Yamaha-CDR-1000-Service-Manual电路原理图.pdf

《Yamaha-CDR-1000-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDR-1000-Service-Manual电路原理图.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL PA 011479 19991025-188000 1.52K-599 Printed in Japan 99.12 HAMAMATSU, JAPAN PROFESSIONAL AUDIO CD RECORDER CONTENTS SPECIFICATIONS. 3 PANEL LAYOUT. 4 BLOCK DIAGRAM. 5 WIRING. 6 CIRCUIT BOARD LAYOUT. 7 DISASSEMBLY PROCEDURE. 8 LSI PIN DESCRIPTION. 10 IC BLOCK DIAGRAM. 12 CIRCUIT BOARDS

2、. 14 TEST PROGRAM. 17/21 ERROR MESSAGES. 25 PARTS LIST OVERALL CIRCUIT DIAGRAM RadioFans.CN 收音机爱 好者资料库 CDR1000 IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the ind

3、ustry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated. WARNING :Failure to follow appropriate service and safety procedures when servicing this product may result in per- sonal injury, destruction of expensive components a

4、nd failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. IMPORTANT :This presentation or sale of this manual to any individual or f

5、irm does not constitute authorization certifi- cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form. The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and servic

6、e departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division.

7、 WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.) IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Rech

8、eck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Healt

9、h and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When sold

10、ering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. WARNING Components having special characteristics are marked and must be replaced with parts hav

11、ing specification equal to those originally installed. RadioFans.CN 收音机爱 好者资料库 WARNING: LASER SAFETY This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the foll

12、owing precaution must be used during servicing of the unit. 1) When testing and / or repairing any component within the product, keep your eyes and skin more than 30cm away from the laser pick-up unit at all time. Do not stare the laser beam at any time. 2) Do not attempt readjustment,disassemble an

13、d repair of the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION - Use of controls or readjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING Laser Diode Properties *

14、Material : GaAlAs * Wavelength : 783789 nm * Emission Duration : Continuous * Laser Output Power : Less than 44.6 W Laser output is measured at a distance of 20cm from the object lens on the optical pick-up head. (Note) When checking the laser diode emission, keep your eyes more than 30 cm away from

15、 the objective lens. This label is located on the interior. Varningsanvisning fr laserstrlning. Placerad i apparaten. CAUTION VARNING VARO! VARNING VORSICHT! : INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. : OSYNLIG LASERSTRLNING NR DENNA DEL R PPEND. STRLEN R FARLIG. : NKYMTNT AVATTA

16、ESSA OLET ALTTIINA LESERSTEILYLLE. L KATSO STEESEEN. : OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD. BETRAKTA EJ STRLEN. : UNSICHTBARE LESERSTRAHLUNG WENN ABDECKUNG GEFFNET. NICHT DEM STRAHL AUSSETZEN. On USA or Canadian models do not have this label. This label is located on the exterior. CLASS 1 LAS

17、ER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT Klassmrkning fr Finland. 3 CDR1000 SPECIFICATIONS Recording media CD-R, CD-RW Playback media CD, CD-R, CD-RW Sampling rate 44.1 kHz Recording resolution 16-bit linear Converters A/D20-bit 64-times oversampling D/A20-bit 128-times oversampling Frequ

18、ency response 20 Hz20 kHz Track Up to 99 tracks Index Up to 99 indexes SRC (Sampling Rate Converter) 30 kHz to 50 kHz UV22 16-bit encoding S/N 97 dB Input delay 04,950 ms Fade in/out time 010 second Synchronized recording CD, MD, DAT Repeat playback One track, All track, AB Locate PREV, NEXT, INDEX,

19、 SEARCH, direct select Display Type VFD (Vacuum Fluorescent Display) Characters 12-character line Time counter Minutes and seconds Display mode Elapse, Remain, Total Track counter 099 Index counter 099 Level meters 16 segment with CLIP indicator x2 Power requirements U.S.A. the display will appear a

20、s shown below and testing will end. DIAG END Exit the TEST mode Turn off the power switch then turn on again. Pressing the SW1 on the MAIN circuit board will set to regular mode. INPUT FREQLEVEL 20 Hz0 dBm+10 dBm +1/-2dB FULL-SCALE,-8.5 +/- 1dB 1 kHz 1 kHz ANALOG OUTCOAXIAL OUT OUT L,RAES/EBS OUT CD

