Sony-STRDA5700ES-rec-sm 电路图 维修手册.pdf

《Sony-STRDA5700ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA5700ES-rec-sm 电路图 维修手册.pdf（262页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Published by Sony Techno Create Corporation STR-DA5700ES SPECIFICATIONS MULTI CHANNEL AV RECEIVER 9-893-354-03 2012E33-1 2012.05 US Model Canadian Model AEP Model UK Model Ver. 1.2 2012.05 Note: Be sure to keep your PC used for service and checking of this unit always

2、 updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, contact your Service Headquarters. (US and Canadian models only) AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 2

3、0 20,000 Hz; rated 130 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section (US and Canadian models) POWER OUTPUT1) 2) Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0.09%): 130 W + 130 W Reference

4、Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 130 W + 130 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT: 140 W + 140 W CENTER: 140 W SURROUND: 140 W + 140 W SURROUND BACK: 140 W + 140 W Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT: 130 W + 130 W CENTER: 130 W SURRO

5、UND: 130 W + 130 W SURROUND BACK: 130 W + 130 W 1) Measured under the following conditions: Power requirements: 120 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be no sound output. Frequency response3) 3) When “2ch Analog Direct” is being used. Inputs (Analog) Input

6、s (Digital) Outputs FM tuner section Tuning range87.5 108.0 MHz Antenna (aerial)FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced AM tuner section (US and Canadian models) Intermediate frequency 450 kHz Antenna (aerial)Loop antenna (aerial) Video section Inputs/Outputs Video:1

7、Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB: 0.7 Vp-p, 75 ohms PR: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through HDMI Video Input/Output (HDMI Repeater block) 640 480p 59.94/60 Hz 720 480p 59.94/60 Hz 1280 720p 59.94/60 Hz 1920 1080i 59.94/60 Hz 1920 1080p 59.94/60 Hz 720 576p 50 Hz 1280 720p 50

8、 Hz 1920 1080i 50 Hz 1920 1080p 50 Hz 1280 720p 29.97/30 Hz 1920 1080p 29.97/30 Hz 1280 720p 23.98/24 Hz 1920 1080p 23.98/24 Hz HDMI Video (3D) Input/Output (HDMI Repeater block) 1280 720p 59.94/60 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080i 59.94/60 Hz Frame Packing

9、Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p 59.94/60 Hz Side-by-Side (Half) Over-Under (Top-and-Bottom) PHONORIAA equalization curve 1.0 dB (20 Hz 20 kHz) MULTI CHANNEL INPUT, SA-CD/CD, TAPE, MD, TV, VIDEO 1/2, BD/DVD, SAT/CATV, GAME 10 Hz 100 kHz 3 dB PHONOSensitivity: 2.5 mV Impedan

10、ce: 50 kohms S/N: 90 dB (A, 20 kHz LPF) MULTI CHANNEL INPUT, SA-CD/CD, TAPE, MD, TV, VIDEO 1/2, BD/DVD, SAT/CATV, GAME Sensitivity: 150 mV Impedance: 50 kohms S/N: 100 dB (A, 20 kHz LPF) IN 1 (BD/DVD), IN 2 (VIDEO 1), IN 3 (SA- CD/CD) (Coaxial) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz LPF) IN 1 (GAM

11、E), IN 2 (SAT/CATV), IN 3 (TV), IN 4 (MD) (Optical) S/N: 96 dB (A, 20 kHz LPF) TAPE (REC OUT), VIDEO 1, ZONE 2, ZONE 3 (AUDIO OUT) Voltage:150 mV Impedance: 1 kohm FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, FRONT HIGH L/R, SUBWOOFER Voltage: 2 V Impedance: 1 kohm Tuning scaleTuning range 10

12、 kHz step530 1,710 kHz 9 kHz step531 1,710 kHz 1280 720p 50 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080i 50 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p 50 Hz Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p 23.98/24 Hz Frame Pa

13、cking Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p 29.97/30 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1280 720p 23.98/24 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1280 720p 29.97/30 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-B

14、ottom) Playable types of files Type of content File formatExtensions VideoMPEG-1 Video/ PS1) 2) MPEG-2 Video/ PS, TS1) 3) “.mpg,” “.mpeg,” “.m2ts,” “.mts” MPEG-4 AVC1) 2) “.mkv,” “.mp4,” “.m4v,” “.m2ts,” “.mts” WMV91) 2) “.wmv,” “.asf” AVCHD2) 4) Xvid“.avi” 1) The receiver does not play coded files

15、such as DRM. 2) The receiver does not play this file format on a DLNA server. 3) The receiver can only play standard definition video on a DLNA server. 4) The receiver plays AVCHD format files that are recorded on a digital video camera, etc. The AVCHD format disc will not play if it has not been co

16、rrectly finalised. 5) The receiver does not play coded files such as Lossless. 6) Sampling frequency/bit depth supported: up to 192 kHz/24 bit Notes ?Some files may not play depending on the file format, file encoding, recording condition, or DLNA server condition. ?Some files edited on a computer m

