Aiwa-ZV616-cs-sm 电路图 维修手册.pdf

《Aiwa-ZV616-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-ZV616-cs-sm 电路图 维修手册.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Personal Audio Company Published by Sony Engineering Corporation XP-ZV610/ZV616 US Model Canadian Model XP-ZV610 AEP Model UK Model XP-ZV616 E Model XP-ZV610/ZV616 Australian Model XP-ZV610 PORTABLE CD PLAYER 9-961-546-02 2004D16-1 2004.04 Ver 1.1 2004.04 SPECIFICATIO

2、NS Photo : XP-ZV616 System Compact disc digital audio system Laser diode properties Material: GaAlAs Wavelength: = 770 - 800 nm Emission duration: Continuous Laser output: Less than 44.6 W (This output is the value measured at a distance of 200 mm from the objective lens surface on the optical pick-

3、up block with 7 mm aperture.) D-A conversion 1-bit quartz time-axis control Frequency response 20 - 20 000 Hz +1 2dB (measured by JEITA) Output (at 4.5 V input level) Headphones (stereo minijack) Approx. 5 mW + Approx. 5 mW at 16 (Approx. 1.5 mW + Approx. 1.5 mW at 16 )* * For the customers in Europ

4、e Power requirements Two LR6 (size AA) batteries: 1.5 V DC 2 AC power adaptor (DC IN 4.5 V jack) Rated current: 500 mA Battery life*1 (approx. hours) When you use the CD player on a flat and stable surface. When SOUND mode is set to “OFF.” Playing time varies depending on how the CD player is used.

5、When using two Sony alkaline batteries LR6 (SG) (produced in Japan) EASS GP “EASS GP 1” “EASS GP 2” Audio CD5045 ATRAC CD*28585 MP3 CD*36565 *1 Measured value by the standard of JEITA (Japan Electronics and Information Technology Industries Association) *2 Recorded at 48 kbps *3 Recorded at 128 kbps

6、 Operating temperature 5C - 35C (41F - 95F) Dimensions (w/h/d) (excluding projecting parts and controls) Approx. 135.8 27.2 135.8 mm (538 1 18 5 38 in.) Mass (excluding accessories) Approx. 180 g (6.4 oz.) US and foreign patents licensed from Dolby Laboratories. Design and specifications are subject

7、 to change without notice. Supplied accessories AC power adaptor (AC-ES455K)(1) Earphones (1) Remote control (1)(XP-ZV616) CD-ROM* (SonicStage)(1) Users guide for SonicStage (1) Operating lnstructions * Do not play a CD-ROM on an audio CD player. Model Name Using Similar MechanismXP-ZV71 CD Mechanis

8、m TypeCDM-3325ER Optical Pick-up NameDAX-25E RadioFans.CN 收音机爱 好者资料库 2 XP-ZV610/ZV616 CAUTION INVISIBLE LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS SAFETY-RELATED

9、 COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Flexible Circ

10、uit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement

11、Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Unleaded solder Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may

12、not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the sol

13、der joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to

14、flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. CAUTION Use of controls or adjustments or performance of procedures other th

15、an those specified herein may result in hazardous radiation exposure. On AC power adaptor Use only the AC power adaptor supplied. If your CD player is not supplied with the one, use the AC-E45HG AC power adaptor. Do not use any other AC power adaptor. It may cause a malfunction. Polarity of the plug

16、 Do not touch the AC power adaptor with wet hands. Connect the AC power adaptor to an easily accessible AC outlet. Should you notice an abnormality in the AC power adaptor, disconnect it from the AC outlet immediately. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE M

17、ARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY. Music sources playable on this CD player You can play the

18、following 3 music sources on this CD player: Audio CDs (CDDA format) CDs with ATRAC3plus/ATRAC3 format files (ATRAC CD) CDs with MP3 format files (MP3 CD) Usable disc formats You can use ISO 9660 Level 1/2 and Joliet extension format discs only. About CD-Rs/RWs This CD player can play CD-Rs/RWs reco

19、rded in the ATRAC3plus/ATRAC3, MP3 or CDDA* format, but playback capability may vary depending on the quality of the disc and the condition of the recording device. * CDDA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for the Audio CDs. Music discs encoded with

