Teac-AGD-9260-Service-Manual电路原理图.pdf

《Teac-AGD-9260-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Teac-AGD-9260-Service-Manual电路原理图.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、A AG G- -D D9 92 26 60 0 SERVICE MANUAL AV Digital Home Theater Receiver Effective : January, 2002S-0000A NOTES PC boards shown are viewed from parts side. The parts with no reference number or no parts number in the exploded views are not supplied. As regards the resistors and capacitors, refer to

2、the circuit diagrams contained in this manual. Parts marked with this sign are safety critical components. They must be replaced with identical components - refer to the appropriate parts list and ensure exact replacement. Parts of mark can be used only with the version designated. US:U.S.A. C:CANAD

3、A E:EUROPE UK:U.K. RadioFans.CN 收音机爱 好者资料库 2 CONTENTS SPECIFICATIONS.3 SAFETY INSTRUCTIONS .4 MEASUREMENTS AND ADJUSTMENTS .5 FIP DISPLAY .8 DISPLAY PIN CONNECTION .9 IC BLOCK DIAGRAMS AND PIN FUNCTIONS .10 EXPLODED VIEWS AND PARTS LIST .22 PC BOARDS AND PARTS LIST .24 INCLUDED ACCESSORIES .29 Radio

4、Fans.CN 收音机爱 好者资料库 3 SPECIFICATIONS Amplifier Section Surround Output Power (0.9 % THD, 1 kHz, 8 ohms): 100 + 100 watts (Front) 100 watts (Center) 100 + 100 watts (Rear) Delay Time: DOLBY DIGITAL: REAR 0 15 ms CENTER 0 5 ms DOLBY PRO LOGIC: REAR 15 30 ms Audio Input Sensitivity/Impedance: *LINE: 220

5、 mV/47 k ohms Output Level/Impedance: CD-R/TAPE REC: 200 mV/2.2 k ohms Frequency Response: *LINE: 20 Hz 65 kHz, +1/ 3 dB Signal-to-Noise Ratio: *LINE: 95dB (IHF-A) Tone Control: BASS: 10 dB at 100 Hz TREBLE: 10 dB at 10 kHz Digital Audio Section Sampling Frequency:32 kHz, 44.1 kHz, 48 kHz, 96 kHz DI

6、GITAL Input Level/Impedance: DIGITAL 1, 2 (OPTICAL): 15 dBm 21 dBm DIGITAL 3 (COAXIAL): 0.5 Vp-p / 75 ohms FM Tuner Section (Without notes 100.1 MHz, 65 dBf) Tuning Range: 87.5 MHz 108.0 MHz (50 kHz steps, us/c:100kHz steps) Usable Sensitivity (IHF): Mono: 11.2 dBf 50 dB Quieting Sensitivity: Mono:

7、15.3 dBf Stereo: 38.5 dBf Capture Ratio:2.0 dB Image Rejection Ratio: 80 dB ( us/c: 45dB ) AM Suppression Ratio: 55 dB Total Harmonic Distortion (1 kHz): Mono: 0.4% Stereo: 0.5% Frequency Response:30 Hz 15 kHz, +1/ 1.5 dB Stereo Separation (1 kHz):40 dB Signal-to-Noise Ratio: Mono: 75 dB Stereo: 70

8、dB AM Tuner Section Tuning Range: 522 kHz 1,620 kHz (10 kHz steps) 539 kHz 1,720 kHz (10 kHz steps: us/c ) Usable Sensitivity:55 dB/m Total Harmonic Distortion:0.8% at 85 dB/m Signal-to-Noise Ratio:45 dB at 85 dB/m Video Section Input Sensitivity/Impedance:1.0 Vp-p/75 ohms Output Level/Impedance:1.0

9、 Vp-p/75 ohms General Power Requirements: E/UK : 230V AC, 50Hz US/C : 120V AC, 60Hz Power Consumption: E/UK : 300W US/C : 2.8A AC Outlets: Switched x 2, Total 100 W max. (1 A max.) (U.S.A./Canada model) Dimensions (W x H x D) 435 x 165 x 350 mm (17-1/8 x 6-1/2 x 13-3/4) Weight (net): E/UK : 9.5kg US

10、/C : 9.4kg(20-11/16lb) Standard Accessories: AM Loop Antenna x 1 FM T-type Antenna x 1E/uk FM T-type Antenna x 1 Remote Control Unit (UR-417) x 1 *LINE means CD, CD-R/TAPE, VCR/VIDEO 1, DBS/VIDEO 2, DVD/VIDEO 3 and AUX/VIDEO 4. Improvements may result in specifications and features changing without

