IC-2710H_user.pdf

《IC-2710H_user.pdf》由会员分享，可在线阅读，更多相关《IC-2710H_user.pdf（88页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iC-2710h DUAL BAND FM TRANSCEIVER IC-2710H.qxd 02.2.8 16:55 Page A (1,1) RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fi re hazard or result in an electric shock. RWARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires you

2、r full attention anything less may result in an accident. NEVERconnect the transceiver to a power source of more than 16 V DC. This connection will ruin the transceiver. NEVERconnect the transceiver to a power source using reverse polarity. This connection will ruin the transceiver. NEVERcut the DC

3、power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVERplace the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVERlet objects impede the operation of the co

4、oling fan on the rear panel. DO NOT push the PTT when not actually desiring to transmit. i IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUALThis instruction man- ual contains important operating instructions for the IC-2710H. EXPLICIT

5、 DEFINITIONS The explicit defi nitions below apply to this instruction manual. CAUTIONS WORDDEFINITION RWARNING Personal injury, fi re hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fi re or electric shock.

6、 The IC-2710H Europe versions comply with essential re- quirements of the 89/336/EEC directive for Electromagnetic Compatibility. This compliance is based on conformity with the ETSI specifi cation prEIS300 684 (EMC product standard for Commercially Available Amateur Radio Equipment). IC-2710H.qxd 0

7、2.2.8 16:55 Page i (1,1) ii UNPACKING Accessories included with the transceiver: Qty. DC power cable (OPC-346). 1 Mobile mounting bracket . 1 Microphone (HM-98). 1 Fuse (20 A). 1 Knob bolt (M4 x 8) . 4 Mounting bolt (M5 x 12). 4 Nut (M5). 4 Spring washer (M5). 4 Flat washer (M5). 4 Self-tapping scre

8、ws (A0 5 x 16). 4 DO NOT allow children to play with any radio equipment containing a transmitter. During mobile operation, DO NOT operate the transceiver without running the vehicles engine. When transceiver power is ON and your vehicles engine is OFF, the vehicles battery will soon become exhauste

9、d. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods. AVOID using or placing the transceiver in areas with tem- peratures below 10C (+14F) or above +60C (+140F) or in areas subject to direct sunlight, such as the dashboard. AVOID the use of chemical agents s

10、uch as benzine or al- cohol when cleaning, as they can damage the transceiver surfaces. USEIcom microphones only (supplied or optional). Other manufacturers microphones have different pin assignments and may damage the transceiver. IC-2710H.qxd 02.2.8 16:55 Page ii (1,1) TABLE OF CONTENTS iii IMPORT

11、ANT . i EXPLICIT DEFINITIONS . i CAUTIONS . i UNPACKING . ii TABLE OF CONTENTS . iii 1PANEL DESCRIPTION . 1 8 I Front panel . 1 I Function display . 3 I Rear panel . 5 I Microphone . 6 I Microphone keypad . 7 2INSTALLATION . 9 14 I Installation methods . 9 I Location . 10 I Single body installation

12、. 10 I Microphone connection . 11 I Separate installation . 11 I Optional MB-58 installation . 12 I Battery connection . 13 I DC power supply connection . 13 I Antenna installation . 14 3SETTING A FREQUENCY . 15 19 I Preparation . 15 I Lock functions . 16 I Using a tuning dial . 17 I Using Y/Z switc

13、hes . 17 I Tuning step selection . 18 I Using the keypad . 19 4BASIC OPERATION . 20 26 I Receiving . 20 I Monitor function . 21 I Audio mute function . 21 I Avionics band receive . 21 I Sub band access . 22 I Sub band mute/sub band busy beep . 23 I Para-watch . 24 I Transmitting . 25 I Selecting the

14、 output power . 25 I Crossband full duplex . 26 I One-touch PTT function . 26 5REPEATER OPERATION . 27 31 I Operation . 27 I Subaudible tones . 29 I Offset frequency . 30 I Auto repeater . 31 6MEMORY OPERATION . 32 36 I General description . 32 I Memory channel selection . 32 I Programming a memory

15、channel . 33 I Programming a memory channel via the microphone . 34 I Transferring memory contents . 35 I Memory clearing . 36 7CALL CHANNEL OPERATION . 37 38 I Calling up a call channel contents . 37 I Transferring call channel contents . 37 I Programming a call channel . 38 8SCRATCH PAD MEMORY . 3

16、9 40 I What is a scratch pad memory? . 39 IC-2710H.qxd 02.2.8 16:55 Page iii (1,1) iv I Calling up a scratch pad memory . 39 I Transferring scratch pad memory contents . 40 9SCAN OPERATION . 41 46 I Scan types . 41 I Start/stop scan . 42 I Programming scan edges . 43 I Programming scan edges via the

17、 microphone . 44 I Skip channel setting . 45 I Scan resume condition . 46 10 PRIORITY WATCH . 47 48 I Priority watch types . 47 I Priority watch operation . 48 11 DTMF MEMORY ENCODER . 49 52 I Programming a DTMF code . 49 I Clearing the DTMF memory contents . 49 I Programming a DTMF code via the mic

18、rophone . 50 I Transmitting a DTMF code . 51 I DTMF speed . 52 12 POCKET BEEP AND TONE SQUELCH . 53 55 I Pocket beep operation . 53 I Tone squelch operation . 54 I Tone scan . 55 13 PAGER AND CODE SQUELCH . 56 62 I Pager function . 56 I Code channels . 57 I Code programming . 58 I Pager operation .

19、59 I Code squelch function . 61 I Code squelch operation . 62 14 EXTERNAL DTMF REMOTE . 63 64 15 OPTIONAL UNIT INSTALLATION . 65 I Optional unit installation . 65 16 WIRELESS OPERATION . 66 71 I Connection . 66 I HM-90 WIRELESS MICROPHONE. 66 I EX-1759 installation . 67 I HM-90 switches . 68 I Micro

20、phone address . 71 17 OTHER FUNCTIONS . 72 74 I Beep tones on/off . 72 I Time-out timer . 72 I Auto power-off . 73 I Cooling fan setting . 73 I Microphone F-1/F-2 keys . 74 I Display dimmer setting . 74 I Demonstration display . 74 18 MAINTENANCE . 75 77 I Troubleshooting . 75 I Fuse replacement . 7

21、7 I Partial resetting . 77 I Total resetting . 77 19 SPECIFICATIONS . 78 20 OPTIONS . 79 80 21 MODE ARRANGEMENT CHART . 81 82 IC-2710H.qxd 02.2.8 16:55 Page iv (1,1) PANEL DESCRIPTION1 1 q POWER SWITCH POWER Turns power ON and OFF when pushed for 1 sec. w TUNING DIALS Select the operating frequency

22、(p. 17), the memory channel (p. 32), the contents of the set mode display (p. 82) and the scanning direction. (p. 42) Select the main band when pushed. (p. 15) When the sub band is selected, activate the sub band function when pushed and held. (p. 22) When the main band is selected, change the operating band (for para watch) when pushed and held. (p. 24) e SQUELCH CONTROLS SQL(MONI) Vary the squelch level. (p. 20) RF attenuator activates and increases the attenuation when rotated clockwise to the center posi