JBL-SCS180.6S-av-sm维修电路原理图.pdf

《JBL-SCS180.6S-av-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JBL-SCS180.6S-av-sm维修电路原理图.pdf（27页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Surround Cinema Series Models: SCS150SI SCS160SI SCS180.6S SCS150SI SCS160SI SCS180.6S Home Theater Speaker Systems SERVICE MANUAL JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev4 10/2005 RadioFans.CN - CONTENTS - BASIC SPECIFICATIONS.1 DETAILED SPECIFICATIONS .2 CONNECTIO

2、NS .3 OPERATION. 6 BASIC TROUBLESHOOTING.7 EXPLODED VIEW.8 TEST SET-UP AND PROCEDURE.9 PCB DRAWINGS .10 MECHANICAL/SATELLITE PARTS LIST16 ELECTRICAL PARTS LIST .17 IC/TRANSISTOR PINOUTS.22 SCHEMATICS .23 PACKING.26 SCS150SI/SCS160SI/SCS180.6S Systems Frequency Response 30Hz 20kHz (6dB) Satellites Re

3、commended Power 10 100 watts Impedance 8 ohms nominal Sensitivity 88dB 1 watt/1 meter Tweeter One 1/2 (13mm) titanium laminate dome, video-shielded Midrange Dual 3 (75mm) drivers, video- shielded Dimensions (H x W x D) 8-1/8 x 3-1/2 x 3-7/8 (206mm x 89mm x 99mm) Weight 2.65lb/1.2kg Center Recommende

4、d Power 10 100 watts Impedance 8 ohms nominal Sensitivity 88dB 1 watt/1 meter Tweeter One 1/2 (13mm) titanium laminate dome, video-shielded Midrange Dual 3 (75mm) drivers, video- shielded Dimensions (H x W x D) 3-1/2 x 8-1/8 x 3-7/8 (89mm x 206mm x 99mm) Weight 2.65lb/1.2kg Subwoofer Amplifier 150 w

5、atts RMS Woofer 10 (254mm) woofer, bass-reflex enclosure Dimensions (H x W x D) 17-3/4 x 15-3/4 x 16-3/4 (451mm x 400mm x 426mm) Weight 35 lb/15.9kg Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated S

6、CS150SI/SCS160SI/SCS180.6S SCS150SI/SCS160SI/SCS180.6S RadioFans.CN 150W Powered Sub/ Plate Amp LINE VOLTAGEYes/NoHi/Lo LineUnitNotes US 120vac/60HzYes108-132VrmsNormal Operation Asia 100vac/50HzYes90-110VrmsNormal Operation ParameterSpecificationUnitQA Test LimitsConditionsNotes Amp Section Type (C

7、lass AB, D, other)D D n/a Load Impedance (speaker)4 Ohmsn/aNominal Rated Output Power150 Watts1451 input driven THD Rated Power0.08 %122k filter THD 1 Watt0.1 %0.522k filter DC Offset10 mV-DC20 Speaker Outputs Damping factor100 DF30 Measured at speaker terminals, Output power 140 Watts THD 0.1 % Inp

8、ut Sensitivity Input Frequency50 Hz50Nominal Freq.1 input driven Line Input (L then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with banana-type connectors. SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 3 Dolby*Pro Logic*(No

9、n-Digital) Speaker Level Use this installation method for Dolby Pro Logic appli- cations (not Dolby Digital, DTSor other digital processing), where the receiver/processor does not have a subwoofer output, or a volume-controlled preamp (line-) level output: Connect your receiver or amplifiers front l

10、eft and right speaker terminals to the left and right terminals on the subwoofer that are marked “High Level In.” Connect the left and right terminals on the subwoofer that are marked “High Level Out” to the cor- responding terminals on the back of your front left and right speakers. Connect your re

11、ceiver or amplifiers center, left and right surround-speaker terminals to the corre- sponding terminals on the back of your center, left and right surround speakers. Right Front Right Surround Left Front Left Surround Center + + + + + + + Left FrontCenter + Left Surround Right Front + Right Surround

12、 + Subwoofer Receiver HIGH LEVEL + + L R OUT IN SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 4 Dolby Pro Logic (Non-Digital) Line Level Use this installation method for Dolby Pro Logic appli- cations (not Dolby Digital, DTS or other digital processing), where the receiver/processor is equi

