Yamaha-NS-150-Service-Manual电路原理图.pdf

《Yamaha-NS-150-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-NS-150-Service-Manual电路原理图.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、TweeterSubLF Woofer LF Woofer Woofer Terminal Tweeter Terminal C2 C3 L2 L3 L1 C1 YE BL RE BL WH-RE WH BE BL BL-WH BL Woofer Terminal Tweeter Terminal LF Woofer Tweeter4.7F C3 C1 33F C2 6.8F SubLF Woofer L3 0.35mH L1 5.0mH L2 2.2mH 250(9-7/8)19 (3/4) 269(10-5/8) 168(6-5/8) 850(33-1/2) 612(24-1/8) Uni

2、t: mm (inch) P.O.Box 1, Hamamatsu, Japan 100726 SERVICE MANUAL SPEAKER SYSTEM NS-150 NS-150 I DIMENSIONS I WIRING DIAGRAM I NETWORK CIRCUIT DIAGRAM I SPECIFICATIONS Type.3-way bass reflex speaker system (Magnetically-shielded type) Speaker Unit LF Woofer. 13 cm (5) cone SubLF Woofer . 13 cm (5) cone

3、 Tweeter .3 cm (1) dome Frequency Response . 40 Hz 35 kHz Nominal Impedance. 6 ohms Nominal Input Power. 100 W Maximum Input Power . 300 W Sensitivity.89 dB/2.83 V/m Crossover Frequency . 500 Hz, 2 kHz Inpur Terminal .Screw / Banana type Dimensions (W x H x D) . 168 x 850 x 269 mm (6-5/8 x 33-1/2 x

4、10-5/8) Weight. 14.5 kg (32 lbs.) /1 piece Finish . Cherry / Black Accessories .Stand x 4, Screw (6 mm) x 4, Spike x 4, Hex. nut (6 mm) x 4, Wood screw (4 mm) x 4, Pad x 4 Specifications are subject change without notice due to product improvements. RadioFans.CN 收音机爱 好者资料库 1 2 3 4 7 10 11 11 11 15 1

5、6 15 16 1-5 1-24 201 206205 204 202 203 x4 x4 x4 x4x4 x1 1-1-6 1-1-9 1-1-8 1-1-7 1-1-15 NS-150 I EXPLODED VIEW ABCDE 1 2 3 4 5 6 7 Use an Allen wrench (3mm) to unscrew the loud speaker. RadioFans.CN 收音机爱 好者资料库 I PARTS LIST *1V6120000CABINET ASSYCH *1V6120200CABINET ASSYBL *1-1-6V6615600ELECTROLYTIC

6、CAP33uF63V 1-1-7V5370100ELECTROLYTIC CAP6.8uF50V 1-1-8V5357100ELECTROLYTIC CAP4.7uF50V 1-1-9CB818540BINDING TIET-30RF-2 1-1-15EP030200BIND HEAD TAPPING SCREW3x8ZMC2-Y 1-5CB605250HOLDER 1-24CB070450BINDING TIEL=100L=100 2V5383200FRONT GRILLE ASSYCH 2V5383400FRONT GRILLE ASSYBL 3XW232A00 LOUD SPEAKER3

7、cm6 50W 4XY380A00LOUD SPEAKER13cm12 30W *7V6261100SPEAKER TERMINAL 10V5537900OVAL HEAD TAPPING SCREW #13.5x16MFZN2BL 11V5537800HEXAGON SOCKET TAPPING SCREW4x20MFZN2BL 15V5361400TERMINAL CAPS06ERED 16V5361500TERMINAL CAPS06EBLACK ACCESSORIES 201V5004900STAND ASSY1pc/set 202V5386900SPIKEx1 M6x15 203V2

8、450400HEXAGONAL NUTx1 6mmMFZN2-BL *204V6075800LEG ASSY4pcs/set 205EP040250BIND HEAD TAPPING SCREW4x16ZMC2-BL 206EG360010BIND HEAD SCREW6x16MFC2BL * New Parts Ref. No.PART NO.DescriptionRemarksMarkets NS-150 Screw (6 mm) x 4Wood screw (4 mm) x 4 Stand x 4Pad x 4 I ATTACHING THE STAND Procedure: 1. Pu

9、t the 6 mm screw through the larger hole on the stand, and to the speaker at one of the outside holes on the base of the speaker. At this time, attach the stand to the speaker so that it can still be moved slightly. 2. Put the 4 mm wood screw through the smaller hole on the stand, and screw it into

10、the inside hole on the base of the speaker. 3. When both screws have been attached, tighten both of the screws so that the stand is firmly in place. Be sure to check that the stand is firmly attached. 4. Attach the pads to the bottom of the end portion of the stand. 5. Attach the other stands in the

11、 same manner and confirm that all 4 stands have been firmly attached. 6. Place the speaker in the desired location. Note If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. When positioning the speakers, be sure to use the s

12、tand to increase stability. Use the 8 specified holes located on the base of the speaker. I ATTACHING THE SPIKE Procedure: 1. Set the nut close to the tip of the spike and screw them into the bottom of the speaker at each of the four specified holes. 2. Place the speaker in the desired location in a

13、n upright position and adjust the length of the spike to match the depth of the carpet. 3. When adjustment is complete, twist the nut up to the base of the speaker firmly. Notes The tips of the spikes may scratch or otherwise damage the flooring. Please be careful when positioning the speakers. If f

14、orce is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. Either end of the spike may be inserted into the holes on the speaker to accommodate different types of conditions and installations. Spike x 4 When setting up the speakers on a thick carpet, use the spikes instead of the stand. With 4 points set in place to achieve increased stability and improvements in sound quality. NS-150