Yamaha-RXV-3200-Service-Manual电路原理图.pdf

《Yamaha-RXV-3200-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-RXV-3200-Service-Manual电路原理图.pdf（92页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL AV RECEIVER/AV AMPLIFIER RX-V3200/DSP-AX3200 100780 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products,

2、 are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified

3、. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certificatio

4、n or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving

5、 to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive component

6、s. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. P.O.Box 1,

7、 Hamamatsu, Japan I CONTENTS TO SERVICE PERSONNEL . 1 IMPEDANCE SELECTOR . 1 FRONT PANELS. 2 REAR PANELS . 24 REMOTE CONTROL TRANSMITTER . 4 SPECIFICATIONS. 57 INTERNAL VIEW . 8 DISASSEMBLY PROCEDURES . 911 SELF DIAGNOSIS FUNCTION (DIAG) . 1233 AMP CHECK . 34 DISPLAY DATA . 3536 IC DATA . 3743 BLOCK

8、 DIAGRAM. 4447 PRINTED CIRCUIT BOARD . 4875 PIN CONNECTION DIAGRAM . 7677 SCHEMATIC DIAGRAM . 7883 PARTS LIST. 84105 REMOTE CONTROL TRANSMITTER . 106107 RX-V3200/DSP-AX3200 RX-V3200/DSP-AX3200 RX-V3200/DSP-AX3200 435 (17-1/8) Unit : mm (inch) 191 (7-1/2) 170 (6-11/16)429 (16-7/8) 21 (13/16) 16 (5/8)

9、 23 (15/16) 468 (18-7/16) 1 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may a

10、lso contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA- SON WHATSOEVER! Avoid prolonged

11、, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. I TO SERVICE PERSONNEL 1. Critical

12、Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed

13、conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. I IMPEDANCE SELECTOR IMPEDANCE SELECTOR WARNING: Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be dam

14、aged. DIMENSIONS “CAUTION” “F311: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 250V FUSE.” “F312: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V FUSE.” CAUTION F311: REPLACE WITH SAME TYPE 10A, 250V FUSE. F312: REPLACE WITH SAME

15、 TYPE 5A, 125V FUSE. ATTENTION F311: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 250V. F312: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V. GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. RX-V3200/DSP-AX3200 RX-V3200/DSP-A

16、X3200 I FRONT PANELS RX-V3200 (U, C, A, R, T models) DSP-AX3200 (B, G models) 2 I REAR PANELS RX-V3200 (U, C models) RX-V3200/DSP-AX3200 RX-V3200/DSP-AX3200 RX-V3200 (A model) RX-V3200 (R, T models) 3 DSP-AX3200 (B model) RX-V3200/DSP-AX3200 RX-V3200/DSP-AX3200 4 DSP-AX3200 (G model) I REMOTE CONTRO

17、L TRANSMITTER RX-V3200/DSP-AX3200 RX-V3200/DSP-AX3200 5 I SPECIFICATIONS I Audio Section Minimum RMS Output Power (Power Amp. Section) (20 Hz to 20 kHz, 0.02% THD, 8 ohms) MAIN L/R.120W + 120W CENTER. 120W REAR L/R/C . 120W + 120W + 120W Maximum Power (EIAJ) R, T models (1 kHz, 10% THD, 8 ohms) MAIN

18、 L/R.165W + 165W CENTER. 165W REAR L/R/C . 165W + 165W + 165W Dynamic Power Per Channel (IHF) MAIN L/R (8/6/4/2 ohms) . 145/180/240/330W DIN Standard Output Power Per Channel B, G models (1 kHz, 0.7% THD, 4 ohms) MAIN L/R.180W + 180W CENTER. 180W REAR L/R/C . 180W + 180W + 180W Dynamic Headroom U, C

19、, R, T models (8 ohms) . 0.82 dB IEC Power B, G models MAIN L/R (1 kHz, 0.02% THD, 8 ohms).120W + 120W Power Band Width MAIN L/R (0.08% THD, 60W/8 ohms).10 Hz to 50 kHz Damping Factor MAIN L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) . 200 or more Input Sensitivity / Input Impedance PHONO (MM). 2.5 mV /

20、 47 k-ohms CD, etc. . 150 mV / 47 k-ohms EXT. DECODER MAIN L/R. 150 mV / 47 k-ohms CENTER, SURROUND L/R, SUBWOOFER .150 mV / 40 k-ohms MAIN IN. 1V / 47 k-ohms Maximum Input Signal Level PHONO (MM) (1 kHz, 0.1% THD). 100 mV CD, etc. (1 kHz, 0.5% THD, EFFECT ON). 2.2 V Output Level / Output Impedance

21、REC OUT . 150 mV / 0.9 k-ohms PRE OUT (MAIN L/R, CENTER, REAR L/R/C). 1.0 V / 1.2 k-ohms PRE OUT (SUB WOOFER, EFFECT OFF, MAIN Small) . 4.0 V/1.2 k-ohms ZONE2 OUT U, C, A, R, T models . 150 mV / 1.2 k-ohms Headphone Jack Rated Output / Impedance 1 kHz, 40 mV, 8 ohms . 150 mV / 100 ohms Frequency Res

