《HarmanKardon-SB16.230-spk-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-SB16.230-spk-sm维修电路原理图.pdf(29页珍藏版)》请在收音机爱好者资料库上搜索。
1、SB 16/230 Active Soundbar with wireless subwoofer Released EU2011 Harman Consumer Group, Inc. Rev 0, 06/2011 8500 Balboa Boulevard Northridge, California 91329 CONTENTS ESD WARNING 2 PACKAGE GUIDE AND PARTS, CENTER 3 PACKAGE GUIDE AND PARTS, SUB 4 EXPLODED VIEW AND PARTS, CENTER 5 EXPLODED VIEW AND
2、PARTS, SUB 6 PARTS LIST, SUB 7 SCHEMATIC DIAGRAMS 8 ASSEMBLY AND DISASSEMBLY, CENTER 12 OWNERS MANUAL 16-29 RadioFans.CN Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a componen
3、t identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from
4、 the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field e
5、ffect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charg
6、e on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devic
7、es, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not cl
8、assified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you ar
9、e ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective mater
10、ial to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing
11、 together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : RadioFans.CN RadioFans.CN harman/kardonSB 16/230 Service Manual Page 4 of 29 harman/kardonSB 16/230 Service Manual Page 5 of 29 1 2 3 4 5 6
12、 7 8 序號 品名料號 1 Screw for amplifier 10 數量 2 Amplifier 1 4 3 Logo Wood Cabinet 1 1 Rubber Foot 84 6 7 5 Screw for woofer Woofer 1 5 1 Logo fot grille 241-100-00613-2BCE 010-7610-05246-E 25PF12DZB-FW01-E 352-AM04020D210-E 316-AL-00553-E 316-AG-00557-E 352-FM04020D605-E 320-RUB-00057-0BAE 作 業 指 示 版本日期 2
13、009/12/030 頁次 1 客 戶: 機 種: 初版發行 0 ISSUEREVISIONS 表單編號:版 確認承認 DATENAME 制作 蔣國正 2009/12/03 務 注: 1.銘板(316-AL-00553-E)背後點3188膠水 再貼到鐵網卞槽中 2.銘板(316-AL-00553-E)的位置是:銘板下端距 靠LED燈的箱體邊緣60mm,左右居中 1 2 3 harman/kardonSB 16/230 Service Manual Page 6 of 29 Harman/Kardon SB 16/230 subwoofer, Exploded View Harman/Kardo
14、n SB15 wireless subwoofer. System Parts list. The sub is used in the SB 16/230 soundbar system. SB15 Sub Part NumberPart Description 352-AM04020D210-EScrew for Subwoofer 010-7610-05246-EAmplifier SB15/230 SUB 241-100-00613-2BCEWood Cabinet 316-AG-00557-EHarman Kardon Logo for the Sub top board 316-A
15、L-00553-ELogo for grille 25PF12DZB-FW01-E10 Subwoofer 352-FM04020D605-EScrew for woofer to wood cabinet 320-RUB-00057-0BAERubber pad for subwoofer cabinet 051-A05264D-EPOWER AMP PCB ASSY SB15 SUB 051-A05264C-EPCB WIRELESS BCB ASSY SB15 SUB 051-A05264B-EPRE AMP PCB ASSY SB15 SUB 051-A05264A-ESTANDBY