13、pped with a subwoofer output, or a volume-controlled preamp (line-) level output: Use RCA-type patch cords to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs on the subwoofer. IMPORTANT: Do not use the LFE input on the subwoofer with Dolby Pro Logic pr

14、ocessors. Note: If your receiver or amplifier only has one subwoofer output jack, then you will need to use a Y-connector (not included). Plug the male end of the Y- connector into your receiver or amplifiers subwoofer output jack, and connect each of the two female ends to separate RCA-type patch c

15、ords. Finally, plug the RCA- type patch cords into the line- level inputs on the subwoofer. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure your receiver or processor is correctly configured to indicate that the subwoofer is “On.” Note for advance

16、d users: If your receiver/processor has a built-in low-pass crossover filter for the subwoofer output, you may use the LFE input to bypass the subwoofers internal crossover. Use this installation method for Dolby Digital, DTS or other digital surround processors: Use the line-level input jack marked

17、 “LFE” for the Low- Frequency Effects channel. Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround- sound processor for “Subw

18、oofer On.” The front left, front right, center and rear speakers should all be set to “Small.” Dolby Digital or DTS (or Other Digital Surround Mode) Connection LINE LEVEL IN LFE INPUTLFE OUT L R SUBWOOFERRECEIVER + + + + + + + + + + Receiver Subwoofer Out Left Front Left Rear Right Front Right Rear

19、Subwoofer R L R L Center Line- Level In Right Surround Right Front Left Surround Left Front Center SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 5 OPERATION MIN MAX Subwoofer Level MIN MAX Subwoofer Level Move the Master Power switch (marked “Power” ) to the “” (On) position to use the subw

20、oofer. The subwoofer will automatically turn itself on or go into standby (sleep) mode when left in the standby mode (“Auto/On” switch in the “Auto” position). When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in standby mode. When the

21、 sub- woofer senses an audio signal, it will automatically turn itself on. If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go into standby mode. When the “Auto/On” switch is switched to the “On” position, the subwoofer will remain on, whether or not

22、 program material is playing. If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power switch to the Off position. Volume POWER HIGH LEVEL + + SUBWOOFER LEVEL OUT IN L R LINE LEVEL IN LFE L R AUTO ON MIN MAX AC 120V60Hz 250 Watts 3.1

23、5A/250V TYPE T IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL. GREEN: ON RED: STANDBY + AVIS : RISQUE DE CHOC LECTRIQUE-NE PAS OUVRIR WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 3.15A, 250 VOLT FUSE AVERTISSEMENT: UTILISEZ UN FUSIBLE DE RECHANGE D

24、E MEME TYPE 3.15A, 250V A Harman International Company JBL, Incorporated This area is designed to become quite warm during normal operation CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMEN

25、T: POUR PRVENIR LES RISQUES DINCENDIE OU DE CHOC LECTRIQUE, VITER DEXPOSER CET APPAREIL A LA PLUIE OU A LHUMIDIT. Volume can be adjusted using the Subwoofer Level Control (above), as shown below. SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 6 If there is no sound from any of the speakers:

26、Check that receiver/amplifier is on and a source is playing. Check that the powered subwoofer is plugged in, and itsPower switch is switched on to the “” position. Check all wires and con- nections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the spe

27、aker wires are frayed, cut or punctured. Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: Check the “Balance” control on your receiver/amplifier. Check all wires and con- nections between receiver/ amplifier and speakers. Make sure all wires are conne

28、cted. Make sure none of the speaker wires are frayed, cut or punctured. In Dolby Digital or DTS modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. Turn off all electronics and switch the speaker in question with one of the other speakers that is wo

29、rking correctly. Turn everything back on, and determine whether the problem is in the same place, i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i.e., the speaker that was not working still has no sound an

30、d the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manual for that product for further information.If the problem has followed the speaker, consult your dealer

31、for further assistance or, if that is not possible, visit our Web site at for further information. If there is no sound from the center speaker: Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed,

32、cut or punctured. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is con- figured so that the center speaker is enabled. If the system play

33、s at low volumes but shuts off as volume is increased: Check all wires and con- nections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If more than one pair of main speakers is being used, check the mini

