Yamaha-CDRD-651-Service-Manual电路原理图.pdf

《Yamaha-CDRD-651-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDRD-651-Service-Manual电路原理图.pdf（36页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDR-D651 SERVICE MANUAL COMPACT DISC RECORDER CDR-D651 100732 I CONTENTS TO SERVICE PERSONNEL . 1 REAR PANELS . 3 SPECIFICATIONS. 4 INTERNAL VIEW . 4 DISASSEMBLY PROCEDURES . 56 TEST MODE . 78 ERROR MESSAGE. 910 -COM DATA . 1115 BLOCK DIAGRAM. 1617 PRINTED CIRCUIT BOARD . 1823 SCHEMATIC DIAGRAM . 24

2、25 PARTS LIST. 2637 DISPLAY DATA . 38 REMOTE CONTROL TRANSMITTER . 39 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Produc

3、ts, are already known and understood by the users, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specif

4、ied. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certifica

5、tion or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striv

6、ing to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive compon

7、ents. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CDR-D65

8、1 P.O.Box 1, Hamamatsu, Japan RadioFans.CN 收音机爱 好者资料库 CDR-D651 1 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plast

9、ic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR AN

10、Y REA- SON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling foo

11、d. I TO SERVICE PERSONNEL 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is

12、imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. GMeter impedance should be equivalent to 1500 ohm shunted by 0.15F. GLeakage current must not exceed 0.5mA. GBe sure to test for leakage with the AC plug in both polarities. WARNING: Laser Safety T

13、his product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) When testing and/or repairing any comp

14、onent within the product, keep your eyes and skin more than 30 cm away from the laser pick-up unit at all times. Do not state the laser beam at any time. 2) Do not attempt readjustment, disassemble or repair of the laser pick-up, unless noted elsewhere in this manual. 3) CAUTION: Use of controls, ad

15、justments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Emitting conditions: 1) When the Top Cover is removed, and POWER SW is turned to the ON position, the laser component will emit a beam for several seconds to detect if a disc is

16、 present. During this time (5 - 10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period! If no disc is detected, the laser will stop emitting the beam. When a disc is set, you will not be exposed to any laser emissions. 2) The laser

17、power level can be adjust with VR on pick-up PWB, however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from

18、the device. RadioFans.CN 收音机爱 好者资料库 CDR-D651 ANALOGDIGITAL LINE ININLINE OUTOUT 43 L R L R RECPLAY OPTICAL B, G, R models A, B, G, R models 2 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs a laser. Therefore, be sure to carefully follow the instructions below when servicing . 1

19、. Laser Diode Properties CD (Drive A) G Material: GaAlAs G Wavelength: 790 nm G Emission Duration : Continuous G Laser Output: max. 180 W* G ANSI Class: Class 1 CDR (Drive B) G Material: GaAlAs G Wavelength: 790 nm G Emission Duration : Pulse G Laser Output: Write mode: max. 10 mW* (Duty 50%) G ANSI

20、 Class: Class 2 *This output is the value measured at a distance of about 200 mm from the objective lens surface on the Optical Pick-up Block. 2. When checking the laser diode emission, keep your eyes more than 30 cm away from the objective lens. VARO!:AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET AL

21、TTIINA NKYMTTMLLE LASER-STEILYLLE. L KATSO STEESEEN. VARNING!:OSYNLIG LASERSTRLNING NR DENNA DEL R PPNAD OCH SPRREN R URKOPPLAD. BETRAKTA EJ STRLEN. CDR-D651 ANALOGDIGITAL VOLTAGE SELECTOR LINE ININLINE OUTOUT 43 L R L R RECPLAY OPTICAL MODEL NO. CDR-D651 110/120/220/240VOLTS 50/60Hz MADE IN MALAYSI

22、A 24WATTS V621710 (R)-1 S E M K O V E R I F I E D ANALOGDIGITAL LINE ININLINE OUTOUT 43 L R L R RECPLAY OPTICAL MODEL NO. CDR-D651 230VOLTS 50Hz MADE IN MALAYSIA 24WATTS V610410 (B,G)-1 EMC ANALOGDIGITAL LINE ININLINE OUTOUT 43 L R L R RECPLAY OPTICAL MODEL NO. CDR-D651 240VOLTS 50Hz MADE IN MALAYSI