16、PCB ASSY SB15 SUB 302-FE-05275-0BAESubwoofer Amplifier panel 150-E0764201-ETransformer 152-V60202603-EPower Cord 154-V09006T0-EFuse 155-520020-EFuse holder 162-50652003-ESpeaker Wire 180-P3024DB-EPower Rock Switch 306-ABS-05082-0BAERear Enclosure 323-AL-05184-0LAEAluminum heat sink 335-NYL-00002-0BA
17、EPower Cord Strain Relief 311-ABS-00028-0BAEKnob harman/kardonSB 16/230 Service Manual Page 7 of 29 1 1 2 2 3 3 4 4 DD CC BB AA VSS VCC SGND VSS VCC SGND SGND 22K R01 22K R08 220P C02 18.7k R06 15.4k R04 17.8k R02 33n C04 24.9K R05 100p C03 220k R09 VCC 10k R07 VSS 220p C05 1 2 3 4 5 6 sw1 SW2-2 10K
18、 R03 10K R10 mout 84 7 5 6 2 U2B TL072CN 100n C06 VCC VSS 10u C01 8.25k R21 +12VC 100u C11 IN 3 2 OUT 1 GND U5 MC78L12CP VCC 3.3k R18 VCC VSS VCC VSS 100u C21 4.7u C23 SGND SGND SGND SGND VCC VSSSGND 220p C29 4.7u C34 100n C35 100n C25 4.7u C36 4.7u C26 100u C32 4.7u C37 4.7u C28 100n C13 100n C12 2
19、20n C38 100n C08 22n C27 47k R23 24.9k R19 22k R22 14.3k R20 VCC VSS SGND 100n C15 82.5k R15 12.1K R11 OUT Netsw1_3 6.8k R17 10u C16 220n C18 10u C17 V+ 1 OUTa 2 INa 3 INT 4 Vref 5 SENCE 6 SW 7 INb 8 OUTb 9 GND 10 U4 NJM2761-10 4.7u C22 VR2A VR*2 VR2B VR*2 A50k VR1 1 2 3 4 5 CON2 Header 5 SGND OUT 8
20、 1 4 3 2 1 U2A TL072CN 8 1 4 3 2 1 U3A TL072CN 84 7 5 6 2 U3B TL072CN mout 100n C09 VCC VSS SGND 100n C30 82.5k R16 12.1K R12 2 3 1 A 411 U1A TL074CD SGND VCC VSS 5 6 7 B 411 U1B TL074CD 10 9 8 C 411 U1C TL074CD 12 13 14 D 411 U1D TL074CD 1 2 3 4 5 CON1 Header 5 VSS VCC SGND CUSTOMER:JBL MODEL:SB 15
21、SUB/230 DETA:SEP.01.2009 PREPAREDCHECKEDCHECKEDAPPROVEDREV 1.0 PAGE2/5 BOARD: PERAMP harman/kardonSB 16/230 Service Manual Page 8 of 29 1 1 2 2 3 3 4 4 DD CC BB AA S/L 1 CLK INH 15 CLK 2 SI 10 A 11 B 12 C 13 D 14 E 3 F 4 G 5 H 6 QH 9 QH 7 VCC 16 GND 8 U04 SN74HC165D S/L 1 CLK INH 15 CLK 2 SI 10 A 11
22、 B 12 C 13 D 14 E 3 F 4 G 5 H 6 QH 9 QH 7 VCC 16 GND 8 U03 SN74HC165D 20K R08 20K R10 20K R12 20K R17 20K R19 20K R21 20K R23 20KR07 20KR09 20KR11 20KR14 20KR16 20KR18 20KR20 20KR22 10K R24 GNDGND GND GND 10K R15 GND 100R R13 1000u/10V C02 100n C03 10n C04 1000u/10V C07 100n C05 10n C06 100n C15 100
23、n C16 VCC VCC GNDGND 4.7R R04 4.7R R01 GND SCK 23 AGND2 24 LRCK 19 PI2 20 PC5 15 MCLK 16 MSIO0 7 MOSI0 8 SCK0 9 Vcc 4 /RST 5 RFVcc 1 AGND1 21 SDOUT 22 AVdd 25 PB1(CS0) 6 RFGND 2 GND 3 PF1(ID_CLK) 11 PC0(ID_LATCH) 12 /PC1(MUTE_LED) 13 PF0(ID_DATA) 10 /PC4(BOND_LED) 14 PC7(I2C_SDA) 17 PI0(I2C_SCL) 18
24、RX M1087 MD1 Rx M1087 /RST 1 SDATA 2 SCLK/DEM1 3 LRCK 4 MCLK 5 DIF1 6 DIF0 7 DEM0 8 FILT+ 9 VQ 10 REF_GND 11 AOUTR 12 AGND 13 AV 14 AOUTL 15 MUTEC 16 U06 CS4340 AGND 4.7K R33 100n C32 100n C29 100n C21 1000u/10V C20 10k R42 10k R43 10k R28 10k R40 1n C23 1n C31 AGND 8 1 4 3 2 U05A NJM4560 3.9k R35 2
