JVC-MXGC5-cs-sm维修电路原理图.pdf

《JVC-MXGC5-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXGC5-cs-sm维修电路原理图.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、MX-GC5 MX-GC5 Contents COPYRIGHT 2005 Victor Company of Japan,Limited Safety precautions - 1- 2 Preventing static electricity - 1- 3 Important for laser products - 1- 4 Disassembly method - 1- 5 Adjustment method - 1- 18 Flow of functional operation until TOC read - 1- 20 Maintenance of laser pickup

2、 - 1- 21 Replacement of laser pickup - 1- 21 Description of major ICs - 1- 22 SERVICE MANUAL COMPACT COMPONENT SYSTEM Area Suffix J . U.S.A. C . Canada SP-MXGC5SP-MXGC5CA-MXGC5 RadioFans.CN 收音机爱 好者资料库 Warning ! CAUTION Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Havi

3、ng 1000 ohms/v 1500 10W olts, or more sensitivity) 0.15 F AC TYPE Safety Precautions 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized i

4、n writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only. 2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made.

5、Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. 3. Many electrical and mechanical parts in the products have special safety-related characteristics. These c

6、haracteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Se

7、rvice Manual. Electrical components having such features are identified by shading on the schematics and by ( ! ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts L

8、ist of Service Manual may create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire

9、 hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard testing) After re-assembling the product, always perform an isolation c

10、heck on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a line isolation transformer during this check. ? Plug the AC line cord

11、 directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.) ? Alter

12、nate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC- type capacitor between an exposed metal part and a known good earth ground. Measur

13、e the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measure

14、ment. Voltage measured Any must not exceed 0.75 V AC(r.m.s.). This corresponds to 0.5 mA AC(r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards. 2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained. 3.

15、 Repairs must be made in accordance with the relevant safety standards. 4. It is essential that safety critical components are replaced by approved parts. 5. If mains voltage selector is provided, check setting for local voltage. Burrs formed during molding may be left over on some parts of the chas

16、sis. Therefore, pay attention to such burrs in the case of preforming repair of this system. RadioFans.CN 收音机爱 好者资料库 Preventing static electricity 1. Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc.

17、 is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 2. About the earth processing for the destruction prevention by static electricity In the equipment which uses optical pick-up (laser diode), optical pick-up is destr

18、oyed by the static electricity of the work environment. Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit

19、 (optical pickup) on it. 2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup 1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical picku

20、p are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) 2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 4. Handling the CD changer unit (

21、optical pickup) 1. Do not subject the CD changer unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text.

22、 Remove the anti-static pin when replacing the CD changer unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the l

23、aser power. Do not turn it. Attention when traverse unit is decomposed * Please refer to “Disassembly method” in the text for pick up and how to detach the CD changer mechanism. 1. Remove the CD changer unit. 2. Disconnect the harness from connector on the CD motor board. 3. Solder is put up before

24、the card wire is removed from connector Cn601on the main board as shown in Fig.A and Fig. B. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.) 4. Please remove solder after connecting the card wire with CN601 when you install picking up in the substrate. Co

25、nductive material (conductive sheet) or iron plate (caption) Anti-static wrist strap Soldering Fig.B Flexible cable Fig.A CD changer unit 1. CLASS 1 LASER PRODUCT 2. DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3. CAUTION : There are

26、no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4. CAUTION : The compact disc player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and

27、the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. Important for laser products FUSE CAUTION CAUTION: REPLACE WITH SAME TYPE AND RATING FUSE (S). ATTENTION: REMPLACER PAR UN(LES) FUSIBLE(S) DE MEME TYPE ET DE MEME VALEUR 5. CAUTION : If safety switches

28、malfunction, the laser is able to function. 6. CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ! CAUTION Please use enough caution not to see the beam directly or touch it in case of an adjustment or op

29、eration check. Disassembly method Commence disassembly of the set by removing the main units and then proceed to the components and assemblies inside the units. Replacement of the fuses and the power IC ? Top cover ? CD changer unit ? Front panel assembly ? CD changer unit ? Removing the main PCB ?

30、Removing the CD changer mechanism assembly ? Removing the CD pickup ? Replacing the loading motor and belt of the CD changer tray ? Replacing the CD tray rotor belt of CD changer, and removing the motor ? Front panel assembly ? Removing the (USB, AUX jack) earphone jack PCB ? Removing the control/FL

31、 PCB ? Removing the volume, preset and CD Function switch PCB ? Removing the remote sensor PCB ? Removing the standby Led PCB ? Removing jack Led backlight PCB ? Removing Sound mode PCB 1-5 Replacement of the fuses and the power IC ? Replacing the fuses (See Fig.1) ? Prior to performing the followin

32、g procedure, remove the left side BOARD. 1. Replace the fuses inside. Caution Be sure to use fuses with the specified ratings. ? Replacing the heat sink cover (See Fig.3) 1. Remove four screws B from the rear panel. 2. Remove four screws E from the heat cover. 3. Pull the heat sink cover outward. ?