21、R1000 20 6. Recording Playback Distortion Factor Select ANALOG from the INPUT SELECT switch and press the REC key (REC stand-by state). Input a 1 kHz, +8 dB signal into ANALOG IN L and R and check that the distortion factor at ANALOG OUT L and R is less than 0.03%. 7. Recording Playback Residual Noi

22、se Select ANALOG from the INPUT SELECT switch and press the REC key (REC stand-by state). Connect a 150 ohm resistor to the 2-3 pins of ANALOG IN L and R and check that the residual noise at ANALOG OUT L and R is less than -73 dBm. 8. Headphone Output Level, Distortion Factor Select ANALOG from the

23、INPUT SELECT switch and press the REC key (REC stand-by state). Input a 1 kHz, 0 dB signal into ANALOG IN L and R and check that the output level at PHONES OUT, L and R is +3 dBm 2 dB. Also, vary the input level of ANALOG IN L and R so as to obtain the +8 dBm 1 dB (100W output power) at PHONES OUT L

24、 and R and check that the distortion factor is less than 5%. 9. Digital Input Level Select COAXIAL from the INPUT SELECT switch and press the REC key (REC stand-by state). Input a 1 kHz, full-scale signal into COAXIAL IN and check that +18.5 dBm 1 dB signal is output from ANALOG OUT L and R. Also, i

25、nput a 1 kHz, full-scale signal into AES/EBS IN and check that a +18.5 dBm 1 dB signal is output from ANALOG OUT L and R. 10. Recording check Select ANALOG from the INPUT SELECT switch. Press the AUTO button, and then press the REC button (AUTO REC START mode). Input 1 kHz, 0 dBm signals into the AN

26、ALOG IN L and R to record them on the CD-RW disk. Playback the recorded signals to check that the recording has been made properly. CDR1000 21 CDR1000 22 CDR1000 23 CDR1000 24 CDR1000 25 If the CDR1000 displays an error message, follow the instructions below. Error NumberRemarks 062900 1 1. If the e

27、rror cannot be fi xed by opening or closing the disc tray, and the error remains even after powering off and on, change the CDR unit. 062800 020401 023A02 023A03 052000 052400 020408 030C0A 052100 0409XX Change media or failure 2. If the error remains even after powering off and on, repare the Circu

28、it board. 056400 1 2 056401 053008Change media 053100Change media 023005Change media (PMA error) 057301Change media (PMA FULL) 037300Change media (TNO FULL) 031100Change media 0373031 2XXXXX 2 300001 400001 500051 500053 500054 500055 500056 ERROR MESSAGES PROFESSIONAL AUDIO CD RECORDER PARTS LIST C

29、ONTENTS OVERALL ASSEMBLY. 2 FRONT ASSEMBLY. 4 ELECTRICAL PARTS. 6 WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. Notes : DESTINATION ABBREVIATIONS The numbers “QTY” show quantities for each unit.

30、The parts with “-” in “PART NO.” are not available as spare parts. This mark “ ” in the REMARKS column means these parts are interchangeable. The second letter of the shaded () part number is O, not zero. The second letter of the shaded () part number is I, not one. M:South African model O:Chinese m

31、odel Q:South-east Asia model T :Taiwan model U :U.S.A. model V :General export model (110V) W:General export model (220) N,X : General export model Y :Export model A :Australian model B :British model C :Canadian model D :German model E :European model F :French model H :North European model I :Indo

32、nesian model J :Japanese model CDR1000 2 OVERALL ASSEMBLY Front assembly (See page 4) 320 60 80 60 310 320 320 210 130 320 90 380 150 350 140 390 260 400 370 220 230 240 250 280 270 300 290 300 300 300 180 180a180b 100 100 100 190 510 530 500 520 70 200 160 20 30 40 80 110 120 CDR1000 3 : New Parts

33、REF NO.PART NO.DESCRIPTIONREMARKSQTYRANK RANK: Japan only * * * * * * * * * * * * * * * * * * OVERALL ASSEMBLYCDR1000 J,U,V,H,W,B Overall AssemblyJ(V4570900) Overall AssemblyU,V(V4571000) Overall AssemblyH,W(V4571100) Overall AssemblyB(V4571200) 3Earth Film(V521920)2 10Rear Panel JJ 10Rear Panel U C

