Tandberg-62-X-Service-Manual电路原理图.pdf

《Tandberg-62-X-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Tandberg-62-X-Service-Manual电路原理图.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、January 1967 TANDBERG TAPE.RECORDER Models 64x and 62x Alignment instruction for heads and electronics Preface The models 64x and 62x are improved versions of has been introduced to improve the frequency re- the earlier models 64-62 and this alignment instruc- sponse and the signal to noise ratio. t

2、ion is an appendix to the service manual for model The oscillator has been redesigned and fully transis- 64:-62. lt covers the special head alignments and torized. Certain minor changes have been introduced electrical adjustments necessary for model 64x and in the equalization circuits, mainly chang

3、es of com- 62x. ponent values. A microswitch is further introduced in the bias circuit to reduce the bias in 1.7/e i. p.s. The models 64x and 62x have the same operation tape speed. This switch is operated automatically by facilities as 64-62. A new, and separate bias head the speed selector mechani

4、sm. See fig. 3. Ti.d.*.q r=r=rErlEr/ TANDBERGS RADIOFABRIKK A/S OSLO NORWAY RadioFans.CN 收音机爱 好者资料库 1.0 Alignment It is important that the contact between the tape and the heads on the tape recorder is good. To obtain this contact the tape should be run through the tape recorder 5-10 times at normal

5、 speed to have the tape polished before measuring the frequency re- sponse and the signal to noise ratio. 1.0.1 Demagnetizing Demagnetize the heads and adjacent parts before aligning the heads. 1.0.2. The mounling plate lor the heads The height of the mounting plate for the heads (15.4) is aligned b

6、y the adjustment screw at the rear of the playback head. Move the operating lever slowly to normal forward drive with a tight tape inserted. Align the height of the mounting plate for the heads until the tape runs equidistant from the flanges of the tape guide (79,2). 1.0.3 The adjustable tape guide

7、 Set the operating lever in normal forward drive with tape inserted and depress the push-button lll. Align the adjustable tape guide (79.3) until the tape runs equidistant from the flanges of the adjustable tape guide. Repeat 1.0.2. 2.O Adjustment of the oscillator and bias head circuits. 2.0.1 Inse

8、rt one 10 ohm resistor in series with each bias head half to ground and connect a V.T.V.M. across each resistor. 2.O.2 R 609 and R 612 is turned up to 1 oclock posi- tion while R607 and R610 are set to approx. 11 oclock. Rel. fig. 3. 2.0.3 Set the tape recorder to stereo recording and the speed sele

9、ctor to 7tlu i.p.s. 2.0.4 Use a calibrated long wave receiver, frequency meter or frequency counter for the indication and adjust the oscillator frequency by C 610 until f/osc. = 85.5 kc/s. 2.0.5 Set the tape recorder for mono recording CH 1 and the speed selector to 7tlz i.p,s. 2.0.6 Adjust the osc

10、illator frequency with L601 F/osc. will then be 85.5 kc/s. 2.0.7 Set the tape recorder for mono recording CH 2. 2.0.8 Readjust L 601 to compromise if necessary. The osc. frequency deviation between mono recording CH 1, CH 2 and stereo should be less than 2 kc/s. The deviation should be indicated wit

11、h frequency meter, long wave receiver or frequency counter. 2.0.9 Adjust C 602 and 604 to max. reading on the V.T.V.M. (between 100 mV and 400 mV). 3.0 Head alignment and track control with Tandberg Test Tapes, Model 64x 3.1. The playback head 3.1.1 Connect one V.T.V.M. to each CATHODE FOLLOWER outp

12、ut. 3.1.2 Height alignment: Play back the test tape No. 1. This is a full track pre-recorded tape with 1000 c/s recorded atTt/zi.p.s. tape speed. The record level of the exact area corresponding to track 3 is reduced 30 dB. Adjust the height of the playback head until minimum output is botained on a

13、 V.T.V.M. from track 3 (ch. 2). 3.1.3 Azimuth alignment: Play back the test tape No. 2. This is a full track pre-recorded tape with 10.000 cls al 71lz i.p.s. tape speed. Adjust the azimuth position of the playback head until maximum reading is obtained on both output meters. 3.1.4. Lateral alignment

14、: Check the lateral position of the playback head by pulling the pressure pad (59.5) away from the erase head when the test tape No. 2 is played back. The output level should not decrease more than 3 dB. Adjust the lateral position of the playback head, is necessary, by turning the head mounting pla

15、te. Re- adjust the azimuth position. 3.2 The record head. 3.2.1 Adjust the horizontal position of the bias head until the head is in center of the record head. Ref. fig. 1. 3.2.2 Adjust the height of the bias head until the tape runs freely in the groove in front of the bias head. 3.2.3 Height align

16、ment: The record head is set in a preliminary position where approx. 0.1 mm (.0025) of the lamination for the upper track is visible above the tape. The position of the record head can be inspected by using the iron powder method (Magna-See). Record all four tracks on the tape and dip the tape in th

