Yamaha-CDS2000-sacd-sm维修电路原理图.pdf

《Yamaha-CDS2000-sacd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS2000-sacd-sm维修电路原理图.pdf（59页珍藏版）》请在收音机爱好者资料库上搜索。

1、I CONTENTS TO SERVICE PERSONNEL . 23 PREVENTION OF ELECTROSTATIC DISCHARGE . 4 FRONT PANEL . 5 REAR PANELS . 57 REMOTE CONTROL PANEL . 8 SPECIFICATIONS / 参考仕様. 89 INTERNAL VIEW . 9 DISASSEMBLY PROCEDURES / 分解手順. 1016 TEST MODE / . 17 UPDATING FIRMWARE / 書込 . 1824 DISPLAY DATA . 25 IC DATA . 2628 PIN

2、 CONNECTION DIAGRAMS. 2930 BLOCK DIAGRAM. 31 PRINTED CIRCUIT BOARDS. 3240 SCHEMATIC DIAGRAMS. 4145 REPLACEMENT PARTS LIST . 4758 REMOTE CONTROL. 59 101078 SERVICE MANUAL SUPER AUDIO CD PLAYER 2007 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either

3、 in print or electronically without permission. P.O.Box 1, Hamamatsu, Japan 07.12 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Y

4、AMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perfo

5、rm as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorizatio

6、n, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are conti

7、nually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expe

8、nsive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the u

9、nit. CD-S2000 CD-S2000 RadioFans.CN 收音机爱 好者资料库 2 CD-S2000 CD-S2000 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproduct

10、ive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder

11、or components located inside the enclosure of this product, wash your hands before handling food. 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Me

12、asurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohms shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe sure to test

13、 for leakage with the AC plug in both polarities. 本機搭載基板付接合 部無鉛付。 無鉛種類、修理時下記 無鉛使用推奨。 Sn+Ag+Cu （錫+銀+銅） Sn+Cu （錫+銅） Sn+Zn+Bi （錫+亜鉛+） 注意： 無鉛融点温度通常鉛入比3040 程度高、合 使用。 All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder c

14、urrently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than

15、that of the lead solder, be sure to use a soldering iron suitable to each solder. About lead free solder / 無鉛 I TO SERVICE PERSONNEL WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To pro

16、tect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from the laser pick-up unit at all times. Do not stare at the laser beam

17、at any time. 2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Emitting conditions:

18、1) When the top cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing

19、 during this period! If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions. 2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipping from t

20、he factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device. RadioFans.CN 收音机爱 好者资料库 3 CD-S2000 CD-S2000 Material: SA-CDSemiconductor laser (AlGaInP) CDSemiconductor laser

21、 (AlGaAs) Wavelength: SA-CD650 nm CD780 nm Warning for power supply The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This primary area is not shielded so it is possible to touch copper tracks and/or compo

22、nents when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area. Note: The screws on the DVD mechanism may never be touched, removed or re-adjusted. Handle the DVD mechanism with care when the unit has to be exchanged! The DVD mech

23、anism is very sensitive for dropping or giving shocks. Laser Diode Properties Laser Output: SA-CD5 mW (max.) CD7 mW (max.) B, G models 4 CD-S2000 CD-S2000 I PREVENTION OF ELECTROSTATIC DISCHARGE Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components com

24、monly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transis- tors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of compo- nent damage caused by electro stat

25、ic discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potenti

26、al shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip solder

27、ing iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electri

28、cal charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa- rable

29、 conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the protective mate- rial to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and obs

30、erve all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brush- ing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES

31、device). Grounding for electrostatic breakdown prevention 1. Human body grounding. Use the antistatic wrist strap to discharge the static electricity from your body. 2. Work table grounding. Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground th

32、e sheet. Caution: The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup. 1M-ohms Conductive material (sheet) or steel sheet Anti-static wrist strap 5 CD-S2000 CD-S2000 I FRONT PANEL CD-S2000 (U, C, R, T, K,

33、A, B, G, L, J models) I REAR PANELS CD-S2000 (U, C models) CD-S2000 (R model) 6 CD-S2000 CD-S2000 CD-S2000 (T model) CD-S2000 (K model) CD-S2000 (A model) 7 CD-S2000 CD-S2000 CD-S2000 (B, G models) CD-S2000 (L model) CD-S2000 (J model) 8 CD-S2000 CD-S2000 I Audio Section / 部 Frequency Response / 周波数

