《Jvc-FSXA-3-UF-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-FSXA-3-UF-Service-Manual 电路图 维修手册.pdf（65页珍藏版）》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL COPYRIGHT 2006 Victor Company of Japan, Limited No.MB546 2006/7 COMPACT COMPONENT SYSTEM MB54620067 FS-XA3UF,FS-XA1B,FS-XA1E, FS-XA1EN,FS-XA1EV Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . .
2、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 3DISASSEMBLY . . . . . . . . .
3、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24 5TROUBLESHOOT
4、ING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27 CA-FSXA3 SP-FSXA3SP-FSXA3 CA-FSXA1SP-FSXA1SP-FSXA1 RadioFans.CN 收音机爱 好者资料库 1-2 (No.MB546) SPECIFICATION Manufactured under license from Dolby Laboratories. Dolby
5、, Pro Logic, MLP lossless, and the double-D symbol are trademarks of Dolby Laboratories. DTS and DTS 2.0+ Digital Out are trademarks of Digital Theater Systems, Inc. Official DivX Certified product Plays all versions of DivX video (including DivX 6) with standard playback of DivX media files DivX, D
6、ivX certified, and associated logos are trademarks of DivX, Inc. and are used under licence. USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE BY A CONSUMER ENGAGING IN PERSONAL AND NON-COMMERCIAL ACTIVITIES. This product incorporates copyr
7、ight protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copy- right protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engin
8、eering or disassembly is prohibited. Designs and Specifications are subject to change without notice. GeneralPower sourceAC 230 V , 50 Hz AC 220 V , 50 Hz (for FS-XA3UF) Power consumption25 W (in operation)/ 4.0 W(on standby/display on) 1.0 W (on standby/display off) Weight2.6 kg External dimensions
9、 (W H D)150 mm 152.6 mm 252.9 mm DVD playerPlayable discsDVD VIDEO, DVD AUDIO, VCD, SVCD, CD CD-R/RW (VCD/SVCD/CD/MP3/WMA/JPEG/MPEG1/MPEG2 format) DVD-R/-RW (MP3/WMA/JPEG/DVD VIDEO/DVD VR CPRM/MPEG1/ MPEG2 format) DVD-ROM (MP3/WMA/JPEG/MPEG1/ MPEG2/DVD VR CPRM format) Video output Color systemPAL PA
10、L/NTSC selectable (for FS-XA3UF) Horizontal resolution500 lines Composite 11.0 V (p-p)/75 ,synchronization negative S-video 1Y output: 1.0 V (p-p)/75 ,synchronization negative at PAL 0.3 V (p-p)/75 at NTSC 0.286 V (p-p)/75 Component 1Y output: 1.0 V (p-p)/75 PB/PR output: 0.7 V (p-p)/75 Audio output
11、 Analog sound outputSpeakers 2 Output power20 W per channel min., RMS, at 4 at 1 kHz with no more than 10% total har- monic distortion Fitting impedance4 to 16 Headphones 111 mW/32 Fitting impedance16 to 1 k Subwoofer 1500 mVrms/10 k Digital sound output (FS-XA3UF) Optical 1-21 dBm to -15 dBm Audio
12、inputSound inputAUX 1400 mV/50 k 200 mV/50 k AUX 21.5 V/50 k 750 mV/50 k TunerFM tunerReceiving frequency 87.5 MHz to 108.0 MHz Antenna75 Unbalanced type AM (MW) tunerReceiving frequency 522 kHz to 1 629 kHz 531 kHz to 1 710 kHz (9 kHz step) (FS-XA3UF) 530 kHz to 1 710 kHz (10 kHz step) (FS-XA3UF) A
13、ntennaExternal antenna jack (loop antenna) SpeakerTypeFull range 1-way bass-reflex type Magnetically shielded type Speaker8cm wood cone 1 Frequency response55 Hz to 20 000 Hz Power handling capacity20 W Impedance4 Sound pressure level82 dB/W m Dimension (W H D)120 mm 150.5 mm 243 mm Weight1.7 kg eac
14、h RadioFans.CN 收音机爱 好者资料库 (No.MB546)1-3 SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized
15、in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be ma
16、de. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. Th
17、ese characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts
18、 List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown i
19、n the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric
20、shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on th
21、e exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly i
22、nto the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate che
23、ck method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC volt
24、age across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage
25、 measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
26、(3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some p
27、arts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as th
28、e resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each
29、 exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE RadioFans.CN 收音机爱 好者资料库 1-4 (No.MB546) 1.5 Safety Precautions (U.K only) (1) This design of this product contains special hardware and many circuits and components specially for safety purposes. F
30、or con- tinued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replace- ment parts must be identical to those used in the original circuits. (2) Any unauthorised design alterations or additions will void the manufacturers guarantee; furt
31、hermore the manufacturer cannot accept responsibility for personal injury or property damage resulting therefrom. (3) Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other than those listed in the manu
32、al. Please note however that many electrical and mechanical parts in the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety characteristics as the recomme
33、nded replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp
34、 edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 1.5.1Warning (1) Service should be performed by qualified personnel o
35、nly. (2) This equipment has been designed and manufactured to meet international safety standards. (3) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (4) Repairs must be made in accordance with the relevant safety standards. (5) It is essential t
36、hat safety critical components are replaced by approved parts. (6) If mains voltage selector is provided, check setting for local voltage. Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system
37、. (No.MB546)1-5 1.6Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.6.1 Grounding t
38、o prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conduct
39、ive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during
40、transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The teste
41、rs internal power source can easily destroy the laser diode. 1.7Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replaci
42、ng the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected
43、to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.8Attention when traverse unit is decomposed *Please refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the card wire is
44、disconnected from the connecto on the servo board. (If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the card wire. 1M Conductive material (conductive
45、sheet) or iron palate (caption) Anti-static wrist strap Short land section Card wire Traverse mechanism assembly pickup 1-6 (No.MB546) 1.9Important for laser products 1.CLASS 1 LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
46、 (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 4.CAUTION : This laser product uses visible and/or in
47、visible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.
48、CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS and PRINT ! Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation
49、check. WARNING LABEL and PRINT (No.MB546)1-7 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. 1-8 (No.MB546) SECTION 3 DISASSEMBLY 3.1Main body section 3.1.1Removing the side panel L and side panel R (See Figs.1 to 4) (1) From the back side of the main body, remove the four screws A attaching the side panels L/R. (See Fig.1.) (2) From the bottom side of the main body, remove the four screws B attaching the side panels L/R. (See Fig.2.) (3) From the both
免费区 
