Sony-STR-DA2ES-Service-Manual电路原理图.pdf

《Sony-STR-DA2ES-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STR-DA2ES-Service-Manual电路原理图.pdf（110页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL FM STEREO FM-AM RECEIVER SPECIFICATIONS STR-DA2ES/DB1080 Photo: STR-DA2ES Ver 1.1 2003.07 9-874-061-02Sony Corporation 2003G05-1Home Audio Company C 2003.07Published by Sony Engineering Corporation US Model Canadian Model STR-DA2ES AEP Model UK Model E Model STR-DB1080 Continued on ne

2、xt page This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. *“DTS”, “DTS-ES Extended Surround” and “Neo:6” are t

3、rademarks of Digital Theater Systems, Inc. AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code U only) With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 100 watts per channel minimum RMS power, with no more than 0.09 % total harmonic distortion

4、from 250 milliwatts to rated output. Amplifier section POWER OUTPUT Models of area code U, CA Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0 09 %) 100 W + 100 W (4 ohms 20 Hz 20 kHz, THD 0 09 %) 80 W + 80 W Reference Power Output (8 ohms 20 Hz 20 kHz, THD 0 09 %) FRONT1):100 W + 100 W

5、 CENTER1): 100 W SURR1): 100 W + 100 W SURR BACK1): 100 W (4 ohms 20 Hz 20 kHz, THD 0 09 %) FRONT:1) 80 W + 80 W CENTER1): 80 W SURR1): 80 W + 80 W SURR BACK1): 80 W Models of other area code Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0 7 %) 100 W + 100 W2) (4 ohms 1 kHz, THD 0 7 %) 90 W +

6、 90 W2) Reference Power Output2) (8 ohms 1 kHz, THD 0 7 %) FRONT1): 100 W + 100 W CENTER1): 100 W SURR1): 100 W + 100 W SURR BACK1): 100 W (4 ohms 1 kHz, THD 0 7 %) FRONT1): 90 W + 90 W CENTER1): 90 W SURR1): 90 W + 90 W SURR BACK1): 90 W (8 ohms 20 Hz 20 kHz, THD 0 09 %) FRONT1): 90 W + 90 W CENTER

7、1): 90 W SURR1): 90 W + 90 W SURR BACK1): 90 W (4 ohms 20 Hz 20 kHz, THD 0 09 %) FRONT1): 80 W + 80 W CENTER1): 80 W SURR1): 80 W + 80 W SURR BACK1): 80 W 1) Depending on the sound field settings and the source, there may be no sound output 2) Measured under the following conditions: Area codePower

8、requirements E240 V AC, 50 Hz SP, CEL, CEK, KR230 V AC, 50 Hz Frequency response PHONO CD/SACD, TAPE, MD/DAT, TV/SAT, DVD/LD, VIDEO 1, 2, 3 Inputs (Analog) PHONO MULTI CH IN 1, 2, CD/SACD, TAPE, MD/DAT, DVD/LD, TV/SAT, VIDEO 1, 2, 3 3) INPUT SHORT 4) Weighted network, input level RIAA equalization c

9、urve 0 5 dB 10 Hz 100 kHz +0 5/2 dB (when ANALOG DIRECT is selected) Sensitivity: 2 5 mV Impedance: 50 kilohms S/N3): 86 dB (A, 2 5 mV4) Sensitivity: 150 mV Impedance: 50 kilohms S/N3): 96 dB (A, 150 mV4) RadioFans.CN 收音机爱 好者资料库 2 STR-DA2ES/DB1080 Inputs (Digital) DVD/LD (Coaxial) DVD/LD, TV/SAT, MD

10、/DAT, VIDEO3 (Optical) Outputs TAPE, MD/DAT (REC OUT), VIDEO 1, 2 (AUDIO OUT) FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK, SUB WOOFER EQ BASS:99 Hz1 0 kHz MID (FRONT L/R, CENTER only): 198 Hz10 kHz TREBLE:1 0 kHz10 kHz Gain levels:10 dB, 0 5 dB step Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF)

11、S/N: 100 dB (A, 20 kHz LPF) Voltage: 150 mV Impedance: 2 2 kilohms Voltage: 2 V Impedance: 1 kilohms FM tuner section Tuning range87 5 - 108 0 MHz Antenna terminals75 ohms, unbalanced Sensitivity Mono:18 3 dBf, 2 2 V/75 ohms Stereo:38 3 dBf, 22 5 V/75 ohms Usable sensitivity11 2 dBf, 1 V/75 ohms S/N

12、 Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0 3% Stereo:0 5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0 5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range Models of area code U, CA With 10-kHz tuning scale: 530 1,710 kHz5) With 9-kHz tuning scale:531 1,7

13、10 kHz5) Models of area code E With 10-kHz tuning scale: 530 1,610 kHz5) With 9-kHz tuning scale:531 1,602 kHz5) Models of area code SP, CEL, CEK, KR With 9-kHz tuning scale:531 1,602 kHz AntennaLoop antenna Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortio

