Sony Strda5000Es 电路图.pdf

《Sony Strda5000Es 电路图.pdf》由会员分享，可在线阅读，更多相关《Sony Strda5000Es 电路图.pdf（170页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. *“DTS”, “DTS-ES Extended Surround”, and “Neo:

2、6” are trademarks of Digital Theater Systems, Inc. AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 170 watts per channel minimum RMS power, with no more than 0.6% total harmonic dist

3、ortion from 250 milliwatts to rated output. Amplifier section Models of area code US, Canadian, Taiwan: POWER OUTPUT Rated Power Output at Stereo Mode1) (8 ohms 20 Hz 20 kHz, THD 0.6%) 170 W + 170 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.6%) 150 W + 150 W Reference Power O

4、utput (8 ohms 20 Hz 20 kHz, THD 0.6%) FRONT2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W (4 ohms 20 Hz 20 kHz, THD 0.6%) FRONT2): 150 W + 150 W CENTER2): 150 W SURR2): 150 W + 150 W SURR BACK2): 150 W + 150 W Models of area code AEP and Chinese: POWER OUTPUT Rate

5、d Power Output at Stereo Mode1) (8 ohms 1 kHz, THD 0.7%) 170 W + 170 W Reference Power Output at Stereo Mode (4 ohms 1 kHz, THD 0.7%) 150 W + 150 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W (4 ohms 1 kHz, T

6、HD 0.7%) FRONT2): 150 W + 150 W CENTER2): 150 W SURR2): 150 W + 150 W SURR BACK2): 150 W + 150 W 1) Depending on the sound field settings and the source, there may be no sound output. 2) Measured under the following conditions: 3) Models of area code US, Canadian only. 4) Models of area code Taiwan

7、only. Frequency response Area codePower requirements US and Canadian120 V AC, 60 Hz Taiwan110 V AC, 60 Hz AEP230 V AC, 50/60 Hz Chinese220-230 V AC, 50/60 Hz PHONORIAA equalization curve 0.5 dB MULTI CHANNEL INPUT 1, 2, CD/ SACD, TAPE, MD/ DAT, DVD, TV/SAT, VIDEO 1, 2, 3 10 Hz 40 kHz 3 dB (when soun

8、d field and equalizer bypassed) FM STEREO FM/AM RECEIVER SPECIFICATIONS STR-DA5000ES Ver. 1.2 2005.07 9-961-110-03Sony Corporation 2005G05-1Audio Group 2005.07Published by Sony Engineering Corporation US Model Canadian Model AEP Model E Model Chinese Model Continued on next page RadioFans.CN 收音机爱 好者

9、资料库 2 STR-DA5000ES Inputs (Analog) Inputs (Digital) Outputs EQUALIZER FM tuner section Tuning range87.5 - 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75 ohms Useable sensitivity1 76 dB 70 dB 1.2 dBf, 1 V/75 oh

10、ms S/N Mono: Stereo: Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range Models of area code U, CA: 530 1,710 kHz7) (With 10-kHz tuning scale) 531 1,710 kHz7) (With 9-kHz tunin

11、g scale) Models of other area codes: 531 1,602 kHz (With 9-kHz tuning scale) AntennaLoop antenna Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5% (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 5) You can change the AM tuning scale to 9 k

12、Hz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video:1 Vp-

13、p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75 ohms COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms General Power requirements PHONOS/N: 86 dB MULTI CHANNEL INPUT 1, 2, CD/ SACD, TAPE, MD/ DAT, DVD, TV/SAT, VIDEO 1, 2, 3 S/N: 96 dB CD/SACD, DVD (

14、Coaxial) S/N: 96 dB (A, 20 kHz LPF) CD/SACD, DVD, TV/ SAT, MD/DAT, VIDEO3 (Optical) S/N: 96 dB (A, 20 kHz LPF) TAPE, MD/DAT (REC OUT), VIDEO 1, 2 (AUDIO OUT) FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK (L/R), SUB WOOFER Gain levels10 dB, 1 dB step Area codePower requirements US and Canadian120 V

15、AC, 60 Hz AEP230 V AC, 50/60 Hz Taiwan110 V AC, 60 Hz Chinese220-230 V AC, 50/60 Hz Power consumption Power consumption (during standby mode) 1 W AC outlets Dimensions430 175 470 mm including projecting parts and controls Mass (Approx.)13 kg Supplied accessories FM wire antenna (1) AM loop antenna (

16、1) AC power cord (1) Remote commander RM-LJ312 (1) R6 (size-AA) batteries (3) Remote commander RM-US106 (1) (US and Canadian models) R6 (size-AA) batteries (2) (US and Canadian models) Design and specifications are subject to change without notice. Area codePower consumption Except Canadian300 W Can

17、adian500 VA Area codeAC outlets US and Canadian2 switched, 120 W/1A MAX AEP1 switched, 100 W MAX Taiwan2 switched, 100 W MAX Chinese (no AC outlet) RadioFans.CN 收音机爱 好者资料库 3 STR-DA5000ES Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a ta

18、ntalum capacitor may be dam- aged by heat. Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to t

19、he customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part hav

20、ing a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammete

21、r. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are

22、 examples of a pas- sive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITI

23、QUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN

24、THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder con

25、tains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons

26、can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosi

27、ty Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges oc- cur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. RadioFans.CN 收音

28、机爱 好者资料库 4 STR-DA5000ES 1.SERVICING NOTES.5 2.GENERAL Location of Controls . 10 3.DISASSEMBLY 3-1.Disassembly Flow . 11 3-2.Case . 11 3-3.Front Panel Section . 12 3-4.D-AMP Board . 13 4.TEST MODE. 14 5.ELECTRICAL ADJUSTMENTS. 15 6.DIAGRAMS 6-1.Block Diagram AUDIO IN Section . 19 6-2.Block Diagram EL