17、ay not play. ?The receiver can recognise the following files or folders in USB devices: up to folders in the 3rd tree up to 500 files in a single tree ?The receiver can recognise the following files or folders stored in the DLNA server: up to folders in the 18th tree up to 999 files in a single tree

18、 ?Some USB devices may not work with this receiver. ?The receiver can recognise Mass Storage Class (MSC) devices (such as flash memory or an HDD), Still Image Capture Device (SICD) class devices and 101 keyboard (front USB jack only). MusicMP3 (MPEG-1 Audio Layer III)6) “.mp3” AAC1) 2) 5) 6)“.m4a” W

19、MA9 Standard1) 2) 5) 6) “.wma” LPCM6)“.wav” FLAC6)“.flac” PhotoJPEG“.jpg,” “.jpeg,” “.mpo” PNG“.png” GIF“.gif” ?To avoid data corruption or damage to the USB memory or devices, turn the receiver off when connecting or removing the USB memory or devices. ?Concerning the formats defined in the DLNA gu

20、idelines, the server is required to offer the content to which the format information defined in the DLNA guidelines has been added properly. General (US and Canadian models) Power requirements 120 V AC, 60 Hz Power consumption480 W Power consumption (during standby mode) 0.5 W (When “Control for HD

21、MI”, “Pass Through”, “Network Standby”, and “RS232C Control” are set to “OFF,” and the power for zone 2/zone 3 is turned off.) Dimensions430 mm 187.5 mm 420 mm (17 in 73/8in 161/2in) (width/height/depth) including projecting parts and controls Mass (Approx.)17.7 kg (39 lb 1 oz) Supplied accessories

22、Operating Instructions (1) Quick Setup Guide (1) Software License Information (1) Optimizer microphone ECM-AC1 (1) FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) AC power cord (mains lead) (1) Multifunction remote control (1) Simple remote control (1) R6 (size-AA) batteries (4) Speaker co

23、rd connection tool (1) Design and specifications are subject to change without notice. Standby power consumption 0.5 W. Amplifier section (AEP and UK models) POWER OUTPUT1) 2) Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0.09%): 120 W + 120 W Reference Power Output at Stereo Mode (4 o

24、hms 20 Hz 20 kHz, THD 0.15%): 120 W + 120 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT: 130 W + 130 W CENTER: 130 W SURROUND: 130 W + 130 W SURROUND BACK: 130 W + 130W Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT: 120 W + 120W CENTER: 120 W SURROUND: 120 W + 120W SURROUND BACK: 1

25、20 W + 120 W 1) Measured under the following conditions: Power requirements: 230 V AC, 50/60 Hz 2) Depending on the sound field settings and the source, there may be no sound output. AM tuner section (AEP and UK models) Tuning range531 1,602 kHz Intermediate frequency 450 kHz Antenna (aerial)Loop an

26、tenna (aerial) General (AEP and UK models) Power requirements 230 V AC, 50/60 Hz Power consumption 480 W Power consumption (during standby mode) 0.5 W (When “Control for HDMI”, “Pass Through”, “Network Standby”, and “RS232C Control” are set to “Off,” and the power for zone 2/zone 3 is turned off.) D

27、imensions430 mm 187.5 mm 420 mm (width/height/depth) including projecting parts and controls Mass (Approx.)17.3 kg RadioFans.CN 收音机爱 好者资料库 STR-DA5700ES 2 NOTES ON CHIP COMPONENT REPLACEMENT Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged

28、 by heat. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described b

29、elow. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester

30、, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated A

31、C voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) 1.5 k0.15 F

32、AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THE

33、SE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONC- T

34、IONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DON- NS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. *Manufactured under license from Dolby Laboratories

35、. Dolby, Pro Logic, Surround EX, and the double- D symbol are trademarks of Dolby Laboratories. * Manufactured under license under U.S. Patent Nos: 5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195, 7,333,929, 7,548,853 2.0_7_M J-2501-346-A

36、2.07 For CONTROL Board (CN2771) 2.0_7_FFor A AUDIO Board (CN727) FFC cable 8PJ-2501-360-ALength 300 mm A AUDIO BOARD SERVICE POSITION Please connect following extension jig. MAIN BOARD SERVICE POSITION Connect extension jig 0 to the A AUDIO board (CN727) and CONTROL board (CN2771). A AUDIO board (CN

37、727) CONTROL board (CN2741) insulating sheet A AUDIO board (CN601) CONTROL board (CN2771) Connect extension jig 6 to the A AUDIO board (CN601) and CONTROL board (CN2741). alligator clip Note: Connect altogether the metal part on the boards connected with the chassis using the alligator clip. MAIN bo

38、ard insulating sheet rear panel block CONTROL board alligator clip Note: Connect altogether the metal part on the boards connected with the chassis using the alligator clip. STR-DA5700ES 12 SECTION 2 DISASSEMBLY This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. CASE B