14、n0 5 % (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 5) You can change the AM tuning scale to 9 kHz or 10 kHz After tuning in any AM station, turn off the receiver Hold down TUNING + and press ?/1 All preset stations will be erased when you change the tuning scale To reset the scale t

15、o 10 kHz (or 9 kHz), repeat the procedure Video section Inputs/Outputs Video:1 Vp-p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0 286 Vp-p, 75 ohms COMPONENT VIDEO (Except for models of area code CEL, CEK): Y: 1 Vp-p, 75 ohms B-Y: 0 7 Vp-p, 75 ohms R-Y: 0 7 Vp-p, 75 ohms General Power requirements Area c

16、odePower requirements U, CA120 V AC, 60 Hz CEL, CEK230 V AC, 50/60 Hz SP220 230 V AC, 50/60 Hz E120/220/240 V AC, 50/60 Hz KR220 230 V AC, 60 Hz Power consumption Area codePower consumption U290 W CA340 VA CEL, CEK300 W SP, E, KR300 W Power consumption (during standby mode) 0 8 W (when “POWER SAVE”

17、in the CUSTOMIZE menu is set to “OFF”)/0 5 W (“ON”) AC outlets Area codeAC outlets U, CA2 switched, 120 W/1A MAX SP, CEL, CEK1 switched, 100 W MAX E2 switched, 100 W MAX Dimensions430 161 400 mm including projecting parts and controls Mass (Approx.)13 3 kg Supplied accessories FM wire antenna (1) AM

18、 loop antenna (1) Models of area code U, CA; Audio/video/control S cord (1) Control S cord (mini jack) (1) Remote commander RM-PG411 (1) R6 (size-AA) batteries (2) Models of other area codes; Remote commander RM-LP211 (1) R6 (size-AA) batteries (3) Design and specifications are subject to change wit

19、hout notice RadioFans.CN 收音机爱 好者资料库 3 STR-DA2ES/DB1080 Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Ex

20、posed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.

21、Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.

22、A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a

23、VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a pas- sive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable

24、. (See Fig. A) ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUE

25、L OU DANS LES SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS M

26、ANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. 4 STR-DA2ES/DB1080 1.SERVICING NOTES.5 2.GENERAL.6 3.DISASSEMBLY 3-1.Disassembly Flow .7 3-2.Case (414535) .8 3-3.S-VIDEO board, VIDEO Board, UP CONVERT Board and Tuner.8 3-4.VIDEO.AU Board .9 3-5.DIGITAL Board .9 3-6.MAIN Board, MIX Board . 10 4.TEST MOD

27、E. 11 5.ELECTRICAL ADJUSTMENT. 12 6.DIAGRAMS 6-1.Block Diagram TUNER/VIDEO INPUT Section . 13 6-2.Block Diagram AUDIO DSP Section . 14 6-3.Block Diagram AUDIO CONTROL Section . 15 6-4.Block Diagram POWER AMP Section . 16 6-5.Block Diagram DISPLAY/KEY CONTROL Section . 17 6-6.Block Diagram POWER SUPP

28、LY Section . 18 6-7.Note for Printed Wiring Boards and Schematic Diagrams . 19 6-8.Schematic Diagram DIGITAL (1/5)/V3-OPT Boards . 21 6-9.Schematic Diagram DIGITAL Board (2/5) . 22 6-10. Schematic Diagram DIGITAL Board (3/5) . 23 6-11. Schematic Diagram DIGITAL Board (4/5) . 24 6-12. Schematic Diagr

29、am DIGITAL Board (5/5) . 25 6-13. Printed Wiring Board DIGITAL Board (Component Side) . 26 6-14. Printed Wiring Boards DIGITAL (Conductor Side)/V3-OPT Boards . 27 6-15. Printed Wiring Board VIDEO Board . 28 6-16. Schematic Diagram VIDEO Board . 29 6-17. Printed Wiring Boards S-VIDEO/VIDEO 3/VIDEO.AU

30、 Boards . 30 6-18. Schematic Diagram S-VIDEO/VIDEO 3/VIDEO.AU Boards . 31 6-19. Printed Wiring Board UP CONVERT Board . 32 6-20. Schematic Diagram UP CONVERT Board . 33 6-21. Printed Wiring Board MAIN Board . 34 6-22. Schematic Diagram MAIN Board (1/3) . 35 6-23. Schematic Diagram MAIN Board (2/3) .

31、 36 6-24. Schematic Diagram MAIN Board (3/3) . 37 6-25. Printed Wiring Boards BIAS/MIX Boards . 38 6-26. Schematic Diagram BIAS/MIX Boards . 39 6-27. Printed Wiring Boards H.P/SP/SP-B Boards . 40 6-28. Schematic Diagram H.P/SP/SP-B Boards . 41 6-29. Printed Wiring Board DISPLAY Board . 42 6-30. Sche

32、matic Diagram DISPLAY Board . 43 6-31. Printed Wiring Boards MUTING/POWER/SW Boards . 44 6-32. Schematic Diagram MUTING/POWER/SW Boards . 45 6-33. Printed Wiring Boards AC/DC 1/DC 2/V.SWITCH Boards . 46 6-34. Schematic Diagram AC/DC 1/DC 2/V.SWITCH Boards . 47 6-35. IC Pin Function Description . 58

