HarmanKardon-FL8300-cd-sm维修电路原理图.pdf

《HarmanKardon-FL8300-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-FL8300-cd-sm维修电路原理图.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon Model FL8300 5 Disc Compact Disc Changer SERVICE MANUAL CONTENTS LASER BEAM SAFETY PRECAUTIONS .2 OTHER PRECAUTIONS . 3 LEAKAGE TEST . 4 SPEClFlCATlONS . 5 CONTROL AND FUNCTIONS . 7 BLOCK DIAGRAM .9 PICKUP REPLACEMENT.11 CIRCUIT DESCRlPTlON . 13 BULLETIN #9604. 22 BULLETIN #9607. 23 B

2、ULLETIN #9703.24 TECH TIP TIP# HKTT2003-02. 26 TROUBLESHOOTING . 27 PRINTED ClRCUlT BOARDS . 34 GENERAL UNIT EXPLODED VIEW I, II . .37 GENERAL UNIT PARTS LIST40 ELECTRICAL PARTS LIST . 41 SEMICONDUCTOR IDENTIFICATION. 44 PACKAGE .52 SCHEMATIC DIAGRAM . 53 WIRING DIAGRAM . . 61 harman/kardon, Inc. 25

3、0 Crossways Park Dr. Woodbury, New York 11797 Rev1 3/2003 RadioFans.CN RadioFans.CN RadioFans.CN 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 harman/kardon Service Bulletin Service bulletin # 9604 rev1 - October 1998This is considered a Minor Repair To: All harman/kardon Service Centers Models: FL830

4、0 Subject: Digital Output Level The Digital Interface Standard recommends D/A converters have a minimum Input sensitivity of 200 mV. In early FL8300 production units, the Digital Output level was 240 mV ?10% peak to peak. Based on our research, we found that some D/A converters require more than 240

5、 mV for intermittent free operation. In the event you receive a FL8300 from a consumer with the a complaint “Intermittent Sound from External D/A converter”, check the serial number in the table below. If the FL8300 has a serial number higher than indicated in the table below, connect a properly wor

6、king D/A converter to the Digital Output and verify interruption free operation. Also confirm the Digital Output level of the FL8300 is 500 mV ?10% Peak to Peak. If the FL8300 passes these two tests, advise the customer to have their external D/A converter and connecting cables checked. If the FL830

7、0 has a serial number lower than indicated in the table below, perform the following modification: 1) With the unit plugged in and turned on, push the “open/close” button to extend the drawer fully; then turn the unit off and unplug it. 2) Open the top cover (6 screws). 3) Remove output board PCB3 f

8、rom the rear panel (4 screws). This board can be pulled back and modified without completely removing it from the chassis. 4) Locate resistor R901, it may be a 680 ohm resistor or a jumper wire; replace in either case with a 0.47 uf capacitor h/k part# 5354-474593. 5) Locate R903 and change from 680

9、? to a 4.7k? resistor ? h/k part # 3029472970. Re-attach output PCB3 to the unit. 6) Connect a 75 Ohms cable to the digital output jack. Terminate this cable with a 75 Ohm load; connect an oscilloscope to the 75 Ohm termination resistor. While playing a CD, confirm the output of the signal is now 50

10、0 mV ?10% peak to peak. 7) Reassemble the FL8300 and test all functions. ModelSerial number 120V Serial number 230V StatusAction FL8300IN0019-01001 to IN0019-19393 IN0020-01001 to IN0020-04500 May have low digital output for some applications Replace R901 with 0.47 uf mylar capacitor h/k part# 5354-

11、474593 Replace R903 with 4.7k ohm resistor h/k part# 3029472970 FL8300IN0019-19394IN0020-04501Factory Installed *NONE REQUIRED * Factory modification of the FL8300 starting with the serial numbers indicated in the above table consisted of: R236: 1k Ohm R901: Jumper or 680 Ohm R903: Changed from 680

