Yamaha-SREV-1-Service-Manual电路原理图.pdf

《Yamaha-SREV-1-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-SREV-1-Service-Manual电路原理图.pdf（92页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL PA 1/2 011555 HAMAMATSU, JAPAN 1.415K-0671 Printed in Japan 01.02 CONTENTS SPECIFICATIONS 3 PANEL LAYOUT 4 CIRCUIT BOARD LAYOUT 5 DIMENSIONS 6 WIRING 7 BLOCK DIAGRAM 9 DISASSEMBLY PROCEDURE 11 I/O CARD INSTALLATION 16 DB-SREV1 INSTALLATION 17 LSI PIN DESCRIPTION 19 IC BLOCK DIAGRAM 24

2、 CIRCUIT BOARDS 29 TEST PROGRAM 41 ERROR MESSAGES 44 MIDI IMPLEMENTATION CHART 46 PARTS LIST RC-SREV1 SERVICE MANUAL SREV1/RC-SREV1 OVERALL CIRCUIT DIAGRAM SREV1:20001225-500000 RC-SREV1:20001225-150000 DB-SREV1:20001225-200000 This document is printed on chlorine free (ECF) paper with soy ink. SAMP

3、LING REVERBERATOR/ DSP EXPANSION BOARD/REMOTE CONTROLLER DB-SREV1SREV1 SREV1 2 WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals

4、 found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between s

5、older and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. IMPORTANT NOTICE This manual has been provided for the use of auth

6、orized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service a

7、nd safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retaile

8、r or the appointed service representative. IMPORTANT:This presentation or sale of this manual to any individual or firm does not constitute authorization, certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form. The data provided i

9、s belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice o

10、r obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy g

11、auge black wires connect to this bus). IMPORTANT:Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originall

12、y installed. LITHIUM BATTERY HANDLING This product uses a lithium battery for memory back-up. WARNING:Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following precautions when handling or replacing lithium batteries. Leave lithium battery replacement t

13、o qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the batter

14、y polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disassemble the batteries. Never heat batteries or throw them into fire. ADVARSEL! Lithiumbatteri-Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat

15、og type. Levr det brugte batteri tilbage til leverandren. VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi rjht, jos se on virheellise

16、sti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti. The following information complies with Dutch Official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES. Please refer to the diassembly procedu

17、re for the removal of Back-up Battery. Leest u voor het verwijderen van de backup batterij deze beschrijving. SPECIFICATIONS SREV1 3 IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT.The wires in this main lead are coloured in accordance with the following code: BLUE:NEU

18、TRAL BROWN: LIVE As the colours of the wires in the main lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The BLUE wire must be connected to the terminal that is marked with the letter N (or coloured BLACK). The BROWN wi

19、re must be connected to the terminal that is marked with the letter L (or coloured RED). Be certain that neither core is connected to the earth terminal of the three pin plug. Sampling rate Internal External Internal processing Program Memories 2-channel, 4-channel mode 2-channel x2 mode Indicators

20、INPUT OUTPUT FS LOCK Others PC Card slot CD-ROM drive Cooling fan Power requirements Power consumption Dimensions (W x H x D) Weight Free-air operating temperature Power cord length Supplied accessories Options 48 kHz 44.1 kHz or 48 kHz 32 bit 6 (P01P06) 12 (P01P12) SIGNAL x4 (34 dB), CLIP x4 SIGNAL

21、 x4 (34 dB), CLIP x4 48K, 44.1K POWER, PC Card, CD-ROM PCMCIA (Type II), PC Card ATA spec, FAT16 ISO9660 Level 2 format x2 U.S.A. remove the back-up battery. DIGITAL(AES/EBU) to SUB 4/4-CN802 to Power supply unit-CN6 to CNV-CN3to CNV-CN2 -CN3-CN3 SREV1 34 Lithium Battery CD-ROM Circuit Board Compone

22、nt side Component side CPU, CD-ROM: 3NA-V587910-22 D D CPU, CD-ROM: 3NA-V587910-31 CPU Circuit Board CD-ROM Circuit Board Pattern side SREV1 35 D D Pattern side 3NA-V587910-31 SREV1 36 to CPU-CN113 to CPU-CN114 MEMORY CARD SREV1 37 PCM Circuit Board Component side Pattern side 3NA-V587910-2 3NA-V587

23、910-3 1 1 SREV1 38 to SUB 2/4-CN604to CPU-CN301to Power supply unit-CN2 to Power transformer to Power transformerto Power transformer SUB 1/4 Circuit Board 3NA-V5879202 Component side Pattern side SREV1 39 to Power supply unit-CN7to SUB 1/4-CN705 SLOT1 SLOT2 to CPU-CN120to CPU-CN121 SUB 2/4 Circuit