33、7.EXPLODED VIEWS 7-1.Case Section . 70 7-2.Front Panel Section-1. 71 7-3.Front Panel Section-2. 72 7-4.Chassis Section-1 . 73 7-5.Chassis Section-2 . 74 7-6.Chassis Section-3 . 75 7-7.Chassis Section-4 . 76 7-8.BIAS Board Section. 77 7-9.MAIN Board Section . 78 7-10. Foot Section . 79 8.ELECTRICAL P

34、ARTS LIST. 80 TABLE OF CONTENTS 5 STR-DA2ES/DB1080 SECTION 1 SERVICING NOTES MODEL IDENTIFICATION Back Panel PART No. ModelPART No. DA2ES : US model4-239-175-0 DA2ES : Canadian model4-239-175-1 DB1080: Singapore and Malaysia models 4-239-175-2 DB1080: AEP and UK models4-239-175-3 DB1080: E model4-23

35、9-175-4 DB1080: Korean model4-239-175-5 SERVICE POSITION In checking the DIGITAL board, prepare jig (extension cable J-2501-208-A: 200 mm 21 core). Connect jig (extension cable J-2501-208-A) to the MAIN board (CN806, CN807) and DIGITAL board (CN1102, CN1103). Note:The power cord can be used unplugge

36、d from the back panel though, as it is hard to do it, it is easier to prepare other power cord and use it as a jig. DIGITAL board MAIN board power cord 6 STR-DA2ES/DB1080 SECTION 2 GENERAL This section is extracted from instruction manual. LOCATION OF CONTROLS Front Panel ANALOG DIRECT qh AUDIO SPLI

37、T 0 AUTO DEC ql CINEMA STUDIO EX wd Cursor buttons (/) ej CUSTOMIZE r; Digital Cinema Sound indicator 5 DIGITAL CONCERT HALL ws DIMMER wh DISPLAY 3 Display 7 DOOR OPEN qf ENTER eh EQ ek EQUALIZER es FM/AM wa FM MODE rf FUNCTION qs INPUT MODE qd IR receptor 2 Jog dial eg LEVEL ef MASTER VOLUME 9 MEMO

38、RY e; MODE +/ qj MULTI CH DIRECT qg MULTI CHANNEL DECODING indicator 8 MUTING qa NIGHT MODE ra NIGHT MODE indicator 4 NORMAL SURR (;PLII/NEO 6) wg ON SCREEN wj PHONES jack wk PRESET TUNING +/ w; RDS PTY rd (Models of area code CEL, CEK only) SB DEC indicator 6 SET UP ed SLEEP rd (Models of area code

39、 SP, KR, E only) SPEAKERS switch wl SURR el SURR BACK DECODING wf TEST TONE rs TUNING +/ ea (Models of area code U, CA, SP, KR, E only) TUNING/PTY SELECT +/ ea (Models of area code CEL, CEK only) VIDEO 3 INPUT jacks rg (16) 2CH STEREO qk 2ND ROOM rd (58) (Models of area code U, CA only) ?/1 (power)

40、1 + + + 1 23 4 5 6789 q;qaqsqdqfqgqhqjql qkw;wawgwhwjwkwlwfwd ws e;eaes ed efeg ejr; el raehekrsrgrdrf 7 STR-DA2ES/DB1080 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY SET 3-3. S-VIDEO BOARD, VIDEO BOARD, UP CONVERT BOARD AND TUNER (Page 8) 3-2. CA

41、SE (414535) (Page 8) 3-5. DIGITAL BOARD (Page 9) 3-6. MAIN BOARD, MIX BOARD (Page 10) 3-4. VIDEO AU BOARD (Page 9) 8 STR-DA2ES/DB1080 Note: Follow the disassembly procedure in the numerical order given. 3-2.CASE (414535) 3-3.S-VIDEO BOARD, VIDEO BOARD, UP CONVERT BOARD (DA2ES) AND TUNER 1two flat he

42、ad screws 1two flat head screws 1two flat head screws 1two flat head screws 3case (414535) 2 2 1connector (CN853) 4S-video board, video board and up convert board (DA2ES) 2wire (flat type) (15 core) (DB1080) wire (flat type) (21 core) (DA2ES) (CN303) 5wire (flat type) (15 core) 3six screws (BV/RING)

43、 6three screws (BV/RING) 3two screws (BV/RING) (except DB1080: AEP, UK models) 7tuner 9 STR-DA2ES/DB1080 3-4.VIDEO.AU BOARD 1wire (flat type) (9 core) (DB1080) wire (flat type) (15 core) (DA2ES) (CN201) 4video AU board 2connector (CN202) 3two screws (BV/RING) 3screw (BV/RING) (DB1080: AEP, UK models) 3screw (BV/RING) (DA2ES) 3-5.DIGITAL BOARD 1wire (flat type) (31 core) (CN1101) 2four connectors (CN1106, CN1108, CN1109, CN1110) 6five screws (BV/RING) 8digital board 7two connect