17、e solution. The pattern on the tape will show il the position of the head is correct. Readjust if necessary. 3.2.4 Azimuth alignment: Connect a signal generator to the HI-LEVEL inputs CH1 and CH2, and two V.T.V.M. to the CATHODE FOLLOWER outputs CH1 and CH2. Make a stereo recording in B-test al 7t/z

18、 i.p.s. of a 15.000 c/s signal. Adjust the azimuth of the record head to max. reading on the output meters. The out- put level should now be approx. 100 mV with the playback volume controls to max., readjust the record gain controls until this is obtained and check the azimuth position of the record

19、 head. 3.2.5 Lateral alignment: Check the lateral position of the record head by pulling the pressure pad (59.5) away from the erase head during the recording. The output level should not decrease more than 3 dB. Adjust the lateral position of the record head, if necessary, by turning the head mount

20、ing plate. Recheck the height and azimuth position of the head. Ref. para. 3.2.3 and 3.2.4. 3.3 The bias head. 3.3.1 Heighl alignment: Connect two V.T.V.M. directly across the recording heads. Set the tape recorder to stereo recording at 71 lz i.p.s. and turn both playback volume controls down to 0.

21、 RadioFans.CN 收音机爱 好者资料库 Adjust the height of the bias head by the height adjustment screw (ref. fig. 1) until max. reading is obtained on both V.T.V.M. Check that the tape runs freely in the groove in front of the bias head and that there is sufficient clearance between the bias head and the mounti

22、ng plate for the record head. The height position of the bias head is not critical, and if the clearance between the bias head and the mounting plate for the record head is insufficient, raise the bias head slightly. 3.3.2 Horizontal alignment: Connect two V.T.V.M. to both CATHODE FOLLOWER outputs,

23、and connect a signal generator to the Hl- LEVEL inputs CHI and CH2. Set the tape recorder to stereo recording al 71lz i.p.s. and turn both play- back volume controls to max. Record a 1000 c/s signal. Untighten the fixing screw for horizontal adjustment (ref. fig. 1) and move the bias head from the e

24、xtreme Ieft position towards the recording head until max. reading is obtained on both V.T.V.M. The output level should now be approx.5V, readjust the record gain controls until this is obtained and check the horizon- tal position of the bias head. After one has assured that the horizontal position

25、is correctly adjusted, tighten the adjustment screw making sure that the head is not being moved. This is eventually indicated by a loss of the output level. A fine-adjustment of the bias current is obtained by the pot.meters R609 (CH1) and R612 (CH2). Adjust R 609 and R 612 until max. reading on th

26、e optput meters are obtained. 3.4 The erase head. 3.4.1 Height adjustment: The erase head is set in a preliminary position where approx. 0.25 mm (.01) of the ferrite core for the upper track of the erase head is visible above the tape. Insert the test tape No. 9 and record a 1000 c/s signal from the

27、 generator on ch. 2 at maximum re- cording level. Dip the tape in the Magna-See solution and check that the re-recorded track lies in center of the erased track. Make sure that the erase head does not erase any part of the adjacent tracks. 3.4.2 Azimuth alignment: Align the azimuth position of the e

28、rase head by the azimuth adjustment screw. The erase head should be parallel with the mounting plate for the heads (15.4). The azimuth position of the erase head is not critical. 3.4.3 Lateral alignmenl: Turn the head mounting plate for the erase head, until the front of the head is parallel to the

29、pressure pad. 3.5 Model 62x. 10 000- 5000 - 1C00 - 100- 50-250 c/s recorded at71/t i.p.s. tape speed. The tape conforms with the N.A.B. standards. The output tolerance is -+ 2 dB for all frequencies. The difference in level between the two channels should be less than 3 dB. 4.2 Adjustment of the pla

30、yback amplifiers: Play back the test tape No. 4 with the output volume controls to maximum. This is a full track prerecorded tape with 400 c/s at71/z i.p.s. tape speed. Ad.just the potentiometers R233 (CH 1) and R234 (CH 2) until the reading on the output meters are 1.3V. 5.0 Adjustment of the recor

31、d current (A-B test) and the electronic beam indicators. Make sure that all adjustments under paras 1.0, 2.0 and 3.0 are made before proceeding with these ad- justments. Connect a signai generator to both Hl-LEVEL inputs and two V.T.V.M. to both CATHODE FOLLOWER out- puts. Record a 4O0 cls signal in

32、 stereo A-test, with both playback volume controls to max. at 7tlz i.p.s. Adjust the record levels by the record gain controls until the output levels are 1.5 V. Depress the push-buttons lV and V (stereo B-test) and adjust the record current by R115 (CHl) and R116 (CH2) until the readings on the out

33、put meters are 1.5 V. Adjust R 137 (CHl) and R 138 (CH2) until the elec- tronic beam indicators are closing. Release the push- buttons lV and V (stereo A-test) and check that the readings still are 1.5 V on the output meters. 6.0 Head alignment without Tandberg Test Tapes. 6.1 The playback head. 6.1