29、ECTRICAL VOLUME Section . 20 6-3.Block Diagram DIGITAL 1 Section . 21 6-4.Block Diagram DIGITAL 2 Section . 22 6-5.Block Diagram DIGITAL 3 Section . 23 6-6.Block Diagram PRE OUT Section . 24 6-7.Block Diagram POWER AMP Section . 25 6-8.Block Diagram VIDEO IN Section . 26 6-9.Block Diagram CIS/DISPLA

30、Y Section . 27 6-10. Block Diagram POWER SUPPLY Section . 28 6-11. Note for Printed Wiring Boards and Schematic Diagrams . 29 6-12. Printed Wiring Board AUDIO Board (Component Side) . 30 6-13. Printed Wiring Board AUDIO Board (Conductor Side) . 31 6-14. Schematic Diagram AUDIO Board (1/4) . 32 6-15.

31、 Schematic Diagram AUDIO Board (2/4) . 33 6-16. Schematic Diagram AUDIO Board (3/4) . 34 6-17. Schematic Diagram AUDIO Board (4/4) . 35 6-18. Printed Wiring Board ANALOG SUB Board . 36 6-19. Schematic Diagram ANALOG SUB Board . 37 6-20. Schematic Diagram DIGITAL Board (1/9) . 39 6-21. Schematic Diag

32、ram DIGITAL Board (2/9) . 40 6-22. Schematic Diagram DIGITAL Board (3/9) . 41 6-23. Schematic Diagram DIGITAL Board (4/9) . 42 6-24. Schematic Diagram DIGITAL Board (5/9) . 43 6-25. Schematic Diagram DIGITAL Board (6/9) . 44 6-26. Schematic Diagram DIGITAL Board (7/9) . 45 6-27. Schematic Diagram DI

33、GITAL Board (8/9) . 46 6-28. Schematic Diagram DIGITAL Board (9/9) . 47 6-29. Printed Wiring Board DIGITAL Board (Component Side) . 48 6-30. Printed Wiring Board DIGITAL Board (Conductor Side) . 49 6-31. Printed Wiring Board D-AMP Section (Component Side) . 50 6-32. Printed Wiring Boards D-AMP Secti

34、on (Conductor Side) . 51 6-33. Schematic Diagram D-AMP Section (1/6) . 52 6-34. Schematic Diagram D-AMP Section (2/6) . 53 6-35. Schematic Diagram D-AMP Section (3/6) . 54 6-36. Schematic Diagram D-AMP Section (4/6) . 55 6-37. Schematic Diagram D-AMP Section (5/6) . 56 6-38. Schematic Diagram D-AMP

35、Section (6/6) . 57 6-39. Printed Wiring Board PRE-OUT Board (Component Side) (US, CND models). 58 6-40. Printed Wiring Board PRE-OUT Board (Conductor Side) (US, CND models). 59 6-41. Schematic Diagram PRE-OUT Board (US, CND models). 60 6-42. Schematic Diagram VIDEO Board (1/3) . 61 6-43. Schematic D

36、iagram VIDEO Board (2/3) . 62 6-44. Schematic Diagram VIDEO Board (3/3) . 63 6-45. Printed Wiring Board VIDEO Board (Component Side) . 64 6-46. Printed Wiring Board VIDEO Board (Conductor Side) . 65 6-47. Printed Wiring Board S-VIDEO Board . 66 6-48. Schematic Diagram S-VIDEO Board . 67 6-49. Printe

37、d Wiring Board CIS Board (US, CND models) . 68 6-50. Schematic Diagram CIS Board (US, CND models). 69 6-51. Printed Wiring Board FL Board . 70 6-52. Schematic Diagram FL Board . 71 6-53. Printed Wiring Boards PANEL Section . 72 6-54. Schematic Diagram PANEL Section . 73 6-55. Printed Wiring Board RE

38、G Section (Component Side) . 74 6-56. Printed Wiring Boards REG Section (Conductor Side) . 75 6-57. Schematic Diagram REG Section (1/2) . 76 6-58. Schematic Diagram REG Section (2/2) . 77 6-59. IC Pin Function Description . 90 7.EXPLODED VIEWS 7-1.Case Section .109 7-2.Front Panel Section-1.110 7-3.

39、Front Panel Section-2.111 7-4.Chassis Section-1 .112 7-5.Chassis Section-2 .113 7-6.Chassis Section-3 .114 7-7.Chassis Section-4 .115 7-8.Chassis Section-5 .116 7-9.REG Board Section.117 7-10. D-AMP Board Section .118 8.ELECTRICAL PARTS LIST.119 TABLE OF CONTENTS 5 STR-DA5000ES SECTION 1 SERVICING N

40、OTES MODEL IDENTIFICATION Back Panel PART No. ModelPART No. US model4-246-511-0 Canadian model4-246-511-1 AEP model4-246-511-2 Chinese model4-246-511-4 Taiwan model4-246-511-6 Ver 1.1 ERROR MESSAGES If there is a malfunction, the display shows a code of two numbers and a message. You can check the c

41、ondition of the system by message. Refer to the following table to solve the problem. messagescheck codecause and response DECODE ERROR01Appears when the signal which the receiver can not decode (example DSD-CD) is input when “DEC. PRI.” in the CUSTOM IZE menu is set to “PCM”. Set to “AUTO”. PROTECTOR11Irregular current output to the speakers. Turn off the receiver and check the speaker connection. Then turn on the power again. Be comes this display, When short current flowed with breakage o