11、notice. Illustrations may differ slightly from production models. 4 SAFETY INSTRUCTIONS PRECAUTIONS DURING SERVICING 1. Parts identifide by the ( )symbol parts are critical for safety. Replace only with parts number specified. 2. In addition to safety, other parts and assemblies are specified for co

12、nformance with such regulations as those applying to spurious radiation. These must also be replaced only with specifide replacements. Examples :RF converters, tuner units, antenna selectswitches, RF cables, noise blocking capacitors, noise blocking filters, etc. 3.Use specified internal wiring. Not

13、e especially : 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads 4. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers(insulating barriers) 4) Insulation sheets for transistors 5) Plastic screws for

14、 fixing micro switches 5. When replacing AC primary side components (transformers, power cords, noise blocking capacitors, etc.), wrap ends of wires securely about the terminals before soldering. 6. Make sure that wires to do not contact heat producing parts (heat sinks, oxide metal film resistors,

15、fusible resistors, etc.). 7. Check that replaced wires do not contact sharp edged or pointed parts. 8. Also check areas surrounding repaired locations. 9. Make sure that foreign objects (screws, solder droplets, etc.) do not remain inside the set. MAKE YOUR CONTRIBUTION TO PROTECT THE ENVIRONMENT Us

16、ed batteries with the ISO symbol for recycling as well as small accumulators (rechargeable batteries), mini-batteries (cells) and starter batteries should not be thrown into the garbage can. Please leave them at an appropriate depot. All other house- hold batteries can be thrown out with the househo

17、ld waste. SAFETY CHECK AFTER SERVICING After servicing, make measurements of leakage-current or resistance in order to determine that exposed parts are acceptably insulated from the supply circuit. The leakage-current measurement should be done between accessible metal parts (such as chassis, ground

18、 terminal, microphone jacks, signal input/output connectors, etc.) and the earth ground through a resister of 1500 ohms paralleled with a 0.15 capacitor, under the units normal working conditions. The leakage-current should be less than 0.5mA rms AC. The resistance measurement should be done between

19、 accessible exposed metal parts and power cord plug prongs with the power switch (if included) ON. The resistance should be more than 2.2M Ohms. PRECAUTIONS IN REPAIRING When repairing or adjusting the unit, please note the following points. 1. Do not put excessive pressure on the mechanical part (o

20、peration part), including the pick-up block, as extremely high mechanical precision is required in these parts. 2. When the base is removed for repair adjustment, make sure that there are no metal obiects in the narrow gap between the P. C. board or the mecha parts and the base 3. The Micro-Computer

21、 and the CD signal processing ICs can be damaged by static electricity or leakage from a soldering iron during repairing. While soldering, please take the precautions against leakage as in the illustration. 4. Do not loosen any screws in the pick-up block. When handing the pick-up block, please refe

22、r to the points to NOTE when replacing the pick-up block. 5. Keep safety for hazardous invisible Laser Radiation, DO NOT watch the Laser Beam (Objective lens) directly. 6. Models for some countries, laser warning labels are affixed on the unit and inside of the unit, as shown below. Read it carefull

23、y for your safety, when repairing or adjusting the unit. GND ALIGNMENT INSTRUCTIONS EQUIPMENT NEEDED: AM Signal Generator FM Signal Generator Oscilloscope VTVM(AC, DC) Test loop antenna (AM Adjustment) Dummy antenna (FM Adjustment) Distortion analyser IMPORTANT 1. Check power-source voltage. 2. Set

24、the function switch to band aligned. 3. Keep the signal input as low as possible to adjust accurately. 4. Modulation and modulation frequency. Item ModulationModulation frequency Band AM30%400Hz FM400Hz ADJUSTMENT POINT MEASUREMENTS AND ADJUSTMENTS 100% (40 kHz Dev.) E/UK 100% (75 kHz Dev.) US AM LO

25、OP ANT ANT TERMINAL CT10 PACK1 IC11 J208 VR11VR13 IC12 T102 FM ANT VR12 J207 J205 L104L105 T101 (FOR UL version) L3 L7 L4 L5 L6 L3 L7 T1 L6 L4L5 L3 L6 L4 FM OSC COIL T1FM IFT FM OFFSET ADJ TP CT10 AM ANT TRIMMER (1503kHz/1510kHz) L104 AM ANT COIL L105 AM OSC COIL T101 FM IFT COIL T102 AM IFT COIL (6

26、12kHz/610kHz) VR13 FM SD ADJUSTMENT VR12 AM SD ADJUSTMENT VR11 FM SEPARATION ADJ J208 FM/AM VT J205 J207 FM ANT COIL FM RF COIL (FOR EUR version) L1 L2 L6 L3 L4 L5 L1L2 L5 L7 IFT FM OSC COILL7 FM ANT COIL FM RF COIL 5 1.TUNING FREQUENCY RANGE ADJUSTMENTS (FM) DC VOLTMETER . CONNECT TO TEST POINT J20

