE LISTS AND PARTS 13 DISASSEMBLY 14 RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components

3、 identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage

4、-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Ele

5、ctrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately bef

6、ore handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons p

7、rior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solde

8、r or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES

9、 devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately

10、 before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize b

11、odily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : Harman KardonAVR 165/230V Ser

12、vice Manual Page 2 of 111 RadioFans.CN 4 AVR 1650/AVR 165Front-Panel Controls Front-Panel Controls power Indicator Message display Volume knob Surround Mode Select buttons Set button Ir Sensor power button left/right buttons headphone Jack/ ezSet/eq Mic connector Source Select buttons tuning Mode bu

13、tton digital Input button Surround-Mode category button up/down buttons/ tuning buttons uSb port Aux Analog Audio Input connector channel level control button Harman KardonAVR 165/230V Service Manual Page 3 of 111 RadioFans.CN 5 AVR 1650/AVR 165 ENGLISH Front-Panel Controls, continued Front-Panel Co

14、ntrols, continued Power indicator: this led has three possible modes: led is off: Indicates that the AVr is unplugged or the rear-panel Main power switch is off. led glows amber: Indicates that the AVr is in the Standby mode. led glows white: Indicates that the AVr is turned on. IMPORTANT NOTE: If t

15、he protect message ever appears on the AVrs front-panel Message display, turn off the AVr and unplug it from the Ac outlet. check all speaker wires for a possible short circuit (the “+” and “” conductors touching each other or both touching the same piece of metal). If a short circuit is not found,

16、bring the unit to an authorized harman kardon service center for inspection and repair before using it again. IR sensor: this sensor receives infrared (Ir) commands from the remote control. It is important to ensure that the sensor is not blocked. Set button: press this button to select the currentl

17、y highlighted menu item. Message display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. when the on-screen di

18、splay menu system (oSd) is in use, the current menu settings appear. Surround-Mode Select buttons: After you have selected the desired surround-mode category, press these buttons to select a specific mode within the category, such as to change from dolby pro logic II Movie mode to logic 7 Movie mode

19、. Surround-mode availability depends on the nature of the source input signal, i.e., digital versus analog, and the number of channels encoded within the signal. Volume knob: turn this knob to raise or lower the volume. Power button: press this button to turn the AVr on or to place it in the Standby

20、 mode. Tuning Mode button: this button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned in. Channel Level Control button: press this button to

21、 activate the channel-level adjustment feature. After pressing this button, use the up/down buttons to select the channel for adjustment and use the left/right buttons to adjust the channels level. Digital Input button: press this button to change the audio input for the current source. use the left

22、/right buttons to cycle through the available inputs. Although you can assign any digital audio input to any source, the analog audio inputs are all permanently dedicated to the source with which they are labeled. Left/Right buttons: use these buttons to navigate the AVrs menus. Up/Down buttons/Tuni

23、ng buttons: use these buttons to navigate the AVrs menus. when the radio is the active source, use these buttons to tune stations according to the setting of the tuning Mode button (see above). Surround-Mode Category button: press this button to select a surround-sound category. each press changes t

24、he surround-mode category: Auto Select, Virtual, Stereo, Movie, Music and Video game. to change the specific surround-sound mode within the category, use the Surround Mode Select buttons. See Audio processing and Surround Sound, on page 20, for more information on surround modes. Headphone jack/EzSe

25、t/EQ Mic connector: connect a 1/4 stereo headphone plug to this jack for private listening. this jack is also used to connect the supplied microphone for the ezSet/eq procedure described in configure the AVr for Your Speakers, on page 17. Source Select buttons: press these buttons to select the acti

26、ve source. USB port: You can use this port to perform software upgrades that may be offered in the future. do not connect a storage device, a peripheral product or a pc here, unless instructed to do so as part of an upgrade procedure. Aux Analog Audio Input connector: connect an auxiliary source com

27、ponent that will be used only temporarily, such as a camcorder, portable music player or game console, here. Harman KardonAVR 165/230V Service Manual Page 4 of 111 RadioFans.CN 6 AVR 1650/AVR 165Rear-Panel Connectors Rear-Panel Connectors AVR 1650/AVR 165 Rear-Panel Connections (AVR 1650 shown) hdMI

28、 Input connectors hdMI Monitor out connector composite Video Monitor out connector dVd component Video Input connector radio Antenna connectors Subwoofer connector Analog Audio Input/output connectors Speaker connectors 12V trigger connector Main power Switch Ac Input connector optical digital outpu

29、t connector digital Audio Input connectors the bridge IIIp connector Ir remote In/out connectors composite Video Input connectors Video 2 out connector Harman KardonAVR 165/230V Service Manual Page 5 of 111 RadioFans.CN 7 AVR 1650/AVR 165 ENGLISH Rear-Panel Connectors, continued Rear-Panel Connector