23、A 24WATTS N89 V610400 (A)-1 ANALOGDIGITAL LINE ININLINE OUTOUT 43 L R L R RECPLAY OPTICAL MODEL NO. CDR-D651 120VOLTS 60Hz MADE IN MALAYSIA 24WATTS V610390 (U,C)-1 3 I REAR PANELS B, G model U, C models A model R model CDR-D651 435 (17-1/8) Unit : mm (inch) 117 (4-1/4) 17 (11/16)100 (3-15/16) 285 (1

24、1-1/16) 4 I SPECIFICATIONS I Audio Performance Frequency Response Playback (5Hz to 20000Hz)0 0.5dB Signal to Noise Ratio (IHF-A-Network) Playback100dB Recording90dB Total Harmonic Distortion (1kHz) Playback0.004% Recording0.02% Dynamic Range Playback95dB Recording85dB I Laser Diode Properties CD (Dr

25、ive A) MaterialGaAlAs Wavelength780 25nm Emission durationContinuous Laser outputMax: 180W CDR (Drive B) MaterialGaAlAs Wavelength780 5nm Emission durationPulse Laser outputWrite mode: Max 10mW (Duty 50%) I Inputs LINE IN (REC) TypePin jack Standard input level700mV / 20k DIGITAL IN OPTICAL TypeSqua

26、re optical connector jack I Outputs LINE OUT (PLAY) TypePin jack Standard output level (1kHz, 0dB)2.0 0.5Vrms DIGITAL OUT OPTICAL TypeSquare optical connector jack PHONES Standard output level (150 short / input -20dB)300mV DIMENSIONS 1234 5678 I INTERNAL VIEW 1 OPE P.C.B. (7) 2 OPE P.C.B. (3) 3 OPE

27、 P.C.B. (2) 4 OPE P.C.B. (4) 5 CD Drive Mechanism Unit 6 OPE P.C.B. (1) 7 OPE P.C.B. (5) 8 MAIN P.C.B. (Top side), CD-R Drive Mechanism Unit (Bottom side) I General Power Supply U, C modelsAC120V, 60Hz B, G modelsAC230V, 50Hz A modelAC240V, 50Hz R modelsAC110/120/220/240V, 50/60Hz Power Consumption

28、24W Dimensions (W x H x D)435 x 117 x 285mm (17-1/8 x 4-1/4 x 11-1/16) Weight 5 kg (13lbs. 14oz.) Finish Black, Titan (G model) Accessories RCA Pin Cables x 2 Optical Fiber Cable x 1 Remote Control Transmitter Batteries x 2 * Specifications subject to change without notice. U . U.S.A. modelC . Canad

29、a model G. Europe modelB . British model A . Australia modelR . General model CDR-D651 8 9 1 1 2 3 4 4 6 5 7 7 Frame/CDR CB105 A CB307 CB301 CB202 A A A 5 I DISASSEMBLY PROCEDURES (Remove parts in the order as numbered.) Disconnect the power cord from the AC outlet. 1. Removal of Top Cover a. Remove

30、 4 screws (1) and 3 screws (2) in Fig. 1. b. Remove the Top Cover. 2. Removal of Front Panel a. Remove 2 screws (3) and 4 screws (4) in Fig. 1, and then remove the Frame/CDR. b. Disconnect 3 connectors (CB105, CB301, CB307 in Fig. 2) from the MAIN PCB and a connector (CB202 in Fig. 2) from the OPE P

31、CB (6). c. Remove a screw (5) in Fig. 1 fixing the OPE PCB (5). d. Remove 4 screws (6) and 2 screws (7) in Fig. 1. e. Release 2 hooks at the right and left of the Front Panel in Fig. 1, and then remove the Front Panel forward. 3. Removal of Tray (applicable to both CD drive and CD-R drive models) a.

32、 Remove the Front Panel. b. Check that the pick-up is in the inner track position. If it is not, move it to the inner track position. (At this time, never touch the lens.) c. Lower the pick-up mechanism by turning the gear on the front face of the drive to the right. (Fig. 3) d. Pull out the Tray fo

33、rward. e. While pushing the lever (8) toward the left, lift up the lever (9). Then with the lever held up, remove the Tray by pulling it forward. (Fig. 4) *If the pick-up is not at a position along the inner track on the CD-R drive side, perform the following procedure. a. Disconnect all connectors

34、of the Main PCB. b. Remove 4 screws (A) fixing the Main PCB. (Fig. 2) c. Remove the Main PCB. d. Move the pick-up to a position along the inner track by pushing it lightly with finger. (At this time, never touch the lens.) Fig. 1 Fig. 2 Fig. 3 Fig. 4 CDR-D651 A B A B A B D E Connector Connector B B