25、0k R27 150p C19 3.9k R41 20k R39 150p C27 84 7 5 6 U05B NJM4560 AGND AGND AGND AGND GND 470u/16V C13 100n C14 VCC VCC VCC VCC AGND 33R R36 VCC 33R R25 470u/16V C18 100n C17 AGND VCC1 VCC1 GND AGND 1 2 3 4 5 SW1 SEL GND 1 2 3 4 5 6 7 8 CON1 Header 8 100n C01 GND 47k R03 VCC GND 100R R29 100R R30 100R
26、 R31 100R R32 AGND link1 GND 12 BD2 BD 12 BD1 BD D01 SCD14 100R R44 100R R45 nRESET 2 Vss 1 Vcc 3 U02 STM809 510 R47 Q02 8050S Q03 8050S Q01 8050S 510 R48 20k R49 47k R50 47k R51 1 2 3 CON2 Header 3 link1 link1 VCC 1 2 CON4 Header 2 47k R52 Q04 8550S 0.22u C22 10u C30 10u C28 10u C25 10u C26 33R R37
27、 470u/16V C33 100n C24 1 2 3 4 5 CON3 Header 5 AGNDAGND VSS VSS VSS open C34 open C35 open C36 open C37 open C38 open C39 GND open C40 open C41 GND GNDGND CUSTOMER:JBL MODEL:SB 15SUB/230 DETA:SEP.01.2009 PREPAREDCHECKEDCHECKEDAPPROVEDREV 1.0 PAGE3/5 BOARD: WIRLESS GND rest rest harman/kardonSB 16/23
28、0 Service Manual Page 9 of 29 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 DD CC BB AA 6800u/35v C24 22u/35v C40 DZ2 6800u/35v C43 100/2W R08 Q02 D882 100/2W R22 22u/35v C36 22n C38 22n C42 Q04 B772 220u/25v C30 220u/25v C44 VCC VSS +15v -15v 1 1 2 2 3 3 CON4 -15v +15v VCC VSS IN1+ 8 IN2+ 5 IN2- 4 VDDA1 10 OSC 7
29、 MODE 6 VDDP1 14 VDDP2 23 BOOT1 15 OUT1 16 BOOT2 22 VSSP1 17 OUT2 21 IN1- 9 VDDA2 3 VSSD 24 STABI 18 VSSP2 20 VSSA1 12 VSSA2 1 PROT 13 N.C. 19 SGND1 11 SGND2 2 U1 TDA892XBTH L02 33uH L01 33uH MODE VDDA2VSSA2VDDPVSSP VDDPVSSPVSSP VDDPVSSP VDDPVSSP 47u/100v C11 470u/35v C01 470u/35v C03 SUB VDDA2VSSA2
30、 VDDA2VSSA2 220u/25V C09 10K R04 5.6V DZ1 D01 1N4148 470u/35v C08 470u C02 VDDP VCC VSSP VSS 30.1k R05 24k R03 MODE 100n C12 100n C17 100n C16 100n C19 100n C15 100n C18 100n C50 100n C57 100n C56100n C51 100n C52 100n C58 1u C26 1u C20 1n C23 1n C25 220p C53 470p C60 470p C59 470p C13 470p C14 15n
31、C39 15n C27 100n C07 100n C06 100n C05 100n C04 2.2u C10 5.6k R14 5.6k R10 0R R21 30.1K R06 10R R19 10R R07 10R R02 10R R01 4.7K R11 4.7K R20 680R R12 680R R18 1.3K R15 15K R09 15K R16 1 2 3 4 5 6 CON1 Header 6 +3.6V std 1 2 3 4 5 CON2 Header 5 +15v -15v SUB 12 BD1 BD 12 BD2 BD Q06 8550S VCC BR1 Bri
32、dge1 100n C34 100n C21 1n C22 100n C31 100n C54 100n C48 100n C35 100n C41 Q03 8050S SGND SGND VSSA2 C45 120n/63V C28 120n/63V R17 22R R13 22R 1 2 CON3 CON2 SUBOUT+ SUBOUT- C29 470n/63V C49 470n/63V 330p C32 330p C46 12 BD6 BD 12 BD4 BD 100n C55 6.8n C61 100n C33 6.8n C62 330p C63 R23 2R2 R24 2R2 33