27、8 and GND NO.BandFrequencyAdjust forAdjustment 1FM87.50MHz1.6VL7 2AM530 kHz1VL105 US/C530 kHz1VL105 2.AM TRACKING ADJUSTMENT Signal Generator. Connects to the AM ANT. Coil through the loop antenna. Adjust for the indication of VTVM of the wave form of scope to be maximum. BANDStepFrequencyAdjust for

28、Adjustment 1610 kHzMaximum sensitivityT102, L104 US/C610 kHzMaximum sensitivityT102, L104 21510 kHzMaximum sensitivityCT10 US/C1510 kHzMaximum sensitivityCT10 3Repeat steps 1 and 2 several times. AM J208 3.FM-RF ADJUSTMENT Signal Generator. Connect to FM ANT JACK (FM IN) through the dummy. NO.Freque

29、ncyAdjust forAdjustment 190.10MHzMaximum SensitivityL3, L5, L6 2Repeat step 1 several times. 6 4.FM MONO DISTORTION ADJUSTMENT DC VOLT METER.Connect to J205 (-), J207 (+) through the chock coil (100uH). Signal Generator.Connect to FM ANT Jack (FM IN) through the dummy. Distortion Meter .Connect to t

30、he output. NO.FrequencyAdjust forAdjustment 1100.10MHz 2100.10MHz 3Repeat steps 1 and 2 several times. 5.FM/AM AUTO STOP LEVEL ADJUSTMENT FM Signal Generator.Connect to FM ANT Jack (FM IN) through the dummy. AM Signal Generator.Connect to AM ANT. Coil through the Loop antenna. J205 J207 DC Voltmeter

31、 0V Minimum T.H.D 7 DC Voltmeter 0VT101 T101 BANDStep Signal Generator Adjust for Adjustment 1 990KHz 82dB Display ON VR12 US/C990KHz 2 990KHz 81dB Display OFFVR12 US/C990KHz 1 100.1MHz 32dBDisplay ON VR13 2 100.1MHz 31dB Display OFF VR13 TUNED TUNED TUNED TUNED AM FM 8 10G9G8G7G6G5G4G3G2G1G P1SOURC

32、Ed2d2d2d2d2d2d2d2kHz P2AUXd1d1d1d1d1d1d1d11d P3LDeeeeeeee1e P4DVDrrrrrrrr1c P5VCR 1pppppppp1g P6RECnnnnnnnn1f P7cccccccc1b P8SP.ffffffff1a P9AggggggggM P10Bmmmmmmmm2d P11CHURCHhhhhhhhh2e P12DISCOjjjjjjjj2c P13STADIUMkkkkkkkk2g P14HALLbbbbbbbb2f P15THEATERa2a2a2a2a2a2a2a22b P16PCMa1a1a1a1a1a1a1a12a P

33、17AC-3S1S1S1S1S1S1S1S1DELAY.T P18STEREOS2S2S2S2S2S2S2S2PRESET CH. P193S3S3S3S3S3S3S3S3MEMO P20S4S4S4S4S4S4S4S4TAPE P21DIGITALRDSDpTAMHz P22PRO LOGICDTSTUNEDSTEREOPTYRTTPmS ANODE CONNECTION FIP DISPLAY 9 Pin No.4647 F1F1 Pin No.313233343536373839404142434445 NXNXNXNX1G2G3G4G5G6G7G8G9G10GNP Pin No.161

34、718192021222324252627282930 P14P13P12P11P10P9P8P7P6P5P4P3P2P1NX Pin No.123456789101112131415 F2F2NPNXNXNXNXP22P21P20P19P18P17P16P15Connection Connection Connection Connection PIN CONNECTION 471 PIN No.SYMBOLI/ODESCRIPTION 1,25VDD-Power Supply Port(+5V) 2,3Function SW1,SW2IFunction Encoder Control Po

35、rt 4Speaker ON/OFFOFront Speaker Relay Drive Port(“H”) 5NC-Not Use(No connection) 6DSP ResetOReset (Initial Clear) Port for YSS912 7Surr. CLKOSurr. CLK Output Port 8DATA OUTOData Output Port for YSS912 9Surr. DATAOSurr. DATA Output Port 10CSOChip Selector Port for YSS912 11CSOChip Selector Port for

