Yamaha-NXE-200-Service-Manual电路原理图.pdf

《Yamaha-NXE-200-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-NXE-200-Service-Manual电路原理图.pdf（45页珍藏版）》请在收音机爱好者资料库上搜索。

1、RX-E200 RX-E200 SERVICE MANUAL I CONTENTS TO SERVICE PERSONNEL . . . . . . . . . . . . . . . . . . . .1 FRONT PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 REAR PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS . . . . . . . . . . . . . . . . . .

2、. . . . . . . . . .3 INTERNAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 DISASSEMBLY PROCEDURES . . . . . . . . . . . . . . . . .5 TEST MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 AMP ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . .7 TUNER AD

3、JUSTMENTS . . . . . . . . . . . . . . . . . . . 810 IC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1113 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . 1415 PRINTED CIRCUIT BOARD . . . . . . . . . . . . . . . 1624 PIN CONNECTION DIAGRAM . . . . . . . . . . . . . .

4、. . .25 SCHEMATIC DIAGRAM . . . . . . . . . . . . . . . . . . 2628 REMOTE CONTROL TRANSMITTER . . . . . . . . . . . .29 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3038 SYSTEM CONTROL . . . . . . . . . . . . . . . . . . . . . 3948 NX-E200 . . . . . . . . . . . . . . . . . . .

5、. . . . . . . . . . . . . . . .49 This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, an

6、d have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product

7、owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capab

8、ilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, th

9、erefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may

10、have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. IMPORTANT NOTICE 100742 SERVICE MANUAL RX-E200/NX-E200 MINI

11、COMPONENT SYSTEM CRX-E200 CRX-E200 is composed of RX-E200 and CDX-E200. This is a service manual for the RX-E200 (including NX-E200). For service manuals of CDX-E200, please refer to the service manuals with the following publication numbers : CDX-E200100745 RadioFans.CN 收音机爱 好者资料库 RX-E200 RX-E200 I

12、 TO SERVICE PERSONNEL 1. Critical Components Information. Components having special characteristics are marked Z and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only). When service has been completed, it is im

13、perative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. AC LEAKAGE TESTER OR EQUIVALENT EQUIPMENT UNDER TEST INSULATING TABLE WALL OUTLET WARNING: CHEMICAL CONTENT NOTICE! The solder used

14、 in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other r

15、eproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with s

16、older or components located inside the enclosure of this product, wash your hands before handling food. 1 M U, C, R, A models M B, G models I FRONT PANELS GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. RadioFans.CN 收音机爱 好者资料库 RX-E200 RX-E200

17、 2 I REAR PANELS M U model M C model M R model M A model M B model M G model RX-E200 RX-E200 I FM SECTION Tuning Range U, C models . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 107.9MHz A, B, G models . . . . . . . . . . . . . . . . . . . 87.50 to 108.00MHz R model . . . . . . . . . . . . .

18、. 87.5 to 108.0/87.50 to 108.00MHz Usable Sensitivity (75 ) Mono (S/N 30dB) U, C, R models . . . . . . . . . . . . . . . . 1.5V DIN, Mono (S/N 26dB) A, B, G models . . . . . . . . . . . . 1.8V Alternate Channel Selectivity U, C, R models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19、75dB Selectivity (two signals, 40kHz Dev.) A, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55dB Signal-to-Noise Ratio Mono/Stereo (IHF) U, C, R models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77/71dB Mono/Stereo (DIN-weighted, 40kHz Dev.) A, B, G models .

20、. . . . . . . . . . . . . . . . . . . . . . . . . . . 71/65dB Harmonic Distortion Mono/Stereo (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . 0.5/1.0% Frequency Response 20Hz to 15kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 1.5dB Stereo Separation 1kHz . . . . . . . . . . .

21、 . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB I AUDIO SECTION Minimum RMS Output Power per Channel 20Hz to 20kHz, 0.1% THD, 6 U, C, A, B, G models . . . . . . . . . . . . . . . . . . . . 40W + 40W 1kHz, 0.07% THD, 6 . . . . . . . . . . . . . . . . . . . . 50W + 50W Maximum Power per Ch

22、annel (EIAJ) 1kHz, 10% THD, 6 (R model only) . . . . . . . . . 60W + 60W Dynamic Power per Channel (IHF) 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50W + 50W 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65W + 65W 4 . . . . . . . . . . . . .

23、 . . . . . . . . . . . . . . . . . . . . . . . 75W + 75W 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80W + 80W DIN Standard Output Power per Channel 1kHz, 0.7% THD, 4 (G model only) . . . . . . . . . 60W + 60W Dynamic Headroom (6) U, C, models . . . . . . . . . . . . .