24、Board 3NA-V5879202 Component side Pattern side SREV1 40 to CPU-CN117 INPUT SIGNAL CH1 INPUT SIGNAL CH2 INPUT SIGNAL CH3 INPUT SIGNAL CH4 OUTPUT SIGNAL CH1 OUTPUT SIGNAL CH2 OUTPUT SIGNAL CH3 OUTPUT SIGNAL CH4 FS LOCK 44.1K INPUT CLIP CH1 INPUT CLIP CH2 INPUT CLIP CH3 INPUT CLIP CH4 OUTPUT CLIP CH1 O

25、UTPUT CLIP CH2 OUTPUT CLIP CH3 OUTPUT CLIP CH4 FS LOCK 48K Power supply unit-CN1 to AC inlet, to CPU-CN124 POWER ON/OFF SUB 3/4 Circuit Board SUB 4/4 Circuit Board SUB 3/4, SUB 4/4: 3NA-V5879202 Component side Pattern side Pattern sideComponent side UPGRADE AND TEST PROGRAM 1.Outline of test program

26、 The test program is a separate and individual application from the regular program. (Not provided with this program) The test program is provided in a file titled “diag.bin”. The test program is used by connecting the SERIAL-1 terminal of the SREV1 and the RS232C terminal on an IBM-compatible PC us

27、ing a DSUB9p-miniDIN8p cable. The terminal software “TeraTerm” is required when using on an IBM- compatible PC. “TeraTerm” can be downloaded from the URL shown below. http:/www.vector.co.jp/authors/VA002416/teraterm.html (The address may be changed in future.) 2.Preparations for inspection *1 Use an

28、 IBM-compatible PC that has a COM port. The settings for the COM port are: 8bit, Non-Parity, 1 Stop bit, No Flow Control. *2 Refer to the items relating to the details of individual inspections (MY8) for information about the loop back of the MY8 card. *3 This the CD-ROM disc included in the package

29、 with the product. *4 Store the test program “diag.bin” in the PC ATA card for the inspection. Dowload “diag.bin” from the YSISS home page. 3.Starting the test program Turn on the power and after the normal application has started, start the test program using the PC card with the test program in it

30、. Once the test program has been started, the following will appear on the “TeraTerm” terminal software. 4.Operating the test program The various tests in the test program are started by entering them in the command line of the “TeraTerm” terminal software. As a result, the following will appear on

31、the “TeraTerm” terminal software. 5.Test items 5-1. serv, total check The inspection of the overall assembly is started by entering “serv” from the terminal. This will start the inspection and the progress status of the inspection for each item will be displayed on the terminal. The inspection is co

32、mpleted. If all the items are OK, the following is displayed. If there were items that were NG, the following list will be displayed. 5-2. Individual checks Inspections of the following items are performed. CD-ROM DiskPC ATA Card AES/EBU IN 1 AES/EBU IN 2 AES/EBU OUT 1 AES/EBU OUT 2 MIDI OUT MIDI IN

33、 SERIAL 2 SERIAL 1 REMOTE WORDCLOCK IN 5 6 10 SLOT 1 SLOT 2 1 11 9 MEMORY CARDCD-ROM 8 IBM-compatible PC Cable VZ729000 MY8 Card -AT -AE -TD Optical cable No. 1 5 6 89 10 11 Items Use a DSUB9p-miniDIN8p Cable to connect the SERIAL- 1 terminal and the RS232C terminal on the PC (*1) Use a canon cable

34、to connect AES/EBU IN-1 and AES/EBU OUT-1 Use a canon cable to connect AES/EBU IN-2 and AES/EBU OUT-2 If there is a MY8 card in the option slot, loop back (*2). Insert the CD-ROM Disc (*3) provided in the SREV1 package into the CD-ROM drive. Insert the PC ATA Card (*4) into the MEMORY CARD slot. SRE

35、V1 Diagnostics version 0.7 Copyright(C) 2000 YAMAHA Corporation All rights reserved. wait for ready: 0 exec_device_diagnostic: 14 soft_reset 0: soft_reset 1: device not ready CF=Slave, CD-ROM=Master diag Results of Service Tests - Test of AES/EBU-1 - DIR5-1 Lock.NG X DIT2-1 - DIR5-1 Subcode.NG XXXX.

36、 XXXX. XXXX. XXXX. XXXX. XXXX. XXXX. XXXX DIT2-1 - DIR5-1 Signal.NG XXXX. XXXX. XXXX. XXXX. XXXX - Test of MY Slot-2 - Card Detect. OK MY8-AE Status (Lock/Hold). NG XXXX Audio Line. NG XXXX. XXXX diag diag serv Service Tests are All OK diag 1 2 3 4 5 6 7 System LEDs Drive DSP6 CNV AES my8 Checks the

37、 SDRAM, SRAM, Battery Tests that LEDs come on. Visually confirm that the LEDs come on in the predetermined sequence. Checks the internal Card, CD-ROM Drive, PCMCIA Slot Checks the DSP6 and DRAM. Checks access to the CNV circuit board. Checks AES/EBU IN/OUT Checks the miniYGDAI slot. Must be confirme

38、d visually. Automatically determines the number of CNV circuit boards. Makes two checks if there is a DB-SREV1 Insert two MY cards. Automatically determines the type of the MY cards. NotesDescription Individual commands No. SREV1 41 5-2-1. sys In the FlashROM and SDRAM program section, operation is