33、Replacing the power IC (See Fig.2) ? Prior to performing the following procedure, remove the top cover. 1. Remove the two screws A from the heat sink between the power IC(STK412-430) 2. Remove the four screws B from the heat sink the between the power IC (D1889,B1340) 3. Remove the solder fixing the

34、 power IC. AA Fig.2 Fig.1 Fig.3 B E Fuse (F901) 3.5A 125V Fuse (F902) 1.6A 250V B Fig.5 ? Removing the top cover (See Fig.4 and 5) 1. Remove six screws C that retain the top cover from the panel rear of the body. 2. Remove six screws D that retain the top cover from the two sides of the body. 3. Rem

35、ove the top cover from the body by lifting it toward the rear. Top cover Fig.4 Right Front panel assemblyLeft Front panel assembly DD D D Fig.6 Fig.9 ? Removing the CD changer unit (See Fig.6 to 9) ? Prior to performing the following procedures, remove the top cover. Caution Although the CD mechanis

36、m unit can be removed without removing the CD tray panel, it is still recommended to remove it in order to prevent damage. a. From the front panel side of this set, push in the sections marked with arrows and pull out the CD tray toward the front. b. Remove the CD tray panel by pushing both of its e

37、xtremities upward in the direction of the arrows. c. Push the CD tray deep into the set. 1.Disconnect the cord wires from the main PCB CN401,CN601,CN501 and CN203. 2. From the rear of the set, remove two screws E, two screws F and four screws G on the front panel left and right side. 3. Handle the C

38、D changer unit rear, take out the unit. Fig.7 Fig.8 F E F Antenna terminal G CD tray panel CD tray panel ? Removing the front panel assembly (See Fig.10 to 11) ? Prior to performing the following procedures, remove the top cover. ? Also remove the CD changer unit. 1. Disconnect the parallel wire and

39、 the cord wire from the connectors CN201, CN401 on the main PCB. 2. Remove one screws H retaining the front panel assembly onto the bottom of the body. 3. Remove two screws I on the left and right side of the set retaining the panel front from the bottom and then remove then GND lug b that comes fro

40、m the power amp and supply PCB. 4. Disengage the claws c on both sides of the front panel assembly and then remove the assembly. Fig.10 H Fig.11 Claw c GND lug b Fig.13 CD PCB Short round CN601 Fig.12 ? Removing the MAIN PCB (See Fig.12 to 13) ? Prior to performing the following procedures, remove t

41、he top cover. ? Also remove the CD changer unit. 1. Disconnect the wires from CN701, CN702 and CN703 on the CD PACK PCB, which is located on the down side of the CD changer unit. 2. The four screws J that retain the CD PCB should be removed. 3. Remove the CD PCB by pulling it toward the side where t

42、he CN701 is located. 4. Using solder, short the CD pickup to connect to short round. Caution After re-connecting the wires, be sure to remove the shorting solder from the GND connection. 5. Disconnect the card wire from the connector CN701 on the main PCB and then remove the main PCB. J CD PCB J J F

43、ig.14 Fig.15 assembly e ( Green color ) e ( Red color ) e ( Green color )e ( Red color ) d CD changer unit ? Removing the CD changer mechanism assembly (See Fig.14 to 15) ? Prior to performing the following procedures, remove the top cover. ? Also remove the CD changer unit. 1. Turn the CD changer m

44、echanism cover base and remove the screws d connecting the unit to the CD changer mechanism assembly. 2. Removing four screws e retaining the CD mechanism holder assembly. Caution When replacing the CD changer mechanism assembly, be sure not to mistake the positions of the silver color and copper co

45、lor spring. CD changer mechanism Fig.16 Fig.17 Fig.18 Motor locker Turn table motor Obligue gear , and then remove the CD tray g M L f CD pickup Shaft ? Removing the CD pickup (See Fig.16) ? Prior to performing the following procedures, remove the top cover. ? Also remove the CD changer unit. ? Also

46、 remove the CD changer mechanism. 1. Widen the section f. 2. While keeping the section f wide open, push the section g in the direction of the arrow to remove the shaft, and then remove the CD pickup. ? Replacing the loading motor and rotor belt of the CD changer (See Fig .17) ? Prior to performing

47、the following procedures, remove the top cover. ? Also open the CD changer tray. 1. Remove the two screws L retaining the CD changer tray loading motor. 2. Remove the two screws M retaining the gear plate and take it out, after remove the rotor belt from the pulley. ? Replacing the CD turn table and

48、 remov- ing the motor (See Fig. 18 ) ? Prior to performing the following procedures, remove the top cover. ? Also remove the CD changer unit. 1. Remove the one screws N retaining the CD (Turn table). 2. Remove the two screws O retaining the stopper brackets on both sides of the CD changer unit. 3. Remove the stopper brackets from both sides of the CD changer unit. 4. Pull out the CD tray from the CD changer unit, all the way and lift the tray (u/ ward) to remove. 5. Remove the gear and after push out the tray motor locker and pull out the tray motor from the CD tray.