24、. . . . . . . . . . . . . . . . . . . . 1.0dB IEC Power 1kHz, 0.04% THD, 6 (G model only) . . . . . . . . 50W + 50W Power Band Width 0.1% THD, 30W/6 . . . . . . . . . . . . . . . . . . . 10Hz to 50kHz Damping Factor 20Hz to 20kHz, 6 . . . . . . . . . . . . . . . . . . . . . . . .60 or more Input Sen

25、sitivity/Impedance CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150mV/47k Maximum Input Signal Level (1kHz, 0.5% THD) CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0V Output Level/Impedance REC OUT . . . . . . . . . . . . . . . . . . .

26、 . . . . . . . . . 150mV/1.2k SUB WOOFER (50Hz) . . . . . . . . . . . . . . . . . . . . . . 2V/730 Headphone Jack Rated Output/Impedance CD, etc 1kHz, 150mV, 6 . . . . . . . . . . . . . . . . . 0.43V/330 Frequency Response (20Hz to 20kHz) CD, etc . . . . . . . . . . . . . . . . . . . . . . . . . . .

27、 . . . . . . . . 00.5dB Total Harmonic Distortion (20Hz to 20kHz) CD, etc to MAIN SP OUT (20W/6) . . . . . . . . . . . . . 0.04% Signal-to-Noise Ratio (IHF-A-Network) CD, etc, Input Shorted (150mV) . . . . . . . . . . . . . . . . . . 93dB Residual Noise (IHF-A-Network) SP OUT . . . . . . . . . . . .

28、 . . . . . . . . . . . . . . . . . . . . . . . . 100V Channel Separation (Vol. 30dB) CD, etc, Input 5.1k Shorted, 1kHz/10kHz . . . . .60dB/45dB Tone Control Characteristics BASS: Boost/cut . . . . . . . . . . . . . . . . . . . . 10dB (50Hz) Turnover Frequency . . . . . . . . . . . . . . . . . 350Hz

29、TREBLE : Boost/cut . . . . . . . . . . . . . . . . . . . 10dB (20kHz) Turnover Frequency . . . . . . . . . . . . . . . . . 3.5kHz Filter Characteristics SUB WOOFER (L.P.F.) . . . . . . . . . . . . . fc = 100Hz, 6dB/oct. I SPECIFICATIONS 3 I AM SECTION Tuning Range U, C models . . . . . . . . . . . .

30、 . . . . . . . . . . . .530 to 1710kHz A, B, G models . . . . . . . . . . . . . . . . . . . . . .531 to 1611kHz R model . . . . . . . . . . . . . . . . 530 to 1710/531 to 1611kHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V/m Signal-to-Noise Ratio . . . . . . . . . .

31、 . . . . . . . . . . . . . . . . . 50dB I TUNER SECTION Tuner Output Level FM (1kHz) 100% mod. U, C, R models . . . . . . . . . . . . . . . . . . . 500mV 40kHz Dev. A, B, G models . . . . . . . . . . . . . . . . . . . 270mV AM (30% mod., 1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . 150mV

32、I GENERAL Power Supply U, C models . . . . . . . . . . . . . . . . . . . . . . . . AC 120V, 60Hz A model . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240V, 50Hz B, G models . . . . . . . . . . . . . . . . . . . . . . . . AC 230V, 50Hz R model . . . . . . . . . . . . . . AC 110/120/220/24

33、0V, 50/60Hz Power Consumption U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110W R, A, B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W Standby Power Consumption U, C models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3W R, A,

34、 B, G models . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4W I SPEAKER SECTION (NX-E200) Type . . . . . . . . . . . . 2way Bass-reflex Magnetic Shielding Type Driver Woofer . . . . . . . . . . . . . . . . . . . . . . 13cm (5-1/8) Cone Type Tweeter . . . . . . . . . . . . . . . . . . . . .

35、 . . 2.5cm (1) Dome Type Frequency Response . . . . . . . . . . . . . . . . . . . . 55Hz to 28kHz Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Nominal Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60W Maximum Input . . . . .

36、. . . . . . . . . . . . . . . . . . . . . . . . . . . . 110W Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87dB/2.83V,1m Crossover Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3kHz Input Terminal . . . . . . . . . . . . . . . . . . . . . . Screw/Banana Ty

37、pe RX-E200 RX-E200 4 * Specifications subject to change without notice. U . USA model C . Canadian model A . Australian model B . British model G . European model R . General model I INTERNAL VIEW qP. C. B. MAIN (6) wP. C. B. MAIN (1) eP. C. B. TUNER rP. C. B. MAIN (2) tP. C. B. OPERATION yPOWER TRA