12、Ohm to 4.7k Ohm. Digital output level into 75 Ohms: 500 mV ? ?10% peak to peak. 22 harman/kardon Service Bulletin Service bulletin # 9607-January 97 This is considered a Major Repair To: All harman/kardon Service Centers Models: FL8300 Compact disc changer Subject: Failure to play Multi-media CDs or

13、 skip data tracks _ Early FL8300 CD Players used a micro-computer which could not read the table of contents (TOC) of certain multimedia CDs or skip data tracks on multimedia CDs. During two running production changes, new Microprocessor were installed which performs as shown in the table below: Des

14、cription IC112 Part Number Serial number Range120V Serial number Range230V Processor action Year/Month first used CXP21320-322 DWP325 2138322197 IN0019-01001 to IN0019-29000 IN0020-01001 to IN0020-05500 Does not play Multimedia CD 95 October CXP82320-352Q DWP325A 2139322710 IN0019-29001 to IN0019-53

15、790 IN0020-05501 to IN0020-08510 Plays Multimedia CD, Mutes at data track 96 July CXP82320-367Q DWP325B 2139322722 IN0019-53791 to present production IN0020-08511 to present production Plays Multimedia CD, Skips data tracks 96 November In the event you receive a FL8300 from a consumer with a complai

16、nt “Player will not read or, loudspeakers make strange noise while playing multimedia CDs”, replace IC112 with H/K Part number 2139322722. The IC can be identified by CXP82320-367Q DPW 325B printed on its case. harman/kardon Incorporated, 250 Crossways Park Dr. Woodbury, New York 11797 (516) 496-340

17、0 23 harman/kardon Incorporated, 250 Crossways Park Dr. Woodbury, New York 11797 (516) 496-3400 harman/kardon Service Bulletin Service bulletin # 9703 June 1997This is considered a Major Repair To:All harman/kardon Service Centers Models: FL8300 Subject: Dead unit, no display; Service upgrade In the

18、 event you receive an FL8300 that is dead, and upon inspection R701 is damaged or an otherwise open circuit, perform the necessary steps listed below: Due to current surges, early models of the FL8300 could repeatedly damage R701 (either a 1 ohm resistor or 1.5A micro fuse depending on version). Alo

19、ng with the replacement of R701, the positive lead should be relocated on C125 to suppress any future current surges. Additionally, two capacitors, now designated as C907 these will add stability to help prevent oscillation. PROCEDURE: 1) Replace R701 with micro-fuse H/K # 5508722221, this component

20、 is on PCB7. 2) A PCB trace should be cut on the C125 (2200 uf/25v) positive lead on the main circuit board and an insulated jumper wire attached from that lead to the junction of D109/110. Additionally another insulated jumper will need to replace the trace that was cut. (see drawing) 3) Add C907 J

21、153 is ground. Soldering one 1uf cap to the jumpers 185 J186 is ground. ModelSerial number 120V Serial number 230V ActionCorrection FL8300IN0019-72213 and below NOT REQUIREDR701 is damaged or an open circuit Replace R701, re-route positive connection on C125, Add C907/908 FL8300IN0019-72214 and abov

22、e NOT REQUIREDModified by factoryNONE REQUIRED 24 harman/kardon Incorporated, 250 Crossways Park Dr. Woodbury, New York 11797 (516) 496-3400 25 harman/kardon TECH TIPSTECH TIPS Troubleshooting tips and solutions to common service problems For models: FL8300 TIP# HKTT2003-02 Problem: Carousel not sto

23、pping in the correct position, so disc can be clamped correctly. Check: 1) 6-conductor Ribbon cable connection to sensor board - check cable; clean, re-seat at both ends. 2) There is a post/standoff underneath the single center screw in the center of the carousel (under the plastic 1,2,3,4,5 cap). I

24、f that post/standoff is too long, it can cause the symptom. If the part is higher than the surface of the carousel in that area, the part needs to be shaved down so its shorter. 3) Defective Roulette sensor (part# 2408001111) or Disc sensor (part# 2408210001). 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68