36、AK4112 12CSBNOSub DSP Chip Selector for YSS912 13,14RDS CLK/DATAIRDS IC(SA6579TV1) CLK/DATA Port 15Stereo INIStereo Display Control Port(L) 16Tuned INITuned Display Control Port(L) 17 21KEY MatrixIResistor Divide Key Control Input (17,18 Pin: NOT USE) 22,30Vss-Device GND Port 23Vass-Device Analog GN

37、D Port 24Varef-A/D Converter Reference Voltage 26BACKUPIBack Up Mode Control Input 27TEST-NC(GND) 28,29VOLUME UP/DOWNIMaster Volume Up/Down Control Port 31X INI 8MHz Crystal Connection Port 32X OUTO 33RESET (L)IReset Input 34REMOTE INIRemote Control Sensor Data Input 35BUS IN(NC)ISystem Remote Contr

38、ol Input(No Connection) 36HEADPHONE INOHeadphone JACK INPUT(“H”) - Connet to GND 37E.VOL.DATAO 38E.VOL.CLKIElectronic Vol. IC(M62446FP) DATA/CLK/STB Port 39E.VOL.CEO 40PLL.DATA INIPLL IC (LC72131) DATA Input Port 41PLL.CEOPLL IC (LC72131) Chip Enable Control Port 42DATA 3OFunction IC Data Input Port

39、 43CLK 3OFunc./PLL IC CLK Control Port 44FUNC. STBOFunction Strobe Control Output 45FUNC. MUTEOFunction Mute Control Output(“H”) 46SURR. MUTEOSurrounc Mute Control Output(“H”) 47Power ON/OFFOPower ON/OFF Control Port(H) 48SURR. HOSurr. ON/OFF Contol Port(H) 49PROTECT INIProtect Input Port(L) 50FIP V

40、kk-FIP (FLT) -28V Negative Power Supply For FIP Blinking 51 60FIP GridOFIP (FLT) Grid Control Outputs 61 82FIP SegmentOFIP (FLT) Segment Control Outputs 83 86OptionlArea/Function Option Ports 87 94N.C-Not Use(No connection) 95SUB. LEDOSubwoofer LED Drive Port 96MUTE LEDOMUTE LED Drive Port 97 99VIDE

41、D A/B/COVideo IC(NJM2296M/LA7952) Control Ports 100N.C-Not Use(No connection) IC PIN FUNCTION (u-COM : ANAM1308AT,O.T.P :TMP87PM78F) : IC71 10 11 PIN No.SYMBOLI/ODESCRIPTION 1,31,71 2 3 4 5 6 7 8 9 10, 30 11 12 13 14 15 16 17 18 19 20 21,41,51,81,91 22 23 24 25 29 32 35 36 39 40,50,60,80,90,100 42 4

42、4 45 47 48 49 52 53 54 55 56 57 58 59 61 62 63 64 65 66 67 68 69 VDD1 RAMCEN RAMA16 RAMA15 SDIB0 SDIB1 SDIB2 XI XO VSS AVDD SDIB3 TEST TEST OVFB DTSDATA AC3DATA SDOB3 CPO AVSS VDD2 SDOA2 SDOA1 SDOA0 RAMA 1410 OPORT 03 OPORT 47 VSS RAAM 97 SDOB 20 SDBCK1 SDWCK1 NONPCM CRC MUTE KARAOKE SURENC /SDBCK 0

43、 RAMA6 RAMA5 RAMA4 /IC TEST RAMA3 /CSB /CS SO SI SCK - O O O I+ I+ I+ I+ O - - I+ - - O O O O A - - O O O O O O - O O I+ I+ O O O O O O O O O Is - O Is+ Is Ot Is Is +5V Power Supply(for I/Os) External SRAM interface /CE External SRAM interface address 16 External SRAM interface address 15 PCM input

44、0 to Sub DSP(not use) PCM input 1 to Sub DSP(not use) PCM input 2 to Sub DSP(not use) Crystal oscillator connection(12.288MHz) Ground +3.3V power supply (for PLL circuit) PCM input 3 to Sub DSP(not use) Test terminal(to be open in normal use) Test terminal(to be open in normal use) Detection of over

45、flow at Sub DSP (not use) Detection of DTS data (not use) Detection of AC-3 data (not use) PCM output from Sub DSP Output terminal for PLL,to be connected to ground through the external analog filter circuit Ground for PLL circuit) +3.3V power supply (for core logic) PCM output from Main DSP (C,LFE)

46、 PCM output from Main DSP (LS,RS) PCM output from Main DSP (L,R) External SRAM interface address 1410 Output port for general purpose Output port for general purpose (not use) Ground External SRAM interface address 97 PCM output from Sub DSP Bit clock input for SDOA,SDIB,SDOB (not use) Word clock input for SDOA