35、B C C C 0 A 6 4. Removal of Pick-up Mechanism on CD drive side a. While pushing the claw (0) to the left, release the pin on the left side of the Pick-up Mechanism Unit from the CD mechanism chassis. (Fig. 5) b. Release the pin on the right side by sliding the Pick-up Mechanism Unit toward the left,

36、 and then slide the Pick- up Mechanism Unit by moving it rearward. c. Disconnect the flexible flat cable (A) connected to the pick-up mechanism unit. d. Remove the pick-up mechanism unit from the CD mechanism chassis. 5. Removal of CD Drive Mechanism Unit a. Remove 4 screws (B). (Fig. 6) b. Disconne

37、ct 2 connectors. (Fig. 7) c. Disconnect the flexible flat cable (A) connected to the pick-up mechanism unit. (Fig. 5) d. Remove the CD drive mechanism unit from the main chassis. 6. Replacement of CD-R Mechanism Unit Belt a. Remove the Tray of the CD-R Mechanism Unit. (See Step 3.) b. Remove the bel

38、t (D) visible from the front with tweezers or the like. (Fig. 8) c. Using alcohol, clean the belt contacting section of the pulley. d. Using tweezers or the like, install a new belt to the pulley A first and then B as shown in Fig. 8. At this time, use care so as not to allow the belt to be twisted

39、or grease to attach to it. 7. Removal of CD-R Drive Mechanism Unit a. Remove the MAIN PCB. b. Remove 4 screws (C). (Fig. 6) c. Remove the CD-R drive mechanism unit from the main chassis. 8. Installation of Tray (applicable to both CD drive and CD-R drive models) a. Slide the slide gear (E) to the ri

40、ght to attain the state with the pick-up mechanism lowered. (Fig. 8) b. Load the tray from the front. c. Reversing the procedure for unloading the tray, make the gear at the front of the drive turn to the left so that the pick-up mechanism is raised fully. Fig. 5 Fig. 6 Fig. 7 Fig. 8 CDR-D651 Front

41、panelRemote controllerCODEPCB Test Mode (service) (A) OPEN/CLOSE(A) OPEN/CLOSE81 (A) Drive open/close (A) PLAY/PAUSEPLAY82 (A) Playback if FOCUS ON (A) STOPSTOP84 (A) All at stop (A) SKIP -SKIP -86 (A) FEED shift toward inner track (A) SKIP +SKIP +87 (A) FEED shift toward outer track (B) OPEN/CLOSE(

42、B) OPEN/CLOSEC1 (B) PLAY/PAUSE (A) Spindle acceleration (B) STOP (A) All at stop (B) SKIP MUTE OFF (B) SKIP MUTE ON DISPLAY A DISPLAY B TEXT/TIME FL display test RECRECA0 REC MUTEREC MUTEA1 COPYCOPYA3 REC MODEREC MODEA2 Servo gain changed *1 TRACK No.TRACK No. WRITEA7 Version check *2 FINALIZEFINALI

43、ZEA5 EEPROM test ERASEERASEA6 Output changed INPUTINPUTAB Analog input changed DISPLAY A/B9F TEXT9D 7 I TEST MODE Test Mode In the test mode, only the CD drive side functions. There are two test modes. One is Product Test Mode and the other is PCB Test Mode. In both modes, the test results can be ch

44、ecked with the contents displayed on the fluorescent character display tube. Refer to the separate table for the contents to be displayed. Starting the Test Mode 1. In the power off state, press the POWER button while pressing ( ) and ( ) buttons of the DISC A side of the Front Panel. 2. When the po

45、wer is turned on and the hand is off from the button, the mode is set to the Product Test Mode. At this time, “FQA Mode” appears on the display. Changing to the PCB Test Mode (service) Operation on the main unit: 1. In the Product Test Mode, push the MULTI JOG knob. 2. Select the test mode by turnin

46、g the MULTI JOG knob. At this time, “PCB Test” appears on the display. 3. Press the MULTI JOB knob to finalize the mode selection. Operation on the remote controller: 1. Press the EDIT button. 2. Press the DELETE button and select the test mode. At this time, “PCB Test” appears on the display. 3. Pr

47、ess the SET button to finalize the mode selection. After either of the above operations, the mode changes to the PCB Test Mode. Use the same procedure to change the mode from the PCB Test Mode to the Product Test Mode. CDR-D651 Front panelRemote controllerCODEPCB Test Mode (service) TIME9E FL display test DIMMER9C Dimmer test MENUBA Not used for service -BC Not used for service +BB Not used for service EDITB0 Not used for service DELETEB1 Not used for service SETB2 Not used for s