39、LOCK (Page 13) SET 2-4. D-AUDIO BOARD BLOCK-1 (Page 14) 2-7. D-VIDEO BOARD BLOCK-1 (Page 16) 2-8. D-VIDEO BOARD BLOCK-2 (Page 17) 2-10. NETWORK BOARD BLOCK-1 (Page 18) 2-16. A AUDIO BOARD-1 (Page 22) 2-17. A AUDIO BOARD-2 (Page 23) 2-11. NETWORK BOARD BLOCK-2 (Page 19) 2-5. D-AUDIO BOARD BLOCK-2 (Pa

40、ge 15) 2-6. HAT BOARD (Page 15) 2-9. D-VIDEO BOARD (Page 17) 2-15. TUNER (FM/AM) (TU1) (Page 21) 2-18. BRACKET (LARGE) BLOCK, FUSE (F1403, F1404) (Page 23) 2-19. DCDC2 BOARD (Page 24) 2-23. E-VOL BOARD (Page 26) 2-25. MAIN BOARD BLOCK (Page 27) 2-26. MAIN BOARD (Page 28) 2-13. A-VIDEO BOARD (Page 20

41、) 2-14. CONTROL BOARD (Page 21) 2-12. DC FAN (40 mm) (M1), NETWORK BOARD (Page 19) 2-3. D-AU_CONNECT BOARD (Page 13) 2-20. FUSE (F1401, F1402), ACDC/DCDC BOARD BLOCK (Page 25) 2-21. POWER TRANSFORMER (T001) (Page 25) 2-22. SPTM BOARD, FUSE (F03, F004, F901) (Page 26) 2-24. HEAT SINK BLOCK (Page 27)

42、2-27. FRONT PANEL BLOCK (Page 29) STR-DA5700ES 13 2-3. D-AU_CONNECT BOARD Left front side view Note: Follow the disassembly procedure in the numerical order given. 2-2. CASE BLOCK 7 case block 1 two screws (BVST4 ? 8) 1 two screws (BVST4 ? 8) 2 screw (BVT DIA.3) 3 two screws (BVTP3 ? 8) 4 4 5 6 1 fa

43、n connector (CN2407) 2 connector (CN1107) 3 connector (CN2403) 5 connector (CN2405) 6 connector (CN2406) 7 D-AU_CONNECT board 4 connector (CN2404) STR-DA5700ES 14 2-4. D-AUDIO BOARD BLOCK-1 Left front side view 1 Wire is removed from two lead pins. 5 Wire is removed from the lead pin. 5 Wire is remo

44、ved from the lead pin. 2 connection cord (HDMI cable) (CN3524) 3 connector (CN3571) 4 connector (CN2211) (AEP, UK) 6 screw (P3 ? 6) 7 seven screws (BVTP3 ? 8) 7 two screws (BVTP3 ? 8) ? ? ? lead pin D-AUDIO board D-VIDEO board HAT board rear side ? ? ? lead pin lead pin D-AUDIO boardA-CLASS_AMP boar

45、d front side heat sink Note: Process so that lead wire does not contact heat sink. SAFETY STANDARD STR-DA5700ES 15 2-6. HAT BOARD Left front side view lead pin lead pin lead pin ? rear side 1 Lift up the D-AUDIO board block in the direction of an arrow. D-AUDIO board 8 D-AUDIO board block 2 Wire is

46、removed from two lead pins. 3 connector (CN2207) 5 connector (CN2200) 6 connector (CN2204) 7 connector (CN2213) 4 connector (CN2401) ? 1 connector (CN2941) 4 Lift up the HAT board in the direction of an arrow. 6 HAT board 2 screw (BVTP3 ? 8) 3 two screws (supplied with J861) J861 5 wire (flat type)

47、(19 core) (CN807) 2-5. D-AUDIO BOARD BLOCK-2 Note: When replacing the D-AUDIO board in this unit for AEP and UK models, refer to “NOTE OF REPLACING THE IC2239 ON THE D-AUDIO BOARD AND THE COMPLETE D-AUDIO BOARD” (page 6). Left front side view STR-DA5700ES 16 2-7. D-VIDEO BOARD BLOCK-1 qd Lean the CO

48、NTROL board in the direction of an arrow. 2 connector (CN3510) 5 connector (CN3523) 9 connector (CN3611) 0 connector (CN3509) 7 connector (CN3607) 8 connector (CN3608) 1 Wire is removed from the lead pin. (See Fig. B) 4 Wire is removed from the clamp (L35). (See Fig. A) 4 Wire is removed from the cl

49、amp (L35). (See Fig. A) 3 wire (flat type) (21 core) (CN2861) A A 6 connection cord (HDMI cable) (CN3526) qa two screws (BVTP3 ? 8) qa screw (BVTP3 ? 8) qa screw (BVTP3 ? 8) qs bracket (CTRL) (AEP, UK) (AEP, UK) ? ? ? lead pin CONTROL board clamp (L35)clamp (L35) D-VIDEO board D-VIDEO board rear side rear side ? ? A ? ? ? ? STR-DA5700ES 17 2-9. D-VIDEO BOARD 2-8. D-VIDEO BOARD BLOCK-2 1 seven screws (B3 ? 5) 2 three scre