NAD-T163-pre-tb3维修电路原理图.pdf

《NAD-T163-pre-tb3维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《NAD-T163-pre-tb3维修电路原理图.pdf（5页珍藏版）》请在收音机爱好者资料库上搜索。

1、PAGE 1 OF 5 Technical BulletinT163 Product: A/V Tuner Preamplifier Hardware Technical Bulletin: T163-H2004-03 Date:August 24/04Subject:Residual Noise Note:Implemented in production from Serial number :R47T1630186 Previous T.B.s required: Please refer to the following software bulletin to perform the

2、 software upgrade procedure. K K K K YEST163-S2004-01 Software Upgrade Procedure K K K K NO DESCRIPTION: At high volume setting with no signal on an unterminated analogue input, there maybe some audiable residual hum noise and whistling sound coming form one or more channels. REASON:The residual noi

3、se is coming from power supply ground and DSP ground. The whistle noise is coming from the DSP board. SOLUTION: Remove the DSP board and order the replacement DSP board from our spares department . This board will require version 2.03 software or later,check for current version on our service websit

4、e, . Also see above for software bulletin for the software upgrade procedure. Order the part number for the DSP board using this number, 80-0907630-65-00 from our spares department. This board has Dolby Pro LogicIIx installed. NOTE: The HDCD decoder is replaced by the Dolby PLIIx decoder. Ground Cha

5、nges 1. Change the cable between J617 on Pre-out board and Multi-channel RCA from AWG22 to AWG18. Figure1 Contact: NAD Electronics International 633 Granite Court Pickering, ON Canada L1K 3K1 Voice: 905-831-0799 FAX 905-837-6357 Note: If this is not present on the unit, add an AWG18 wire between the

6、 Pre-out RCA and Multi-channel RCA jacks as shown. RadioFans.CN 收音机爱 好者资料库 PAGE 2 OF 5 Technical BulletinT163 Product: A/V Tuner Preamplifier Hardware Technical Bulletin: T163-H2004-03 Ground Changes 2. The jumper wire between G2A on MAIN board and G2B on AUDIO IN board , remove the end connected to

7、 G2B on the AUDIO IN board and connect this end to the chassis GROUND LUG. See figure2. Figure 2 3. For J705B and J704B on AUDIO PCB , cut all the AGND pins. That is pins 4,5,7 and 9 .on both J704B and J705B. See arrows in figure 3. NOTE: We suggest using the following slim line side cutters to allo

8、w for easy cutting of pins.Consult your local supplier. See Figure 3A. Figure 3 Figure 3A RadioFans.CN 收音机爱 好者资料库 PAGE 3 OF 5 Technical BulletinT163 Product: A/V Tuner Preamplifier Hardware Technical Bulletin: T163-H2004-03 Ground Changes 4. Add a jumper wire between J8(copper bar) on main board and

9、 chassis. See figure 4. Figure 4 5. Install an AWG18 wire from the DSP board to the MULTI-CH. RCA connector ground. See Figure 5 Figure 5 RadioFans.CN 收音机爱 好者资料库 PAGE 4 OF 5 Technical BulletinT163 Product: A/V Tuner Preamplifier Hardware Technical Bulletin: T163-H2004-03 DSP changes 2. When installi

10、ng the new DSP board perform the following. Float the DSP AGND (including the grounding bracket or remove it) from the chassis using an insulated washer. See figure 6 ,7 and 8. Figure 6 New DSP board (indicated by yellow dot) Figure 7 Contact: NAD Electronics International 633 Granite Court Pickerin

11、g, ON Canada L1K 3K1 Voice: 905-831-0799 FAX 905-837-6357 RadioFans.CN 收音机爱 好者资料库 PAGE 5 OF 5 Technical BulletinT163 Product: A/V Tuner Preamplifier Hardware Technical Bulletin: T163-H2004-03 3. Mount the front panel ground cable to the nearest front panel screw as shown in figure 8. Figure 8 Contact: NAD Electronics International 633 Granite Court Pickering, ON Canada L1K 3K1 Voice: 905-831-0799 FAX 905-837-6357 RadioFans.CN 收音机爱 好者资料库