34、特性 SA-CD . 2 Hz to 50 kHz (-3 dB) CD .2 Hz to 20 kHz Total Harmonic Distortion + Noise (1 kHz) / 高調波歪率 （1 kHz） SA-CD . 0.0017 % or less CD .0.002 % or less Signal to Noise Ratio / 信号対雑音比 (IHF-A Network) .116 dB or more Dynamic Range / SA-CD .110 dB or more CD .100 dB or more Output Voltage (1 kHz, 0

35、 dB) / 出力電圧 （1 kHz、0 dB） . 2.0 0.3 V I General / 総合 Power Supply / 電源電圧 U, C models .AC 120 V, 60 Hz R, L models .AC 110/120/220/230-240 V, 50/60 Hz T model.AC 220 V, 50 Hz K model.AC 220 V, 60 Hz A model.AC 240 V, 50 Hz B, G models .AC 230 V, 50 Hz J model . AC 100 V, 50/60 Hz Power Consumption / 消

36、費電力 U, C, R, T, K, A, B, G, L models . 30 W J model . 25 W Off-state Power Consumption / OFF時消費電力 . 0 W Dimensions (W x H x D) / 寸法 （幅高奥行） . 435 x 137 x 440 mm (17-1/8” x 5-3/8” x 17-5/16”) Weight / 質量 . 15 kg (33 lbs. 1 oz.) Finish / 仕上 Black color . U, C, R, T, K, A, B, G, L, J models Silver color

37、 . U, C, R, T, K, A, B, G, L, J models Accessories / 付属品 Remote control x 1, Battery (R6, AA, UM-3) x 2, Audio pin cable (1.5 m) x 1, Power cable (2 m) x 1 *Specifications are subject to change without notice due to product improvements. 参考仕様外観予告変更。 I SPECIFICATIONS / 参考仕様 U . U.S.A. model C . Canad

38、ian model R . General model T . Chinese model K . Korean model A . Australian model B . British model G . European model L . Singapore model J. Japanese model I REMOTE CONTROL PANEL CDX5 9 CD-S2000 CD-S2000 435 (17-1/8) 137 (5-3/8)440 (17-5/16) 418 (16-7/16)120 (4-3/4)8 (5/16) 14 (9/16) 17 (11/16) D

39、IMENSIONS / 寸法図 Unit: mm (inch) 単位：mm （） I INTERNAL VIEW 1 POWER TRANSFORMER for DIGITAL/ LOADER 2 POWER TRANSFORMER for AUDIO 3 POWER (2) P.C.B. (R, L models) 4 POWER (1) P.C.B. 5 LOADER ASSY 6 AUDIO P.C.B. 7 DIGITAL (1) P.C.B. 8 DIGITAL (5) P.C.B. 9 POWER (3) P.C.B. 0 DIGITAL (4) P.C.B. A DIGITAL

40、(3) P.C.B. B DIGITAL (2) P.C.B. 234567 8 B 9 0A 1 10 CD-S2000 CD-S2000 I DISASSEMBLY PROCEDURES / 分解手順 Fig. 1 (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Panel Side L/R a. Remove 2 screws (1), coned disc spring L and washer side. (Fig. 1) b.

41、Lift the panel side L a little, release hooks at 3 locations and then remove the panel side L. (Fig. 1) c. Remove 2 screws (2) and then remove 2 washers. (Fig. 1) d. Lift the panel side R a little, release hooks at 3 loca- tions and remove the panel side R. (Fig. 1) 2. Removal of Top Cover a. Remove

42、 7 screws (3), 2 screws (4) and 2 screws (5). (Fig. 1) b. Remove the top cover. (Fig. 1) （番号順部品取外。） AC電源、電源抜。 1. L/R外方 a. 12本、L、外 。 （Fig. 1） b. L少持上、3所外 、L取外。 （Fig. 1） c. 22本外、2個外 。 （Fig. 1） d. R少持上、3所外 、R取外。 （Fig. 1） 2. 外方 a. 37本、42本、52本外。 （Fig. 1） b. 取外。 （Fig. 1） Panel side L L Panel side R R Washer side Washer side Coned disc spring L L Coned disc spring L L Front panel Top cover 7 6 7 3 1 3 4 5 2 Hook Hook POWER ON / OFF switch “PO