30、s, continued Radio Antenna connectors: connect the included AM and FM antennas to their respective terminals for radio reception. HDMI Monitor Out connector: If your tV has an hdMI connector and you have hdMI or component video source devices, use an hdMI cable (not included) to connect it to the AV

31、rs hdMI Monitor out connector. Notes on using the HDMI Monitor Out connector: when connecting a dVI-equipped display to the hdMI Monitor out connector, use an hdMI-to-dVI adapter and make a separate audio connection. Make sure the hdMI-equipped display is hdcp-compliant. If it isnt, do not connect i

32、t via hdMI; use an analog video connection instead and make a separate audio connection. HDMI Input connectors: the hdMI (high-definition Multimedia Interface) feature is a connection for transmitting digital audio and video signals between devices. If your source devices have hdMI connectors, using

33、 them will provide the best possible video and audio performance quality. Since the hdMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via hdMI connections. See connect Your Source devices, on page 13, for

34、 more information. Composite Video Monitor Out connector: If your tV or video display does not have an hdMI connector, or if your tV does have an hdMI connector but you are connecting some source devices with only composite video connectors, use a composite video cable (not included) to connect the

35、AVrs composite Video Monitor out connector to your tVs composite video input connector. DVD Component Video Input connector: If your blu-ray disc or dVd player does not have an hdMI connector but does have a component video connector, using the component video connector will provide superior video p

36、erformance. You will also need to make an audio connection from the player to the AVr. Digital Audio Input connectors: If your non-hdMI source devices have digital outputs, connect them to the AVrs digital audio connectors. note: Make only one type of digital connection (hdMI, optical or coaxial) fr

37、om each device. See connect Your Source devices, on page 13, for more information. Video 2 Out connector: connect an analog video recorders video input connector to the AVrs Video 2 out connector. You can record any composite video input signal. note: to record the audio and video from the source de

38、vice, connect the AVrs Video 2 out Analog output connectors to the analog video recorders audio inputs. Composite Video Input connectors: use composite video connectors for video source devices that dont have hdMI or component video connectors. You will also need to make an audio connection from the

39、 source device to the AVr. See connect Your Source devices, on page 13, for more information. IR Remote In/Out connectors: when the Ir Sensor on the front panel is blocked (such as when the AVr is installed inside a cabinet), connect an optional Ir receiver to the Ir remote In connector. the Ir remo

40、te out connector may be connected to the Ir input of a compatible product to enable remote control through the AVr. See connect Ir equipment, on page 15, for more information. The Bridge IIIP connector: connect an optional harman kardon the bridge IIIp docking station to this connector. Insert the p

41、lug until it snaps into place in the connector. IMportAnt: connect the bridge IIIp only with the AVrs power turned off. See connect the bridge IIIp, on page 15, for more information. Subwoofer connector: connect this jack to a powered subwoofer with a line-level input. See connect Your Subwoofer, on

42、 page 13, for more information. Analog Audio Input/Output connectors: use the AVrs Analog Audio Input/output connectors for source devices that dont have hdMI or digital audio connectors. use the Video 2 out and tape out connectors to connect to the audio inputs of a Vcr and tape deck. See connect Y

43、our Source devices, on page 13, for more information. Speaker connectors: use two-conductor speaker wire to connect each set of terminals to the correct speaker. See connect Your Speakers, on page 13, for more information. Optical Digital Output connector: connect a digital audio recorders optical d

44、igital input to the AVrs optical digital output connector. You can record both coaxial and optical digital pcM audio signals. (dolby digital and dtS bitstreams are not available for recording.) Main Power switch: this mechanical switch turns the AVrs power supply on or off. It is usually left on and

45、 cannot be turned on or off using the remote control. 12V Trigger connector: this connector provides 12V dc whenever the AVr is on. It can be used to turn on and off other devices such as a powered subwoofer. AC Input connector: After you have made all other connections, plug the supplied Ac power c

46、ord into this receptacle and into an unswitched wall outlet. Harman KardonAVR 165/230V Service Manual Page 6 of 111 RadioFans.CN 8 AVR 1650/AVR 165System Remote Control Functions System Remote Control Functions Ir transmitter lens Mute button Source Selector buttons Volume up/down buttons Speaker Se

47、tup buttons ok button delay button number buttons Memory button Macro buttons transport control buttons display dimmer button disc Skip button (AVr 1650) rdS button (AVr 165) preset Station up/down buttons clear button left/right/up/down buttons program Indicator led AVr button Sleep/ch up/down butt

48、ons oSd button channel level control button digital Input button tuning Mode button direct Station entry button tuning up/down buttons tone control button night Mode button track Skip up/down buttons test tone button power off button power on button Harman KardonAVR 165/230V Service Manual Page 7 of

49、 111 RadioFans.CN 9 AVR 1650/AVR 165 ENGLISH System Remote Control Functions, continued System Remote Control Functions, continued In addition to controlling the AVr, the AVr remote is capable of controlling nine other devices, including an ipod/iphone device docked in a the bridge IIIp docking station connected to the AVr. during the installation process, you may program the codes for each of your source components into