Akai-MPC4000-mpc-sm维修电路原理图.pdf

《Akai-MPC4000-mpc-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Akai-MPC4000-mpc-sm维修电路原理图.pdf（9页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库 OS Update procedure for MPC4000 The OS update can be made from PC via the USB port. You must have the OS loader software for MPC4000, besides the OS bin file. OS loader software contains OS Loader.exe file, USB driver.inf file, and USB Driver.sys file. 1. Install USB driver t

2、o your PC After unZipped, place the USB Driver.inf and USB Driver.sys files to the same folder, e.g. Driver. Turn the PC and MPC4000 on. Then connect the sampler to the PC via USB cable. This prompts that the PC found the new device and requires the new driver. Refer to the Driver folder you just cr

3、eated. Then the driver is placed properly and the MPC4000 is recognized. 2. OS update Double click on the OS Loader.exe icon and specify the OS bin file. It will send the OS to the MPC4000. Caution After update, be sure to initialize the MPC4000 by pressing GLOBAL Key, then F6 INITIAL and F5 DO IT,

4、before turning it off. OS update procedure from removable media (CD-ROM, Zip, MO) To update OS from CD-ROM, it requires OS version later than V1.02 software on MPC4000, and to update OS from removable media (Zip, MO), it requires OS version later than V1.10 software. You can update the OS from the r

5、emovable media. Please use a disk that contains the OS for the MPC4000. You can create the OS disk by using your PCs to write the MPC4000.bin file on to disk. 1. Turn the MPC4000 on and insert the OS disk. 2. Press the LOAD button, then select MPC4000 OS file (.bin file). 3. Press F6 DO IT, then the

6、 F6 INSTALL button. 4. Displayed OS Upgrade, please wait . then Upgrading of the Flash ROM was successful. 5. Press F6 Restart button, be sure to initialize the MPC4000 by pressing GLOBAL Key, then F6 INITIAL and F5 DO IT, before turning it off. RadioFans.CN 收音机爱 好者资料库 Check the included items 251 A

7、ppendix: Installing storage devices (for service engineers) This appendix explains how to install storage devices (ATA hard disk, CD-ROM drive, Zip drive, etc.) in the MPC4000. Check the included items The following items are included with the MPC4000 for use when installing storage devices. Check t

8、o make sure that no items are missing. I Cables Flat cable for ATA drive Power cable for drive (without ferrite core) Power cable for drive (with ferrite core) Analog audio cable for CD-ROM Digital audio cable for CD-ROM I Other items Screws (inch) for attaching hard disk (4 pcs.) Screws (metric) fo

9、r attaching hard disk (4 pcs.) Screw hole plugs (4 pcs.) Opening the top panel When installing a storage device, use the following procedure to open the top panel of the MPC4000. 1.Loosen the screws that fasten the side panels (four on each side, left and right), and remove the side panels. 2.Remove

10、 the screws (five on each side, left and right) that fasten each side of the top panel to the chassis. Appendix: Installing storage devices (for service engineers) 252 3.Remove the screw (located in the center of the front panel) that fastens the top panel from the lower front side. 4.Remove the scr

11、ew (located in the center of rear panel) that fastens the top panel from the rear side. 5.Use both hands to lift the protrusion on the front of the top panel, and open the top panel. Installing a drive 253 6.Use a metal rod or similar object as a prop inside the chassis to hold up the top panel. The

12、 side panels and screws you removed must be kept in a safe place. To close the top panel, re-tighten the screws in the opposite order to which they were removed. Installing a drive 1.If you are installing a removable-media drive such as a CD-ROM drive or Zip drive, remove the blank panel from the fr

13、ont panel. 2.Detach the bracket that is attached to the bottom panel of the chassis. 3.Use the hard disk attachment screws (included with the MPC4000) to attach the drive to the bracket, and re-attach the bracket to the bottom panel of the chassis. When installing a drive in the 3.5 inch bay P2 P7 P

14、8 PC IO PC CPU PC IO AD_DA Appendix: Installing storage devices (for service engineers) 254 When installing a drive in the 5 inch bay Cable connections Connecting the fl at cable 1.Remove two screws from the cover that conceals the PC CPU board. When you remove the cover, you will see the P2 connect

15、or for the ATA drive. 2.3Insert the blue connector of the included flat cable into the P2 connector of the PC CPU board. 3.Reattach the cover that you removed. 4.Connect the other end of the flat cable to the drive. P7 P8 P2 P23 PC IO PC CPU PC IO AD_DA P2 P7 P8 PC IO PC CPU PC IO AD_DA Step 1 Cable

16、 connections 255 Connecting the power cable 1.Insert the connector of the included power cable into the P7 connector or P8 connector of the PC I/O board. Use the power cable with the ferrite core if you are installing a hard disk. Use the power cable without a ferrite core if you are installing a Zi

17、p drive or CD-ROM drive. 2.Connect the other end of the power cable to the drive. Connecting the CD-ROM analog audio cable If the CD-ROM drive has an analog audio output connector, connect it to the MPC4000s circuit board as follows. 1.Insert the connector of the included CD-ROM analog audio cable i

18、nto the P23 connector of the PC I/O ADDA board. 2.Insert the other end of the CD-ROM analog audio cable into the analog audio output connector of the CD-ROM drive. Make connections so that the red cable goes to R (right channel) and the white cable to L (left channel). 3.On the PC I/O ADDA board, pl

19、ug in the P22 jumper (located in front of P23) at the “SET” position. Connecting the CD-ROM digital audio cable If the IB-4D digital I/O option is installed in the MPC4000, connect the digital audio out- put connector of the CD-ROM drive to the IB-4D as follows. 1.Insert the connector of the include

20、d CD-ROM digital audio cable into the digital audio output connector of the CD-ROM drive. Make connections so that the black cable is the ground. 2.Insert the other end of the CD-ROM digital audio cable into the P1 connector of the IB-4D digital I/O option. 3.On the IB-4D circuit board, plug in the

21、JP1 jumper in the 1-2 (SHORT) position. * If you connect the analog/digital audio cable and make the correct jumper setting, you will be able to select the CD-ROM playback as the recording source in RECORD mode. Master/slave settings for ATA drives If you install two drives, you must set one as the master and the other as the slave. (If a hard disk is installed, set the hard disk as the master.) For details on how to make master/slave settings, refer to the manual that came with your drive.