34、U,C 10Rear Panel H BH,W,B 20Bottom Cover(V405770) 30FootTL-014402 40Bind Head Tapping Screw-B3.0X16 MFZN2BL401 60Bind Head Tapping Screw-BA3.0X8 MFZN2BL601 70Stay(V405760) 80Bind Head Tapping Screw-BA3.0X8 MFZN2BL401 90Circuit BoardMAIN 100Bind Head Tapping Screw-B3.0X8 MFZN2BL1301 110Jack Socket17L

35、-003A3201 120Bind Head ScrewA3.0X6 MFZN2BL01 130Bind Head Tapping Screw-B3.0X6 MFZN2BL301 140Circuit BoardPS JJ 140Circuit BoardPS UU,V 140Circuit BoardPS H,BH,W,B 150Bind Head Tapping Screw-B3.0X8 MFZN2BL401 160Bind Head Tapping Screw-BA3.0X8 MFZN2BL201 180AC-INLET AssemblyACIN 250L(V456760) 180aFe

36、rrite CoreFR25/15/12-1400L04 180bAC-IN ConnectorAC-P01CR0203 190Bind Head Tapping Screw-P3.0X12 MFZN2BL201 200Bind Head Screw4.0X8 MFZN2BL01 210Cord HolderBK-101 220CRW UnitACRW100 220aFront PanelABS 220bTrayPPE X251V BLC1x133 230Tray Panel 240CDR Angle(V405980) 250Bind Head ScrewA3.0X6 MFZN2BL401 2

37、60Bind Head Tapping Screw-BA3.0X6 MFZN2BL401 270Power TransformerJ 270Power TransformerUL CSAU,V 270Power TransformerCEEH,W,B 280Bind Head Tapping Screw-BA4.0X8 MFZN2BL401 285Spacer(V413330)2 290Front Panel Assembly(V457240) 300Bind Head Tapping Screw-BA3.0X8 MFZN2BL801 305Bind Head Tapping Screw-B3

38、.0X8 MFZN2BL201 310Top Cover 320Bind Head Tapping Screw-BA3.0X8 MFZN2BL701 350Wiring AssemblyPSW 340L(V456770) 360Witing AssemblyVR 6P-6P220L(V456800) 370Witing AssemblyCDRW (V456810) 380Witing Assembly AO 230L(V456820) 390Witing Assembly DO 180L(V456830) 400Witing AssemblyMAIN TO CDR(V456840) 410Co

39、nnector Assembly8 250mm C22 J Flame Proof C. Resistor 68.0 1/4 JR:10201 Metal Oxide Film Resistor 33.0 2W JR:10901 Carbon Resistor 1.0K 1/4 JR:10801 Carbon Resistor 3.3K 1/4 JR:105,10601 Carbon Resistor 33.0K 1/4 JR:10101 Carbon Resistor 47.0K 1/4 JR:10401 Carbon Resistor100.0K 1/4 JR:10701 Carbon R

40、esistor680.0 1/4 JR:10301 AC CordDC-015-J01J06 AC CordCSAU,V08 AC CordVDEH,W08 AC CordBSB10 Remote ControllerRC Power TransformerJ Power TransformerUL CSAU,V Power TransformerCEEH,W,B Ferrite CoreFR25/15/12-1400L04 AC-IN ConnectorAC-P01CR0203 CRW UnitACRW100 FanMMS-06E12DL VR796000 V5090300 FI383470

41、 FR203100 HV754680 VC757500 HF756100 HF756330 HF757330 HF757470 HF758100 HF755680 VN391100 VB927800 VB928000 VP204400 V3496500 XV755A00 XV756A00 XV757A00 VC362700 VL785200 V4580100 V4755300 L K J I H G F E D C B A 123456789101112 CDR1000 M N O P Q 123456789101112 Q P O N M L K J I H G F E D C B A CD

42、R1000CDR1000 CDR1000 CIRCUIT DIAGRAM 1/3 (MAIN1/3) L K J I H G F E D C B A 123456789101112 CDR1000 M N O P Q 123456789101112 Q P O N M L K J I H G F E D C B A CDR1000CDR1000 CDR1000 CIRCUIT DIAGRAM 2/3 (MAIN2/3) 12 11 10 9 8 7 6 5 4 3 2 1 ABCDEFGHIJKLMNOPQ 12 11 10 9 8 7 6 5 4 3 2 1 ABCDEFGHIJKLMNOPQ CDR1000 CDR1000CDR1000 CDR1000 CIRCUIT DIAGRAM 3/3(MAIN3/3,FP-1/3,2/3,3/3,PS)