20、copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that

21、 do not conform to the CD standard and may not be playable by this product. Notes This CD player cannot record music content on recordable media, such as CD-Rs/RWs. CD-Rs/RWs recorded in the ATRAC3plus/ATRAC3 format cannot be played on your computer. RadioFans.CN 收音机爱 好者资料库 3 XP-ZV610/ZV616 TABLE OF

22、 CONTENTS 1. SERVICING NOTE.4 2. GENERAL.6 3. DISASSEMBLY 3-1.Cabinet (Front) Assy .9 3-2.CD Mechanism Deck (CDM-3325ER), MAIN Board.10 3-3.Upper Lid . 11 3-4.CONTROL Board .12 3-5.Motor Assy (Sled)(M902), Optical Pick-up (DAX-25E), Turn Table Motor Assy (Spindle)(M901). 13 4. ELECTRICAL CHECKING. 1

23、4 5. DIAGRAMS. 15 5-1.Block Diagram . 16 5-2.Printed Wiring Board MAIN Board (Side A) . 17 5-3.Printed Wiring Board MAIN Board (Side B) .18 5-4.Schematic Diagram MAIN Board (1/4) . 19 5-5.Schematic Diagram MAIN Board (2/4) . 20 5-6.Schematic Diagram MAIN Board (3/4) . 21 5-7.Schematic Diagram MAIN B

24、oard (4/4) . 22 5-8.Printed Wiring Board CONTROL Board .23 5-9.Schematic Diagram CONTROL Board . 24 5-10. IC Pin Function Description. 30 6. EXPLODED VIEWS 6-1.Overall Section . 32 6-2.Cabinet Lower Section . 33 6-3.Upper Lid Section .34 6-4.CD Mechanism Section (CDM-3325ER). 35 7. ELECTRICAL PARTS

25、LIST.36 RadioFans.CN 收音机爱 好者资料库 4 XP-ZV610/ZV616 SECTION 1 SERVICING NOTE The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention

26、 to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc r

27、eflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. BEFORE REPLACING THE OPTICAL PICK-UP BLOCK Please be sure to check thoroughly the parameters as par the “Optical Pick-U

28、p Block Checking Procedures” (Part No.: 9-960-027-11) issued separately before replacing the optical pick-up block. FOK output: IC601 yg pin When checking FOK, remove the lead wire to disc motor. RF signal P-to-P value: 0.45 to 0.65 Vp-p LASER DIODE AND FOCUS SEARCH OPERATION CHECK During normal ope

29、ration of the equipment, emission of the laser diode is prohibited unless the upper lid is closed while turning ON the S820. (push switch type) The following checking method for the laser diode is operable. Method: Emission of the laser diode is visually checked. 1. Open the upper lid. 2. With a dis

30、c not set, turn on the S820 with a screwdriver having a thin tip as shown in Fig.1. 3. Press the u/ENT button. 4. Observing the objective lens, check that the laser diode emits light. When the laser diode does not emit light, automatic power control circuit or optical pickup is faulty. In this opera

31、tion, the objective lens will move up and down 4 times along with inward motion for the focus search. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT Fig. 1 Method to push the S820 S820 lever (lid detection) lever (lid detection) MAIN board 5 XP-ZV610/ZV616 TEST MODE The software version di

32、splay and LCD test can be performed when the test mode is activated. Procedure: 1. Confirm the set is not powered on. (Remove two batteries and disconnect the AC power adaptor.) 2. Short the solder land SL824 (TEST) on the MAIN board. 3. Turn on the main power. (Insert two batteries.) 4. Microcomput

33、er version is displayed for about a second. 5. After that all segments of the liquid crystal display are turned on. 6. Turn off the main power. (Remove two batteries.) 7. Open the solder land SL824 (TEST) on the MAIN board. Note : The solder should be removed clean. IC801 MAIN BOARD (SIDE B) SL824 (

34、TEST) 6 XP-ZV610/ZV616 SECTION 2 GENERAL This section is extracted from instruction manual. Locating the controls CD player 1 DSPL (display)/MENU button (16, 17, 20 - 25, 28) Use to enter the menu. Also use to enter the selection as well as u/ENT. 2 (group) button (15, 20, 21, 23, 24, 28) 3 (group)

35、+ button (15, 20, 21) 4 x (stop) button (15, 21, 23, 24, 28) 5 i (headphones) jack (14) 6 Display (12, 16 - 18, 20 - 22, 28) 7 Operation button (15, 17 - 25, 28) u*/ENT: play/pause/ enter ./ : skip/search U/u: Use to select a file, play mode, etc. 8 DC IN 4.5 V (external power input) jack (14) 9 VOL

