Pass-Aleph3-pwr-sm维修电路原理图.pdf

《Pass-Aleph3-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Pass-Aleph3-pwr-sm维修电路原理图.pdf（11页珍藏版）》请在收音机爱好者资料库上搜索。

1、Pass Laboratories Aleph 3 Service Manual rev 02/1/96 Aleph 3 Service Manual. The Aleph 3 is a stereo 30 watt per channel audio power amplifier which operates in single-ended class A mode. The Aleph 3 has only two gain stages which are biased by current sources. Because of the inherent simplicity of

2、the circuit, it is easy to understand and repair. There are no adjustments. Figure 1 shows the simplified schematic of the amplifier. Two p channel Mosfets form an input differential pair biased by a current source operating at about 20 ma. The drain of the input Mosfet is attached to the gate of an

3、 n channel power Mosfet which forms the active output stage. It is biased by a current source at slightly greater than 2 amps. The voltage rails of the supply are at 25 volts, and each channel draws approximately 100 watts. Figure 2 shows the actual schematic for the power supply and one channel. F1

4、 is a slow blow fuse, set at 4 amps for 100-120 volt operation, and 2 amps for 220-240 volt operation. S1 is the power switch, which has two sets of 25 amp contacts wire in parallel. T1 is a thermostatic switch rated at 75 degrees Centigrade. It is mounted to the rear heat sink. TH1 is a power therm

5、istor used to connect the circuit and chassis ground to the AC outlet ground. It will normally operate at 5 ohms, suppressing ground loops in the system, but will drop to a low impedance if significant current is passed through it. RadioFans.CN 收音机爱 好者资料库 TH2 is a power thermistor (Keystone CL-60) w

6、hich is used to suppress inrush current. The power transformer drives a high current bridge and 170,000 uF of capacitance to form a plus and minus 25 volt supply. Referring to the channel itself, Q101 and Q102 form the differential input pair of Mosfets. They are biased by the current source formed

7、by Q103. Q103 is biased to about 20 ma by the reference Zener diode Z103 which sets about 5 volts across R106. Z101 and Z102 protect the input from static spikes. R101-104 form the input networks and feedback loops. The output of the differential input paid drives the gates of output devices Q108 an

8、d Q109. These parallel devices are matched as close as .01 volts, however variations as high as .1 volts will not impede operation. The voltage across R108 shows the drive voltage for the output stage, and it should have 4-5 volts across it. The output of the amplifier is taken from the drains of Q1

9、08 and Q109. Q108 and Q109 are provided a bias current by the current source circuitry of Q106 and Q107, also a matched pair of n channel Mosfets. Q106 and Q107 are set at 2 amps DC by the network consisting of Q105 and the components surrounding it. Q105 is biased by R111 and R112 in series. A capa

10、citor C103 is used to reduce supply noise. R115 serves to sense the current running through Q106, and feeds that to the base of Q105, forming a loop that holds the output current at 2 amps. The pn junction drop of Q105 forms the reference voltage for the system. R113 is a fixed resistor which trims

11、the DC current value. R114 and C103 adjust the current against output current as sensed by the voltage across R124-127. Fig. 3 shows the component layout of the central circuit board. This board holds the power supply components and connects the power stages together. On this diagram you can see the

12、 wiring arrangements for the various AC line voltages: 100, 120, and 240 volts. The two large pads at either side of the AC wiring area have a black and white wire going back to the AC input system. The black wire is hot AC, and the white is cold AC. The pads between these go to the transformer prim

13、aries. Fig 4 and 5 show the component layout of the board assembly forming the input stage and the active (negative) portion of the output stage. Fig 6 and 7 show the component layout of the board assembly forming the positive half of the output stage, the current source. RadioFans.CN 收音机爱 好者资料库 The

14、re are no adjustments to the amplifier. Values for biasing various components are taken from physical constants, such as pn junctions and zener voltages, and through matching of Mosfet transistors. The input Mosfets are matched Vgs to within .01 volts, and the output Mosfets are in matched pairs wit

15、hin .1 volt, although production tolerance is typically .01 volt. For a 120 volts AC line, the amplifier will draw about 2 amps RMS. If you measure current draw with an averaging meter, you will get a smaller number. The amplifier is designed so that the heat sinks will operate approximately 25 degr

16、ees C. above ambient, for a typical temperature of 50 degrees C. Temperature protection occurs at 75 degrees C. The amplifier will not be damaged by driving a short circuit, and it is probable that the only failures you will see will be random component failure. SPECIFICATIONS Gain20 dB Freq. Respon

17、se- 0.5 dB at 2 Hz, 100 KHz Power Output30 watts/ch8 ohms 60 watts/ch4 ohms 60 watts/ch2 ohms Maximum Output23 volts, 8 amps Distortion (1KHz)0.2% 30 watts, 8 ohms 1% 60 watts, 4 ohms 1% 60 watts, 2 ohms Input Impedance23 Kohm Damping factor100 Crosstalk -80 dB20-20 KHz Output Noise500 uV unweighted

18、 DC offset 100 mv Power Consumption250 watts Temperature25 degrees C. above ambient RadioFans.CN 收音机爱 好者资料库 Dimensions12 W x 12 D x 6 H Shipping Weight38 lb. PASS Pass Laboratories 21555 Limestone Foresthill CA 95631 tel(916) 367 3690 fax(916) 367 2193 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库