Yamaha-CDS-300-Service-Manual电路原理图.pdf

《Yamaha-CDS-300-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS-300-Service-Manual电路原理图.pdf（57页珍藏版）》请在收音机爱好者资料库上搜索。

1、CD-S300 Copyright 2009 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. 1 0 11 4 6 SERVICE MANUAL IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their

2、service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated. WARNING: Failure to follow appropriate service and safety procedures when servic

3、ing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service rep

4、resentative. IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate

5、and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should

6、 any discrepancy appear to exist, please contact the distributors Service Division. WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to th

7、is buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTS TO SERVICE PERSONNEL .23 PREVENTION OF ELECTROSTATIC DISCHARGE .4 FRONT PANEL .5 REAR PANELS .56 REMOTE CONTROL PANEL .7 SPECIFICATIONS / 参考仕様 .8 INTERNAL VIE

8、W .9 DISASSEMBLY PROCEDURES / 分解手順 .1012 TEST MODE / .1314 FACTORY MODE / .15 UPDATING FIRMWARE / 書込 .1621 DISPLAY DATA .22 IC DATA .2330 PIN CONNECTION DIAGRAMS .3132 BLOCK DIAGRAM .33 PRINTED CIRCUIT BOARDS .3440 SCHEMATIC DIAGRAMS .4145 REPLACEMENT PARTS LIST .4755 REMOTE CONTROL .56 09.09 P.O.Bo

9、x 1, Hamamatsu, Japan COMPACT DISC PLAYER CD-S300 RadioFans.CN 收音机爱 好者资料库 2 CD-S300 CD-S300 “CAUTION” “F801: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 500mA, 250V FUSE.” CAUTION F801: REPLACE WITH SAME TYPE 500mA, 250V FUSE. ATTENTION F801: UTILISER UN FUSIBLE DE REC

10、HANGE DE MME TYPE DE 500mA, 250V. This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected cont

11、act between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. 1. Critical Components Information Components having

12、special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated

13、from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15 F. 本機搭載基板付 接合部無鉛付。 無鉛種類、修理時 下記無鉛使用推奨。 Sn+Ag+Cu（錫 + 銀 + 銅） Sn+Cu（錫 + 銅） Sn+Zn+Bi（錫 + 亜鉛 + ） 注意： 無鉛融点温度通常鉛入比 30 40程度高、 合 使用。 All of the P.C.B.s installed in this unit and solder joints are soldered using the lead f

14、ree solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free so

15、lder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities. WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE

16、 TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! About lead free solder / 無鉛 WARNING: Laser Safety This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from las

17、er radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet away from the laser pick-up unit at all times. Do not stare at the laser beam at any time. 2) Do not at

18、tempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. RadioFans.CN 收音机爱 好者资料库 3 CD-S300 CD-S300 R, A, G, L,

19、 J modelsT model Laser Emitting conditions: 1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the lase

20、r pick-up unit. Do not attempt any servicing during this period! If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions. 2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been

21、 set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device. Type: GaAlAs Wavelength: 790 nm Laser output: max. 1.23 W * * This

22、 output is the value measured at a distance of about 200 mm from the objective lens surface on the Optical Pick-up Block. Laser Diode Properties The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This prima

23、ry area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing the player. Service personnel have to take precautions to prevent touching this area or components in this area. Note: The screws on the DVD mechanism may never be touched, removed or re-ad

24、justed. Handle the DVD mechanism with care when the unit has to be exchanged! The DVD mechanism is very sensitive for dropping or giving shocks. Warning for power supply 4 CD-S300 CD-S300 Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly a

25、re called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge

26、 (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock rea

27、sons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to

28、solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges

29、sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive ma

30、terial). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other s

31、afety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). Grounding

32、 for electrostatic breakdown prevention 1. Human body grounding. Use the antistatic wrist strap to discharge the static electricity from your body. 2. Work table grounding. Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet. Caution:

33、The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup. PREVENTION OF ELECTROSTATIC DISCHARGE 1M-ohms Conductive material (sheet) or steel sheet Anti-static wrist strap 5 CD-S300 CD-S300 FRONT PANEL R, T, A,

34、G, L, J models R model T model REAR PANELS A model 6 CD-S300 CD-S300 L model G model J model 7 CD-S300 CD-S300 REMOTE CONTROL PANEL CDX8 8 CD-S300 CD-S300 Audio Section / 部 Output Level / 出力 (1 kHz, 0 dB) .2.0 0.3 V Signal to Noise Ratio / 信号対雑音比 . 105 dB or more Dynamic Range / . 96 dB or more Tota

35、l Harmonic Distortion / 歪率 (1 kHz) .0.003 % or less Frequency Response / 周波数特性 (2 Hz to 20 kHz) . 0.5 dB Digital Output Terminal / 出力端子 .Optical x 1 Coaxial x 1 Other Output Terminal / 他出力端子 .Analog out L/R USB General / 総合 Power Consumption / 消費電力 .13 W Power Supply / 電源電圧 R, L models . AC 110/120/

36、220/230240 V, 50/60 Hz T model .AC 220 V, 50 Hz A model .AC 240 V, 50 Hz G model .AC 230 V, 50 Hz J model .AC 100 V, 50/60 Hz Dimensions (W x H x D) / 寸法（幅高奥行） .435 x 86 x 260 mm (17-1/8 x 3-3/8 x 10-1/4) Weight / 質量 .3.5 kg (7.7 lbs.) Finish / 仕上 Black color .R, T, A, G, L, J models Silver color .R

37、, T, A, G, L, J models Accessories / 付属品 Remote control (CDX8) .x 1 Battery (R6, AA, UM-3) .x 2 Audio pin cable (1.0 m) .x 1 Power cable (1.5 m) .x 1 * Specifications are subject to change without notice due to product improvements. 参考仕様外観予告変更。 R .General model T.Chinese model A .Australian model G

38、.European model L .Singapore model J .Japanese model SPECIFICATIONS / 参考仕様 DIMENSIONS / 寸法図 395 (15-1/2) 435 (17-1/8) 70 (2-3/4) 210 (8-1/4)16 (5/8) 86 (3-3/8) 260 (10-1/4) “iPod” is a trademark of Apple Inc., registered in U.S. and other countries. “Made for iPod” means that an electronic accessory

39、 has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iPod 、米国他国登録 Apple Computer, Inc. 商 標登録商標。 Made for iPod、i

40、Pod 専用接続設計、定 性能基準満認定電子 示。 、機器操作、安全規制基準関一切責任 負。 Unit: mm (inch) 単位：mm（） 9 CD-S300 CD-S300 INTERNAL VIEW OPERATION (7) P.C.B. (R, L models) OPERATION (5) P.C.B. OPERATION (9) P.C.B. MAIN P.C.B. OPERATION (4) P.C.B. OPERATION (6) P.C.B. OPERATION (10) P.C.B. Loader mechanism assy OPERATION (8) P.C.B. O

41、PERATION (2) P.C.B. OPERATION (3) P.C.B. OPERATION (1) P.C.B. 1 2 3 4 5 6 7 8 9 10 11 12 7698 111012 25134 10 CD-S300 CD-S300 Fig. 1 DISASSEMBLY PROCEDURES / 分解手順 (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Top Cover a. Remove 4 screws () and

42、 2 screws (). (Fig. 1) b. Remove the top cover. (Fig. 1) （番号順部品取外。 ） AC 電源、電源抜。 1. 外方 a. 4 本、 2 本外。 （Fig. 1） b. 取外。 （Fig. 1） 2. Removal of Front Panel Ass y a. Using a flatblade screwdriver, move the slider at the bottom in the direction of the arrow shown above. (Fig. 1) Open the disc tray, remove the lid a