36、 (volume) +*/buttons (15) q; OPEN switch (14, 26) Slide the switch to open the CD player lid. qa HOLD switch (rear) (24) Slide the switch in the direction of the arrow to disable the buttons on the CD player. * The button has a tactile dot. 7 XP-ZV610/ZV616 Display 1 Character information display (1

37、6) While playing an audio CD, disc name, track name, etc. appear on the 2 lines of the display, if recorded on the CD. While playing an ATRAC CD/MP3 CD, group name, file name, etc. appear on the 2 lines of the display, if recorded on the CD. Menu items also appear in this display. 2 Atrac3plus/MP3 i

38、ndication 3 Disc indication Lights up while the CD player is playing. 4 Battery indication (26) Roughly shows the remaining power of the battery. If “” flashes, the batteries are depleted. 5 Play list indication (18) For MP3 CD only 6 Group indication (17, 18) For ATRAC CD/MP3 CD only 7 Play mode in

39、dication (17, 18, 20) Shows various playmodes such as shuffle play and program play. “” shows repeat play. 8 SOUND indication (22) Shows the SOUND setting which has been selected on the menu. 8 XP-ZV610/ZV616 1 VOL (volume) +*/ buttons (15) 2 u* (play/pause) button (15) 3 x (stop) button (15) 4 HOLD

40、 switch (24) 5 Clip 6 ./ (skip/search) buttons (15) 7 (group) + button (15, 20, 21) 8 (group) button (15, 20, 21) * The button has a tactile dot. + Remote control (for XP-ZV616 only) Note Use only the supplied remote control. You cannot operate this CD player with the remote control supplied with ot

41、her CD players. 9 XP-ZV610/ZV616 Note : Disassemble the unit in the order as shown below. Note : Follow the disassembly procedure in the numerical order given. 3-1.CABINET (FRONT) ASSY 3-2.CD MECHANISM DECK (CDM-3325ER), MAIN BOARD (page 10) SET 3-1.CABINET (FRONT) ASSY (page 9) 3-3.UPPER LID (page

42、11) 3-4.CONTROL BOARD (page 12) 3-5.MOTOR ASSY (SLED) (M902), OPTICAL PICK-UP (DAX-25E), TURN TABLE MOTOR ASSY (SPINDLE) (M901) (page 13) 4 three claws 5 cabinet (front) assy 3 two claws 1 open battery case lid 2 seven screws SECTION 3 DISASSEMBLY 10 XP-ZV610/ZV616 3-2.CD MECHANISM DECK (CDM-3325ER)

43、, MAIN BOARD 1 connector (2P) (CN401) 2 connector (4P) (CN402) S810 3 flexible board (15P) (CN601) 4 three insulators 5 CD mechanism deck (CDM-3325ER) 6 MAIN board 7 battery link terminal 9 cabinet (lower) 8 knob(hold) When installing it, align the switch position as shown. 11 XP-ZV610/ZV616 3-3.UPP

44、ER LID 2 twist coil spring(left) 4 twist coil spring(right) 5 two dowels 6 upper lid 1 open left spring is removed in the direction of an arrow cabinet upper cabinet upper 3 open right spring is removed in the direction of an arrow 12 XP-ZV610/ZV616 3-4.CONTROL BOARD 1 ten screws 2 lid cover 0 escut

45、cheon 4 flexible cable qa upper lid assy 5 liquid crystal display panel 8 play button 7 sheet,insulating 9 control button 3 CONTROL board 6 connector (CN2001) 13 XP-ZV610/ZV616 3-5.MOTOR ASSY (SLED)(M902), OPTICAL PICK-UP (DAX-25E), TURN TABLE MOTOR ASSY (SPINDLE)(M901) 1 three screws (B1.7x4) 2 gea

46、r cover 4 optical pick-up (DAX-25E) chassis 5 three screws (B1.7x4) 6 turn table motor assy (spindle) (M901) 3 motor assy (sled) (M902) 14 XP-ZV610/ZV616 SECTION 4 ELECTRICAL CHECKING The CD section adjustments are done automatically in this set. In case of operation check, confirm that RF level. Precautions for Check 1.Perform check in the order given. 2.Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated. 3.Power supply voltage requirement : DC4.5 V in DC IN jack. (J401)