33、0p C64 2.2n C65 2.2n C66 D02 1N4148 CUSTOMER:JBL MODEL:SB 15SUB/230 DETA:SEP.01.2009 PREPAREDCHECKEDCHECKEDAPPROVEDREV 1.0 PAGE4/5 BOARD: POWER AMP harman/kardonSB 16/230 Service Manual Page 10 of 29 1 1 2 2 3 3 4 4 DD CC BB AA 0.22u C07 12 34 L02 8mH RV1 14D471K TRANSFORMER 10n C16 0R R18 GND 4.7k
34、R13 D01 1N4007 D04 1N4007 D03 1N4007 D06 1N4007 15uf/400V C01 470PF/1k C08 OB 1 VCC 2 GND 3 CT 4 FB 5 IS 6 OC 7 OC 8 U02 THX203H 47uF/16V C13 680P C15 1 2 4 3 op1 PC817C 4.42K R08 10k R14 510 R07 0.1u C17 10k R09 10k R06 21 3 U01 ST TL431 330pF C03 300k R02 1.1meg R03 1.1meg R04 2R R12 0.1u/25V C12
35、D05 UF1010 22n C18 100K R05 HI VOL ICSP GND GND std 2R R11 300k R01 680R R17 100k R10 0R R15 D07 SF16 std +3.6V 1 2 CON3 Header 2B 1 2 CON2 Header 2B +12VB Q02 8050S 470u/16V C04 22uH L1 Inductor 470u/16V C05 D02 UF302 GND +3.6V 0.1u C09 0.1u C11 D08 1N4148 1 2 3 CON1 Header 3 K1 Relay-SPST GND N_IN
36、 L_OUT L_IN 0R R21 GND AK LED1 GND 0R R16 Q03 8050S Q01 8050S HI OPERATIVE LOW OPERATIVE OPEN:R05,Q01,R13,R18 OPEN:R15,R16 +12VB +3.6VA 2 3 4 5 1 W1 W2 W3 6 7 W4 S1 S2 6 8 TR1 TR D09 UF302 100u/25V C06 0.1u C10 GND +3.6VA 1000p C19 1000p C20 GND CUSTOMER:JBL MODEL:SB 15SUB/230 DETA:SEP.01.2009 PREPA
37、REDCHECKEDCHECKEDAPPROVEDREV 1.0 PAGE5/5 BOARD: STANDBY POWER 68 ohm R19 open R20 open R22 100k R23 GND +12VA harman/kardonSB 16/230 Service Manual Page 11 of 29 Because the design itself, once disassembling the system, the top bottom trim panels snap points will break and new trim panel has to be r
38、eplaced 1 Check the cabinetCheck the baffleAttach protective film on the rear cabinet 2 Attach EVA foam gasketattach EVA foam gasket 3 load woofer ( screw PN 352-AM04008C1334-E X 16 pcs ) 4 load tweeteradd adhesivesattach tweeter bar and screw down screw pn 352-AM03008C1086-E 5 left chan Xover (P/N
39、013-7600-05766-E) right chan xover (P/N 013-7600-05766-1E)Screw PN 352-AM03008C1086-E harman/kardonSB 16/230 Service Manual Page 12 of 29 ASSEMBLY AND DISASSEMBLY, SB 16 SOUNDBAR. 6 Plug green/black cables to the woofer, green cable for + polarity, and black for - polarityplug blue cable to tweeter
40、+, and black to tweeter - 7 Apply adhesivesAssemble knobs/LEDsScrew PN 352-AM03008C1086-E X 1 pcs 8 Assemble AmpScrew down amp ( Screw X 9 pcs PN: 352-AM03008C1086-E ) black/red cables on crossovers to be pulled inward the amplifier harman/kardonSB 16/230 Service Manual Page 13 of 29 9 load in insul
41、ation X 2 pcs 10 plug in xover harness to the ampplug in button.key harnessleft channel crossover right channel crossover 11 attach baffle to rear enclosurescrw PN 352-AM03510D112-E X 20 pcs 圖1 harman/kardonSB 16/230 Service Manual Page 14 of 29 12 apply adhesivespress in the grille 13 Snap in the t