22、ponse CD, etc. to MAIN L/R (10 Hz to 100 kHz) . 0/-3 dB MAIN IN to MAIN L/R (5 Hz to 100 kHz) . 0/-3 dB RIAA Equalization Deviation PHONO (MM) (20 Hz to 20 kHz) . 00.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) PHONO (MM) to REC OUT (1V) .0.02% or less CD, etc. (EFFECT OFF) to PRE OUT MAIN L/R (

23、1V) .0.02% or less CD, etc. (EFFECT OFF) to SP OUT MAIN L/R (60W /8 ohms) .0.02% or less MAIN IN to SP OUT MAIN L/R (60W /8 ohms) .0.008% or less Signal to Noise Ratio (IHF-A network) (Input shorted) PHONO (MM) to SP OUT (5 mV) U, C, R, T models .86 dB or more A, B, G models.81 dB or more CD, etc. (

24、EFFECT OFF) to SP OUT 150 mV .96 dB or more 250 mV .100 dB or more Residual Noise (IHF-A netwok) MAIN L/R SP OUT . 150 V or less Channnel Separation (EFFECT OFF) PHONO (Input shorted, 1 kHz/10 kHz) . 60 dB or more/55 dB or more CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) . 60 dB or more/45 dB

25、or more Tone Control Characteristics Bass:Boost/Cut . 10 dB (50 Hz) Turnover Frequency . 350 Hz Treble: Boost/Cut . 10 dB (20 kHz) Turnover Frequency . 3.5 kHz Filter Characteristics MAIN L/R, CENTER, Rear L/R/C Small (H.P.F.) . 90 Hz, 12 dB/oct. SUBWOOFER (L.P.F.) . 90 Hz, 18 dB/oct. Bass Extension

26、 MAIN L/R, 60 Hz . +6 dB I Video Section Video Signal Type U, C models . NTSC R, T models.NTSC or PAL A, B, G models. PAL Video Signal Level . 1 Vp-p / 75 ohms S-Video Signal Level Y . 1 Vp-p / 75 ohms C .0.286 Vp-p / 75 ohms Component Signal Level Y . 1 Vp-p / 75 ohms Cb/Cr . 0.7 Vp-p / 75 ohms Max

27、imum Input Level . 1.5 Vp-p Signal to Noise Ratio .50 dB or more Monitor Out Frequency Response Component Video Signal, S-Video Signal . 5 Hz to 10 MHz, -3 dB Component Video Signal . DC to 60 MHz, -3 dB I FM Section Tuning Range U, C models . 87.5 to 107.9 MHz A model .87.50 to 108.00 MHz R, T mode

28、ls. 87.5 to 108.0 / 87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) U, C, A, R, T models (100% Mod) Mono . 2.0 V (17.3 dBf) Stereo . 25 V (39.2 dBf) Usable Sensitivity (IHF) U, C, A, R, T models Mono . 1.0 V (11.2 dBf) Selectivity U, C, A, R, T models at 400 kHz . 70 dB Signal to Noise Ratio (I

29、HF) U, C, A, R, T models Mono / Stereo .76 dB / 70 dB Harmonic Distortion U, C, A, R, T models (1 kHz) Mono/Stereo. 0.2 / 0.3 % Stereo Separation U, C, A, R, T models 1 kHz . 45 dB Frequency Response U, C, A, R, T models 20 Hz to 15 kHz .+0.5 / -2 dB Antenna Input U, C, A, R, T models . 75 ohms unba

30、lanced I AM Section Tuning Range U, C models . 530 to 1,710 kHz A model . 531 to 1,611 kHz R, T models. 530 to 1,710 / 531 to 1,611 kHz Usable Sensitivity U, C, A, R, T models . 300 V/m Antenna U, C, A, R, T models . Loop Antenna I General Power Supply U, C models .AC 120 V, 60 Hz A model .AC 240 V,

31、 50 Hz B, G models .AC 230 V, 50 Hz R model . AC 110/120/220/240 V, 50/60 Hz T model .AC 220 V, 50 Hz Power Consumption U. C models . 500 W / 640 VA A, B, G, R, T models . 500 W Standby Power Consumption (reference data) U, C, A, B, G models . 1.2 W R, T models AC 220V, 50Hz . 1.5 W Maximum Power Co

32、nsumption R model 6 ch Drive, 10% THD . 1000 W AC Outlets 3 switched outlets U, C models . 100W max., total B, G models . 100W max., total R, T models. 50W max., total 1 switched outlet A model . 100W max. Dimensions (W x H x D) . 435 x 191 x 468 mm (17-1/8 x 7-1/2 x 18-7/16) Weight . 21.0 kg (46 lbs. 5 oz.) Finish RX-V3200.Gold color (U, C, R, T) models Black color (U, C, R, A) models DSP-AX3200 .Black color (B, G) models T