38、NSFORMER uP. C. B. MAIN (4) iP. C. B. MAIN (3) qrwe iytu G DIMENSIONS Units : mm (inch) 275(10-13/16)22 (7/8) 15 (9/16) 8 (5/16) 312(12-5/16) 217(8-9/16) 100(3-15/16) 108(4-1/4) AC Outlets Switched x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W max Dimensions (W x H x D) RX-E200

39、. . . . . . . . . . . . . . . . . . . . . . . . 217 x 108 x 312mm (8-9/16 x 4-1/4 x 12-5/16) NX-E200 . . . . . . . . . . . . . . . . . . . . . . . . 186 x 300 x 222mm (7-5/16 x 11-13/16 x 8-3/4) Weight RX-E200 . . . . . . . . . . . . . . . . . . . . . . . . 4.5 kg (9 lbs. 14 oz) NX-E200 . . . . . .

40、. . . . . . . . . . . . . . . . . . 4.0 kg (8 lbs. 13 oz) Finish RX-E200 U, C, R, A, B, G models . . . . . . . . . . . . Gold color RX-E200 U, B, G models . . . . . . . . . . . . . . . . . . Silver color NX-E200 . . . . . . . . . . . . . . . . . . . . . High Gloss Piano Finish Accessories . . . . .

41、. . . . . . . . . . . . . . . . . AM loop antenna x 1 Indoor FM antenna x 1 Remote Control Transmitter x 1 Battery (size UM-4E, R03) x 4 Speaker Cord (4m) x 2 RX-E200 RX-E200 Fig. 1 q q Top Cover Fan w w e r t Fig. 2 Amp Unit y Fig. 3 I DISASSEMBLY PROCEDURES (Remove parts in disassembly order as nu

42、mbered.) 1. Removal of Top Cover a. Remove 4 screws ( q ) and 4 screws ( w ) in Fig. 1. 5 y 2. Checking the Amp Unit and replacing parts a. Disconnect the power plug from AC outlet. b. Remove 2 screws ( e ) attaching the rear panel to the chassis. (Fig. 2) c. Disconnect the connector for the fan. d.

43、 Remove 3 screws ( r, t ) attaching the fan to the chassis and then remove the fan. (Fig. 2) e. Remove 3 screws ( y ) attaching the Main P.C.B. to the Heat Sink. (Fig. 2) f. Loosen the wiring harness. g. Move the Amp Unit toward the rear. (Fig. 2) h. As shown in Fig. 3, set the Amp Unit upright. i.

44、Fit insulating material (thick paper, etc.)to prevent the chassis and the transformer from contacting the Main P.C.B. j. Using a wire, connect the pin jack ground to the chassis. (If they are left unconnected, the grounding remains open and the unit fails.) k. Connect the power plug and turn on the

45、power switch. l. When replacing parts, remove 5 screws ( u, i ) fixing the P.C.B. Tuner and then remove the P.C.B. Tuner. (Fig. 3) u i (Copper) (Copper) (Copper) RX-E200 RX-E200 6 ITEST MODE STANDBY/ON Key is pushed while pushing DISPLAY Key and AUTO/MANL Key. TEST MODE indication. PRESET/TUNING B K

46、ey Test mode number up. PRESET/TUNING N Key Test mode number down. PRESET/BAND Key Executive test mode. STANDBY/ON Key POWER OFF The completion of test mode. POWER Off condition TEST MODE UPTEST MODE DOWN When present mode is carried out. Test mode is finished. DISPLAYFUNCTIONPRESET/BAND Key 01 DEST

47、-B,G 02 FL+CLEAR Stop/Low/High DESTINATIONR (AM9k/FM:50k)R (AM10k/FM100k)AB,GU,CJ DisplayR9kR10kAB, GU, CJ (*1) 03 FL CHECK 04 FANStop 05 Ver-Z1.02 06 SUM5b4d 0599.05.28 TEST PROGRAM MODE FUNCTION DESCRIPTION Indication for destinaion. (*1) All FL segments and BACKUP RAM CLEAR. All FL segments and c

48、ircuit board short circuit inspection. Cooling fan drive OUT Version information of the microcomputer software. (*2) The date of the microcomputer software. (*2) The calculation of SUM is done and indicated after that. (*2) 1st : all segments light 2nd : RAM CLEAR 1st : all segments light 2nd : Even

49、-numbered segments and even numbered digits are turned on. 3rd : Odd -numbered segments and odd- numbered digits are turned on. It is changed to the date indication. It is changed to version indication. Re-calculation (*2) Contents of indication change by the microcomputer software. (Note that memories set by the user will be erased.) Also, the preset contents of the tuner are restored to the factory preset ones. PRESET EDIT VOLUMERDS PSPTY RT CT PTY HOLD STEREOAUTOTIMER SLEEPTUNEDMEMORY TIMER STANDBY EDIT VOLUMERDSPTYC