42、op gloss trim panelsnap in the bottom gloss trim panel 14 attach the side end cap ( peel off adhesive ) and add super glueattach the end cap to the cabinet harman/kardonSB 16/230 Service Manual Page 15 of 29 Active speaker soundbar SB 16/230 Owners Manual 0243CSK - HK SB16 230V OM v6.indd 107/10/10
43、15:59:00 harman/kardonSB 16/230 Service Manual Page 16 of 29 SB 16/230 2 Table of Contents IntroductIon 3 descrIptIon and Features 3 Included Items 3 soundbar top-panel controls 4 soundbar rear-panel controls and connectIons 4 subwooFer rear-panel controls 5 speaker placement 6 placIng the soundbar
44、on a table 6 wall-mountIng the soundbar 6 placIng the subwooFer 6 connectIons 7 source connectIons 7 power connectIons 8 operatIon 9 turnIng the soundbar on and oFF 9 turnIng the subwooFer on and oFF 9 adjustIng the systems Volume 9 mutIng the system 9 soundbar surround mode button 9 soundbar src (s
45、ource) button 9 subwooFer Volume knob 10 soundbar trIm swItch 10 wIreless code swItches 10 subwooFer crossoVer knob 10 subwooFer phase swItch 10 programmIng the soundbar to respond to your tV remote 11 troubleshootIng 12 specIFIcatIons 13 0243CSK - HK SB16 230V OM v6.indd 207/10/10 15:59:00 harman/k
46、ardonSB 16/230 Service Manual Page 17 of 29 Introduction, Description and Features, Included Items 3 SB 16/230 Introduction please register your product on our web site at . note: youll need the products serial number. at the same time, you can choose to be notified about our new products and/or spe
47、cial promotions. thank you for purchasing the harman kardon sb 16/230 speaker system, with which youre about to begin many years of listening enjoyment. the sb 16/230 has been custom-designed to provide the excitement and power of the cinema experience in your own living room. while sophisticated el
48、ectronics and state-of-the-art speaker components are hard at work within the sb 16/230, hookup and operation are simple. to obtain maximum enjoyment from your new soundbar speaker system, we urge you to take a few minutes to read through this manual. this will help ensure that the connections you m
49、ake are correct. In addition, a few minutes spent learning the functions of the various controls will enable you to take advantage of all the power and refinement the sb 16/230 is able to deliver. If you have any questions about this product, its installation or its operation, please con- tact your retailer or custom installer, or visit our web site at . Description and Features the sb 16/230 is a complete home theater speaker system that includes: a video-shielded stereo soundbar speake