34、.1 Height alignnnent: The height of the playback head is aligned by the height adjustment screws. The upper edge of the tape shall run flush with the upper part of the airgap for channel 1. 6.1.2 Azimuth alignmenl: Play back a standard azimuth alignment tape with a V.T.V.M. connected to each cathode

35、 follower output. Adjust the position of the playback head by the azimuth adjustment screw, until maximum reading is obtained on the output meters. 6.1.3 Lateral alignment: Pull the pressure pad (59.5) away from the erase head when the standard azimuth alignment tape is being played back. The output

36、 level should not decrease more than 3 dB. Adjust the lateral position of the playback head, if necessary, by turning the head mounting plate. All the alignments specified in chapters 3.1, 3.2, 3.3, 6.2 The record bead. and 34 are valid for model 62x with the exception-o1 iorro*inl instructions give

37、n under para3.z. paragraph 3.1.2 which is superseeded by 6.1.1 and paragraph 3.2.3 is superseeded by 6.6.2. 6.3 The bias head. 4.0 control and adiustment ol playback amplifiers, Follow the instructions given under para 33 with Tandberg test tapes. 6.4 The erase head. 4.1 Control of the playback ampl

38、ifier: 6.4.1 Height alignment: Play back the test tape No. 3. This is a full track pre- The height of the erase head is aligned by the height recorded tape with the following frequencies:250- adjustment screws. Approx.0.25 mm (.01 ) of the 1 /z .B. all WO me ed ihe :he nd 2.0 rd- uIs ut- )th ust nti

39、l ,ns ent lgs ec- sh- the ferrite core for the upper track of the erase head should be visible above the tape. 6.4.2 Azimuth alignment: Align the azimuth position of the erase head by the azimuth adjustment screw. The erase head should be parallel with the mounting plate for the heads (15.4). The az

40、imuth position of the erase head is not critical. 6.4.3 Lateral alignment: Turn the head mounting plate forthe erase head, until the front of the head is parallel to the pressure pad. 6.5 Track control, model 64x. 6.5.1 The record head: Record a 1000 c/s from a generator at maximum re- cording level

41、 in stereo A-test on track 1 and 3 (push- buttons l, ll and lll depressed) for approx. 5 seconds. Turn the tape around and make a similar recording on track 4 and 2. Cut the tape and dip it in a mixture of iron powder and alcohol (Magne-See) to make the recording visible. The spaces between the reco

42、rded tracks should be distributed equidistant across the tape. Readjust the height position, if necessary, and recheck the azimuth alignment. 6.5.2 The erase head: Insert a full-track pre-recorded tape and record a 1000 c/s signal from a generator at maximum record- ing level in mono A-test on track

43、 3 (push-buttons ll and lll depressed). Cut the tape and dip it in the Magne-See solution. Check that the re-recorded track is in the center of the erased area. Adjust the vertical pos. of the erase head if necessary. 6.5.3 The playback head: Record a 1000 c/s signal on track 1 (CH1) and a 500 c/s s

44、ignal on track 3 (CH2) at maximum recording levels. Turn the tape around and play back track 2 (push-buttons lll and V depressed) at maximum vo- lume. No signal should be heard. Raise the playback head if the 1000 c/s signal is heard. Lower the play- back head if the 500 c/s signal is heard. Re-chec

45、k the azimuth position. 6.6 Track control, model 62x. 6.6.1 The erase head: The height of the erase head is aligned by the height adjustment screws. The tape shall run equidistant from the upper and the lower edge of the ferrite core. 6.6.2 The record head: The height of the record head is aligned b

46、y the height adjustment screws. Record a 1000 c/s signal in stereo (push-buttons l, ll and lll depressed) at maximum recording level on a full-track pre-recorded tape. Dip the tape in the Magne-See solution and check that the tracks are distributed symmetrically across the tape, and that the recorde

47、d zone remains in the center of the erased zone. Readjust the erase and the record heads, if necessary. 6.6.3 The playback head: The height of the playback head is aligned by the height adjustment screws. The tape shall run flush with the upper edge of the lamination for channel 1. Readjust the azim

48、uth in necessary. 7.0 Adiustments of the amplifiers, vuithout Tandberg Test Tapes. A V.T.V.M. is connected to each output terminal. The signal generator is connected to the high level inputs of both channels and tuned to 400 c/s. The tape recorder is set up for stereo recording A-test (push-buttons

49、l. ll, and lll depressed with the operat- ing lever in normal fonvard drive position) at 7tlz i.p.s. tape speed. Insert a good quality recording tape. Adjust the recording gain controls until the readings on the output meters are 1.5V with the playback controls to maximum. Replace the V.T.V.M. for channel 1 with a distortion meter and depress the push-button lV (B-test CH1). Adjust the recording current by R 115 until the read- ing shows 3 o/o distortion. Replace the V.T.V.M. for channel 2 with the distortion meter and depress the push-button V (B-test CH2). Adjust the recorder curr