34、mum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: Make sure the connections to the left and right “Speaker Inputs” have the correct polarity (+ and ). Make sure the subwoofer is plugged into an active electrical outlet. Make sure the powered subwoofer is plu

35、gged in, and itsPower switch is switched on to the “” position. TROUBLESHOOTING In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled. SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 7 SUB150/160/180 EXPLODED VIEW Ref#

36、Description Part Number Qty 1 SUB150/160/180 CABINET NOT FOR SALE 1 2 FOOT MAIN PLASTIC BODY (SCS150SI) WI5447 4 “ (SCS160SI) 321-ABS-00008 4 “ (SCS180.6) 321-ABS-00008-0LA 4 3 FOOT RUBBER BOTTOM (SCS150SI) WI5448 4 “ (SCS160SI/180.6) 321-ABS-00009 4 4 FOOT SCREW T4*30L 06-T43005 4 5 10” WOOFER 25MF

37、12DZB-DW02 1 6 AMPLIFIER/WOOFER SCREWS T4*20L 06-T4205012 15 7 SUB150/160/180 AMPLIFIER NOT FOR SALE 1 8 Test Set Up and Procedure Equipment needed: Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables General Unit Function (UUT = Unit Under Test) 1) From the sign

38、al generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single LFE input. 2) Turn on generator; adjust to 100mV, 50 Hz. 3) Plug in UUT; turn the power switc

39、h ON. LED should switch from Red to Green. Turn LEVEL control full clockwise (MAX) 4) LED should Green; immediate and vigorous bass response should be heard and felt from port tube opening. 5) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 6) Connect on

40、e pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 7) Turn on generator and adjust so that speaker level input at the amplifier is 2.0V, 50 Hz. Turn LEVEL control full clockwise. 8) Green LED should

41、 light; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 6-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any othe

42、r noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.4 ohms 10% 3) Connect a pair of speaker cables to driver terminals. C

43、ables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises. SCS150SI/SCS160SI/SCS180.6S SCS150SI/SCS160SI/S

44、CS180.6S 9 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 10 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 11 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 12 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 13 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 14

45、 SCS150SI/SCS160SI/SCS180.6SSCS150SI/SCS160SI/SCS180.6S 15 SCS150SI/SCS160SI/SCS180.6S Mechanical/Satellite Parts List Description SCS150SI SCS160SI SCS180.6S SUBWOOFER Amplifier Assy Not for Sale Not for Sale Not for Sale SUB 150/SUB160/SUB180 Cabinet Not for Sale Not for Sale Not for Sale 10” Woof

46、er DCR = 3.4 ohms 10% 25MF12DZB-DW02 25MF12DZB-DW02 25MF12DZB-DW02 Rubber Foot Pad wi5448 321-ABS-00009 321-ABS-00009 Foot wi5447 321-ABS-00008 321-ABS-00008-0LA SATELLITES Complete SCS150SI/SAT-1 SCS160SI/SAT-1 SCS180.6S SAT-1 Woofer 32PF55JE-LW02 32PF55JE-LW02 32PF55JE-LW02 Tweeter 29DM15NA-FT03 2

47、9DM15NA-FT03 29DM15NA-FT05 (Front baffle w/Tweeter) Foot wi5213-g 325-000-00151 320-RUB-00025-0LA (Rear) 320-RUB-00053-0LA (Front) Grille xc035006 244-030-00083 244-030-05043-0VA X-over Network xr5138-1 013-AA00-00296 013-AA00-00296 Enclosure 306-ABS-00124 Front baffle 243-030-00323 Wall bracket wi0

48、408 372-000-00042 372-000-00042 Support mural wi0409 325-FE-00163 325-FE-00163 CENTER CHANNEL Complete SCS150SI/CENTER-1 SCS160SI/CENTER-1 SCS180.6S CEN-1 Woofer 32PF55JE-LW02 32PF55JE-LW02 32PF55JE-LW02 Tweeter 29DM15NA-FT03 29DM15NA-FT03 29DM15NA-FT05 Foot wi5213-g 325-000-00151 320-RUB-00053-0LA Grille xc035007 244-030-00084 244-030-05044-0VA X-over Network xr5138-1 01