39、normal if the test program starts. Checks the SDRAM coefficient buffer range, backup RAM (SRAM) and battery. 5-2-2. led The LEDs will come on in the sequence shown below. Visually check that they come on as indicated. 5-2-3. drive Checks the internal Card, CD-ROM Drive, PCMCIA Slot Insert the CD-ROM

40、 disk included in the package for the product in the CD- ROM drive. Insert the PC ATA card for inspection into the PCMCIA slot. A: Internal CF Card, B: If both of the CD-ROM drives are NG, remove the FPC cable for CN109 and CN110. and reinspect the internal CF card. 5-2-4. dsp6 Checks the DSP6 and D

41、RAM. If all the items are NG, check the system clock (60 MHz).: X104 If all of the DRAM items are NG, check 128Fs, Sync.: IC165 5-2-5. cnv Checks the CNV circuit boards. Since DSP6 is used for inspecting Data1and Coef, make sure that the DSP6 has passed its test before proceeding. 5-2-6. aes Checks

42、AES/EBU IN/OUT 5-2-7. my8 Checks the miniYGDAI slot. Automatically identifies the MY cards in the slot. If the cards are MY-8AE, MY8-AT, MY8-TD, the following checks are performed. Only card identification is performed for all other cards. There is a need to loop back MY-8AE, MY8-AT, MY8-TD cards. I

43、NPUT1/2 Hot - OUTPUT1/2 Hot INPUT1/2 Cold - OUTPUT1/2 Cold INPUT3/4 Hot - OUTPUT3/4 Hot INPUT3/4 Cold - OUTPUT3/4 Cold INPUT5/6 Hot - OUTPUT5/6 Hot INPUT5/6 Cold - OUTPUT5/6 Cold INPUT7/8 Hot - OUTPUT7/8 Hot INPUT7/8 Cold - OUTPUT7/8 Cold 1 - 5 14 - 18 2 - 6 15 - 19 3 - 7 16 - 20 4 - 8 17 - 21 10, 1

44、2, 13, 21, 22, 23, 24, 25 GND 9, 11 OPEN MY8-AE 131 14 25 Inspection items SDRAM (Data Bus) SDRAM (Addr Bus) Backup RAM (Data Bus) Backup RAM (Addr Bus) Battery Check these areas if NG SDRAM (IC111, IC112), IC110 SDRAM (IC111, IC112), IC110 SRAM (IC108, IC109) SRAM (IC108, IC109) BT101, IC103 Inspec

45、tion items All LEDs Each LED All LEDs Blink Notes All LEDs come on for 1 second. The LEDs come on one at a time in 0.3 second intervals. The sequence for the LEDs to come on is shown in the figure below. Two cycles are performed. All LEDs blink for 3 seconds. Inspection items A: Internal CF Card B:

46、CD-ROM Drive C: PCMCIA Slot Check these areas if NG CF101, IC113, IC117, IC123, IC137, IC138 CD-ROM circuit board, CD-ROM Drive, CN109, CN110, IC113, IC117, IC123, IC137, IC138 PCMM circuit board, IC117, IC121, IC127, IC128, IC129, IC130, IC132, IC135, IC136, IC139 Inspection items CPU Interface (Da

47、ta Bus) CPU Interface (Data Bus) CPU Interface (CS, TXB) CPU Interface (Addr Bus) Check these areas if NG oX IC159 Xo IC143 XX IC113, IC177, IC178, IC143, IC159 oX IC159 Xo IC143 XX IC113, IC169 oX IC159 Xo IC143 XX IC113, IC179 oX IC159 Xo IC143 XX IC113, IC179 Inspection items CPU Interface (BWR/B

48、RR) DRAM Interface (Data Bus) DRAM Interface (Addr Bus) DRAM Interface (MPR) PIO Connection Check these areas if NG oX IC159 Xo IC143 XX IC153, IC154, IC159 oX IC153, IC154, IC159 Xo IC140, IC141, IC143 oX IC153, IC154, IC159 Xo IC140, IC141, IC143 oX IC159 Xo IC143 IC159, IC143 Inspection items CPU

49、 Interface (Data Bus) CPU Interface (Addr Bus) CPU Interface (IRQ) Data1 (Pulse - Rand) Coef2 (Linear DIR5-1 Subcode DIT2-1 - DIR5-1 Signal DIR5-2 Micon Interface DIR5-1 Lock DIT2-2 - DIR5-2 Subcode DIT2-2 - DIR5-2 Signal Check these areas if NG IC113, IC145, IC146, IC150, IC156, IC157, IC158,IC162 IC142, IC150 IC113, IC142, IC148, IC157, IC158, IC162 IC142, IC148 IC113, IC145, IC146, IC151, IC156, IC157, IC158, IC162 IC142, IC151 IC113, IC142, IC149, IC157, IC158, IC162 IC142, IC149 Inspection items Card Detect Status (Lock/Hold) Audio Line